Shantou City Ourui Industrial 3715-1A 2.4GHz Dinosaurs Remote Control Instruction Manual
- June 4, 2024
- Shantou City Ourui Industrial
Table of Contents
Shantou City Ourui Industrial 3715-1A 2.4GHz Dinosaurs Remote Control
A set of 3. 7V rechargeable lithium batteries supplies power for the main body of the toy.
The uses 2 1.SV
AA non-rechargeable batteries.
Precautions on using the batteries
- The remote control requires two 1.5V AA non-rechargeable ~~ batteries (not provided)
- The toy body requires one set of 3.N rechargeable batteries (provided);
- Do not charge the non-rechargeable batteries;
- Do not mix new and old or different types of batteries;
- Please note the polarity when installing or replacing the battery;
- Please timely take out the battery with low power;
- Do not short circuit the power supply terminal;
- Remove and load the non-chargeable batteries; Use the screwdriver to release the screws on the battery cover. Uncover the battery cover and load or remove the batteries as per the correct “+/-“polarity and then close the battery cover. Wrench tightly the screws on the battery cover by screwdriver.
- This rechargeable battery is non-replaceable, and the rechargeable battery can only be charged under the supervision of adult;
- Connect the supplied USB charger to the power supply with output voltage of 5.0V 500mA; (such as: USB mobile phone charger, computer USB interface) to charge the battery;
- During charging. the USB charger will be slightly , warm which is normal;
- . The product can only be charged with the recommended USB charger, and the USB charger is not a toy;
- Regularly check whether the wire, plug. casing and other parts of the USB charger and the recommended charger are damaged. ~there’s any damage, stop using it before it is repaired;
- Disconnect the USB charger before cleaning the toy;
- Please do not disassemble or throw the bad batteries and battery pack into fire or water to avoid accident;
- The toy must not be used by children underage 3.
Frequency pairing
Please make the remote control and the dinosaur mam body close frequency pa1rmg to each other as much as possible during the frequency paining.
Tum on the power of the remote control and L main body. When the frequency pairing is successful, the lights of the remote control and the dinosaur main body are constantly on and the main body will emit sound effects. (If the Sound light keeps flashing. the frequency pairing is hole unsuccessful, please tum off the power of the remote control (press and hold the power button for 3 seconds) and the power of the dinosaur main body (press and hold the main body demo button for 3 seconds), and then turn on the power again to conduct the frequency pairing’
Note: The dinosaur body and remote control will enter the dormant state after idle running for five minutes. Press and hold the Demo button on the main body for 3 seconds to reawaken it (at this time the demo mode of dinosaur body will be initiated), and turn on the power using the remote control.
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>