SHANTOU K6MAX Mini Drone 4K Professional Three Cameras

Product Information

Specifications :

• Model: [Product Model]
• Compliance: FCC Part 15
• RF Exposure: General exposure requirement met
• Usage: Portable

Product Usage Instructions

FCC Compliance:

This device complies with part 15 of the FCC Rules. It must not cause harmful interference and must accept any received interference.

Operation Conditions:

Ensure the device is operated under normal conditions to prevent undesired operation.

Modifications:

Do not make changes or modifications not approved by the responsible party as it could void the user’s authority to operate the equipment.

RF Exposure:

The device meets general RF exposure requirements and can be used in portable conditions without restrictions.

FAQ

• Q: Can I modify the device for better performance?
  • A : No, any modifications not approved by the responsible party can void your authority to operate the equipment.
• Q: Is there a limit to portable usage?
  • A : The device can be used in portable exposure conditions without restrictions as it meets the necessary requirements.

Folded wing

• No obstacle avoidance function in high gear

• Please install the protector first to protect the motor and prevent injury to others

Replace rotor blade

• Please make sure that it is installed correctly, otherwise it will not be able to fly normally

Transmitter

• No steering gear version, invalidity on the lens/lens

Install battery for aircraft and transmitter

1. Please do not mix old and new batteries together
2. Please do not mix different types of batteries together
3. Please replace the battery when the low voltage prompts
4. Please remove the battery if not playing for a long time

Battery charging

1. Remove the battery from the aircraft
2. Insert the battery into the USB charging cable
3. Insert the USB charging cable into the power of the computer USB interface,

The red light indicates thar the battery is charging.

• Tips: please remove the battery from the USB charging cable when the battery is charged completely
• light on : Charging
• light out : Completely

Altitude hold function

After using the left joystick(Accelerator) to control the ascending/descending flight of the aircraft, free up the left joystick (Accelerator) and the aircraft will still hover at that height when the joystick is free.

Tips: the first push the left joystick up to start the motor,it doesn’t make the aircraft fly the second push the left joystick up to let the aircraft rise

Ready to fly your aircraft

1. Make sure the battery on the aircraft is fully charged;
2. After the battery is installed in the aircraft, press the power button on the top. The blue light flashes to indicate that the connection is normal. Place the aircraft on a level ground. The aircraft prompt light flashes to indicate that the aircraft enters the code matching state;
3. After the battery is loaded into the remote control, press the power button, and the blue light flashes to indicate that it enters the code-matching state;
4. The remote control and the UAV will automatically pair codes with each other as soon as the switch is turned on. If the light on the aircraft is always on, the code pairing is completed.
5. Now you can push the power remote control to freely control the aircraft to fly.

Operating direction

Fine-tuning operation

When the aircraft is hovering in the air, in the event that the aircraft is automatically advancing forward or backward, flying sideward on the left or right, it can be rectified by doing the following.

Horizontal calibration

You Can use the horizontal calibration function to call: H’ate the aircraft. when It drifts in a oertain direction in the air or when It rotates on the spot. Place Iha aircraft on a horizontal surface, move the direction control lever on the remote control. end the remote control emits a beep. At the same time, the blue light of 1ha airt raft flashes. Wait for about 3 seconds, the hlue light of the aircraft. is always on, and the calibration is i::omple1ed.

3D eversion

When you are familiar with the basic operation, you can do some awesome& exciting tricks and stunts! First of all, fly the aircraft to a height of more than 3 meters, press the 3DEveretion switch
on the rear r1ghr side of the transmitter, then push the right rudder(in any direction) to make a 360-degree flip.

Tips: 3D eversion goes better battery power is enough

Headless function

No matter which direction the aircraft may rotate to, the flying direction direction will be as per the direction that the decoding is made.

Tips: Before entering into the headless mode, please confirm the forward direction of the decoding

Low-voltage protection

All lights flashing indicate that the battery is low when the aircraft is flying in the sky.

Slow flashing : Battery low power

Tips: Aircraft can not be rolled in the case of low-power

One key to rise/down

One key to rise:

When the aircraft is on the ground, Press the button “One key to ries” on the transmitter,At this time the aircraft will automatically rise toa height of 1.5  meters. One key to down:

When the aircraft stays in the air, press the descending button in the lower left corner of the remote control, and the aircraft will automatically descend to the ground at this time.

Forced stop

For fixed versions,the aircraft does not stop immediately when the power remote rod is pulled down to the lowest level.As shown in the figure on the right, press the emergency stop button for 2 seconds, and the aircraft will force it to stop.

Tip : this opportunity Is very useful In emergency situations

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

portable device statements

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>