Xhorse XSGA Universal Remote Key User Manual
- July 10, 2024
- Xhorse
Table of Contents
Xhorse XSGA Universal Remote Key
Product Specifications
- Model: XSGA Universal Remote Key
- Battery Type: 2032, 3V
- Frequency Band: RFID (433.92 MHz)
- Max Permitted Power: -44.25 dBm
Product Usage Instructions
Changing the Battery:
- Press the backside button to release the mechanical key holder.
- Insert a tool into the gap to separate the shell.
- Remove the old battery and replace it with a new 2032 3V battery. Ensure correct polarity.
- Reassemble the key as before.
Pairing Method:
To pair the remote key with a vehicle, refer to the specific instructions provided by the vehicle manufacturer for your model.
FAQ:
-
Q: What type of battery does the XSGA Universal Remote Key use?
A: The remote key uses a 2032 battery with 3V. -
Q: How do I know if the battery needs to be changed?
A: You may need to change the battery when the remote key stops responding to button presses or when the range decreases significantly. -
Q: Can I use the remote key in different models of vehicles?
A: The compatibility of the remote key with different vehicle models may vary. It is recommended to refer to the specific pairing instructions for each vehicle model.
Overview
XSGA Universal Remote Key is suitable for vehicle which contains the Xhorse
receiver.
Note : The operating temperature of the product is -20–50℃.
Button description
| 1 | Lock button |
|---|---|
| 2 | Unlock button |
| 3 | Trunk button |
| 4 | Panic button |
Change battery
First use or when the battery runs out need to change a new battery, following steps
-
Press the back side button for lose the mechanical key holder
-
Use the tool into the gap to separate the shell
-
Take the battery out and replace new one
Note : The battery type is 2032 with 3V, ensure the positive and negative of the battery is correct -
Install the key the same as before
Pairing method
Pairing with vehicle : Referring to the corresponding vehicle models to match.
FCC statements
15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
§ 15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment
§ 15.105 Information to the user.
Note : This equipment has been tested and found to comply with the limits
for a Class B digital device, under part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used by the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning for Portable device:
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction
CE & UKCA statements:
Frequency Band(s)
This device operates with the following frequency bands and maximum frequency
power.
Note : The product is compliant with these power limits required by the
European Union. Frequency bands supported by the product vary by model.
RFID (433.92 MHz) Max Pe.r.p. is -44.25 dBm.
EU & UKCA DECLARATION OF CONFORMITY
Hereby, Shenzhen Xhorse Electronics Co., Ltd. declare that Universal Remote Key with model XSGA is in compliance with Directive 2014/53/EU, 2011/65/EU and RER 2017 (SI2017/1206).
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>