THERMORY Barrel N53 6 Person Barrel Sauna Installation Guide
- July 9, 2024
- THERMORY
Table of Contents
THERMORY Barrel N53 6 Person Barrel Sauna
Product Specifications
- Designed for up to two people
- Includes various parts for assembly
- Dimensions: 7′ x 7′ x 7′
Product Usage Instructions
Step Zero: Preparing the Site
Before you begin, ensure the sauna will fit in your chosen location. The ideal space should have dimensions of 7′ x 7′ x 7′. Make sure the site is level and free of standing water after rainfall. It is recommended to place the sauna on concrete, pavers, or crushed stone.
Step One: Setting Up Support Cradles
Measure support cradles (A) diagonally from corner to corner to ensure they are square. Place the support cradles on a level site. Be sure the cradles remain level for better stability.
Step Two: Placing Center Stave
Place the center stave (B) on wooden dowels embedded in outer support cradles (A). Secure the center stave with screw 4.2×70 (N).
Step Three: Attaching Body Staves
Place 6 sauna body staves (C) on each side of the center stave (B) and fix them with screws 4.2 x 70 (N). Ensure to align the panel groove on every next body stave.
Step Four: Installing Front and Rear Panels
Place the front panel with sauna doors (F2) and rear panel (E2) into the trimmed grooves. Make sure each panel is centered, leveled, and completely seated into the floor panel. Bind these panels together temporarily by placing one or two body staves on top of them.
Step Five: Attaching Side Panels
Attach two front side panels (F, F1) to the front panel (F2) and two back side panels (E, E1) to the rear panel (E2) using screws 5.0 x 120 (M) and stainless steel screws 4.20 x 70 (N1). Ensure the bench supports face the interior of the sauna.
Frequently Asked Questions
Q: How many people can fit in the Thermory Barrel Sauna?
A: The Thermory Barrel Sauna is designed for up to two people.
Q: What tools are required for assembly?
A: The recommended tools for assembly include two of each of the following: screw 5.0×120, screw 4.2×70, and hex nut M16 (SW24).
Q: What is the ideal location for setting up the sauna?
A: It is recommended to place the sauna on a level surface free of standing water, such as concrete, pavers, or crushed stone.
Everything you need to build your very own Thermory Barrel Sauna is right
there in front of you. If it looks like a lot, it is. If it seems too
complicated to assemble, it isn’t.
These instructions are specifically wri°en to guide you through each step with
ease. And if you need additional encouragement, you can scan the code on the
back of this guide to see how it’s done.
The Thermory Barrel Sauna No53 is designed for up to two people. That’s plenty
of room for you and the friends helping you put this together. But if you want
to enjoy the first steam all by yourself, we understand.
The Wait Is Over.
We truly appreciate the opportunity to share our love of sauna culture with
you. And if there’s anything we can do to make your sauna experience better,
please don’t hesitate to let us know. If not, just relax and enjoy.
PARTS 1
PARTS 2
Installation guide
-
STEP ONE
Measure support cradles (A) diagonally from corner to corner.
Measurements “a” and “b” should be equal to ensure the cradles are square.
Be sure cradles remain level. -
STEP TWO
Place the support cradles (A) on level site. The middle support cradle will have no dowel. Carefully level for be°er stability.
Place the center stave (B)
on wooden dowels embedded in outer support cradles (A).
Fix the center stave (B) with screw 4.2×70 (N). -
STEP THREE
Place 6 sauna body staves (C) to each side of the center stave (B) and fix with screws 4.2 x 70 (N).
Be sure to align the panel groove on every next body stave.
-
STEP FOUR
Place front panel with sauna doors (F2) and rear panel (E2) into the trimmed grooves. Be sure each panel is centered, leveled, and completely seated into the floor panel.
Bind these panels together by temporarily placing one or two body stave (C) on top of them. -
STEP FIVE
Two front side panels (F, F1) a°ach to the front panel (F2) and two back side panels (E, E1) a°ach to the rear panel (E2) by 4 screws 5.0 x 120 (M) and 4 stainless steel screws 4.20 x 70 (N1).
Be sure the bench supports face the interior of the sauna.
Confirm that the combined width of the rear wall (E, E2, E1) matches the combined width of the front wall (F, F2, F1).
-
STEP SIX
Continue placing body staves (C) tightly on both sides of the sauna using rubber mallet, while fixing body staves on the front panel with 4.2 x 70 screws.
To finish the roof top joint, use top stave (H). -
STEP SEVEN
- Install steel bands (I) by wrapping bands around barrel prior to connecting with bolts and nuts (U).
- Place steel bands evenly around barrel, covering screw heads.
- Measure from steel band to barrel edge to ensure the steel band is even.
- Cover roof with roof tape.
- Rub and smooth with pressure to ensure adhesion.
- Install interior aspen roof trim (O) with 4.0 x 50 (P1) stainless steel screws.
-
STEP EIGHT
A°ach bench supporting leg (J1) to the bench (J), install two sauna benches on wall mounts using stainless steel screws 4.2 x 70 (N1).
Hold the seat and leg assembly tight to the sauna wall. Using a level, make sure the bench seat is level from front to back. This will ensure proper placement.
Install backrests (J2) at your chosen height using stainless steel screw 4.0 x 50 (P1). -
STEP NINE
Flooring duckboards (L) can be used for wiring runs, confirm specific wiring runs needed for chosen stove.
-
STEP TEN
Place waterproof roof cover (Z) and fix it with wooden slat (Z1) and screws 4.0 x 50 (P).
Install front and rear decorative roof finishing boards (W), fixing by screws 4.0 x 50 (P).
WATCH THE VIDEO
SEE HOW ASSEMBLY WILL LOOK HERE
Thermory USA – Denver
537 W. Highlands Ranch Pkwy, Ste. 114 Highlands Ranch, CO 80129 720.759.7268
support@thermoryusa.com
Thermory USA – Bu˜alo
56 Harvester Ave, Ste. 1-201
Batavia, NY 14020
585.591.6590
support@thermoryusa.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>