THERMORY No. 50 Barrel Sauna Installation Guide

: June 6, 2024
: THERMORY

Table of Contents

THERMORY No. 50 Barrel Sauna
Product Specifications
Product Usage Instructions
Frequently Asked Questions
Product Information
PARTS
Installation Instruction
Contact
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

THERMORY No. 50 Barrel Sauna

Product Specifications

Designed for up to four people
Outfitted with a window
Dimensions: 8′ x 7′ x 7′

Product Usage Instructions

Step Zero: Pre-installation Preparation

Before you begin, ensure the sauna will fit in your chosen location. Ideal dimensions are 8′ x 7′ x 7′. Ensure the site is level and free of standing water after rainfall. Preferred foundation materials include concrete, pavers, or crushed stone.

Step One: Cradle Setup

Measure support cradles (A) diagonally to ensure they are square. Keep them level.

Step Two: Placing Center Stave

Place the center stave (B) on the wooden dowels embedded in the outer support cradles (A). Secure with screws 4.2×70 (N).

Step Three: Attaching Body Staves

Place 6 sauna body staves (C) on each side of the center stave (B) and secure with screws 4.2 x 70 (N). Ensure alignment of the panel groove on each body stave.

Step Four: Installing Panels

Place door panel (F2) in the front slot and attach side panels (F, F1) using appropriate screws. Install rear panel (V) with bench supports facing the interior, ensuring proper alignment and seating.

Step Five: Finalizing Assembly

Continue placing body staves (C) until the halfway point. Place rear panel with window (E1) on rear panel (E) and secure with screws 5.0 x 120 (M).

Frequently Asked Questions

Q: How many people can the sauna accommodate?

A: The sauna is designed for up to four people.

Q: What are the preferred foundation materials for installation?

A: Concrete, pavers, or crushed stone are preferred for the sauna foundation.

Product Information

Everything you need to build your very own Thermory Barrel Sauna is right there in front of you. If it looks like a lot, it is. If it seems too complicated to assemble, it isn’t. These instructions are specifically written to guide you through each step with ease. And if you need additional encouragement, you can scan the code on the back of this guide to see how it’s done. The Thermory Barrel Sauna No50 is designed for up to four people and is outfitted with a window. That’s plenty of room for you and the friends helping you put this together. But if you want to enjoy the first steam all by yourself, we understand.

The Wait Is Over.

We truly appreciate the opportunity to share our love of sauna culture with you. And if there’s anything we can do to make your sauna experience better, please don’t hesitate to let us know. If not, just relax and enjoy.

PARTS

Installation Instruction

STEP 0

Before you begin, be sure the sauna will fit in your chosen location. Approximately L x W x H of 8′ x 7′ x 7′ is ideal. Overall dimensions are shown here. Be sure the site is level and free of standing water after rainfall Concrete, pavers or crushed stone is preferred.

STEP 1

Measure support cradles (A) diagonally from corner to corner. Measurements “a” and “b” should be equal to ensure the cradles are square. Be sure cradles remain level.

STEP 2

Place the support cradles (A) on level site. The middle support cradle will have no dowel. Carefully level for better stability. Place the center stave (B) on wooden dowels embedded in outer support cradles (A). Fix the center stave (B) with screw 4.2×70 (N).

STEP 3

Place 6 sauna body staves (C) to each side of the center stave (B) and fix with screws 4.2 x 70 (N). Be sure to align the panel groove on every next body stave.

STEP 4

Place door panel (F2) in front slot. Be sure panel is centered, leveled, completely seated. Attach side panels (F, F1) using 4 5.0 × 120 (M) screws and 2 4.2 x 70 (N1) stainless steel screws. Place rear panel (V) with bench supports facing interior. Confirm width of rear panel (V) matches the combined width of left panel section (F), front panel (F2) and right panel section (F1). These panels must be completely seated into the floor panel.

STEP 5

Place body staves (C) until the halfway point. Place rear panel with window (E1) on rear panel (E), fix by 2 screws 5.0 x 120 (M).

STEP 6

Continue placing body staves (C) tightly on both sides of the sauna using rubber mallet, while fixing body staves on the front panel with 4.2 × 70 screws and rear window panel with 4.0 x 50 screws to prevent glass breakage. To finish the roof top joint, use top stave (H).

WARNING!

Use shorter screw 4.0 x 50 (P) for rear panel E1 otherwise the window will be damaged!

STEP 7

Install steel bands (l) by wrapping bands around barrel prior to connecting with bolts and nuts (U). Place steel bands evenly around barrel, covering screw heads. Measure from steel band to barrel edge to ensure the steel band is even. Cover roof with roof tape. Rub and smooth with pressure to ensure adhesion. Install interior aspen roof trim (O) with 4.0 x 50 (P1) stainless steel screws.

STEP 8

Attach interior supporting leg (J1) to the bench (J), install two sauna benches on wall mounts using stainless steel screws 4.2 x 70 (N1). Hold the seat and leg assembly tight to the sauna wall. Using a level, make sure the bench seat is level from front to back. This will ensure proper placement. Install backrests (J2) at your chosen height using stainless steel screw 4.0 × 50 (P1).

STEP 9

Flooring duckboards (L) can be used for wiring runs, confirm specific wiring runs needed for chosen stove.

STEP 10

Place waterproof roof cover (Z) and fix it with wooden slat (21) and screws 4.0 x 50 (P). Install front and rear decorative roof finishing boards (W), fixing by screws 4.0 x 50 (P).

WATCH THE VIDEO

SEE HOW ASSEMBLY WILL LOOK HERE.