THERMORY Barrel 54 2 Person Barrel Sauna Installation Guide

: June 1, 2024
: THERMORY

Table of Contents

THERMORY Barrel 54 2 Person Barrel Sauna
Product Information
Product Usage Instructions
FAQs
INTRODUCTION
FEATURE
PARTS
ASSEMBLY STEPS
SEE HOW ASSEMBLY
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

THERMORY Barrel 54 2 Person Barrel Sauna

THERMORY-Barrel-54-2-Person-Barrel-Sauna-PRODUCT

Product Information

Specifications:
- Dimensions: 6′ x 7′ x 7′
- Capacity: Up to 2 people
- Materials: Wood, Stainless Steel

The Thermory Barrel Sauna No54 is designed for up to two people and is outfitted with a window. It provides a cozy sauna experience for you and a friend.

Product Usage Instructions

Step Zero – Pre-installation Preparation
- Before starting the installation process, ensure that the sauna will fit in your chosen location. The site should be level and free of standing water. Preferred surfaces include concrete, pavers, or crushed stone.
Step One – Assembly Preparation
- Measure support cradles (A) diagonally to ensure they are square. Place the support cradles on a level site and carefully level them for stability. Fix the centre stave (B) to the cradles using screws 4.2 x 70 (N).
Step Two – Body Staves Installation
- Place 6 sauna body staves (C) on each side of the centre stave (B) and fix them with screws 4.2 x 70 (N). Ensure proper alignment of the panel groove on each body stave.
Step Three – Panel Installation
- Place the door panel (F2) in the front slot, ensuring it is centred and levelled. Attach side panels (F, F1) using the specified screws. Place the rear panel (V) with bench supports facing the interior.
Step Four – Final Assembly
- Continue placing body staves (C) until the halfway point and then place the rear panel with window (V1) on the rear panel (V) and fix it with screws 5.0 x 120 (M).

FAQs

Q: How many people can the Thermory Barrel Sauna accommodate?
- A: The sauna is designed for up to two people.
Q: What are the recommended surface options for installation?
- A: Concrete, pavers, or crushed stone surfaces are preferred for installation.

INTRODUCTION

Everything you need to build your very own Thermory Barrel Sauna is right there in front of you. If it looks like a lot, it is. If it seems too complicated to assemble, it isn’t.
These instructions are specifically written to guide you through each step with ease. If you need additional encouragement, you can scan the code on the back of this guide to see how it’s done.
The Thermory Barrel Sauna No54 is designed for up to two people and is outfitted with a window. That’s plenty of room for you and the friends helping you put this together. But if you want to enjoy the first steam all by yourself, we understand.

FEATURE

The Wait Is Over.

We truly appreciate the opportunity to share our love of sauna culture with you.
And if there’s anything we can do to make your sauna experience better, please don’t hesitate to let us know.
If not, just relax and enjoy. $THERMORY-Barrel-54-2-Person-Barrel-Sauna-FIG-1 $1$$ $THERMORY-Barrel-54-2-Person-Barrel-Sauna-FIG-1 $2$$

PARTS

PARTS 1

$THERMORY-Barrel-54-2-Person-Barrel-Sauna-FIG-1 $3$$ PARTS 2 $THERMORY-Barrel-54-2-Person-Barrel-Sauna-FIG-1 $4$$

ASSEMBLY STEPS

STEP ZERO

Before you begin, be sure the sauna will fit in your chosen location.
Approximately L x W x H of 6’ x 7’ x 7’ is ideal. Overall dimensions are shown here.
Be sure the site is level and free of standing water after rainfall.
Concrete, pavers or crushed stone is preferred.

STEP ONE

Measure support cradles (A) diagonally from corner to corner.
Measurements “a” and “b” should be equal to ensure the cradles are square.
Be sure cradles remain level.

STEP TWO

Place the support cradles (A) on the level site. Carefully level for better stability.
Place the centre stave (B) on wooden dowels embedded in outer support cradles (A).
Fix centre stave (B) to cradles with screws 4.2 x 70 (N).

STEP THREE

Place 6 sauna body staves (C) on each side of the center stave (B) and fix with screws 4.2 x 0 (N).
Be sure to align the panel groove on every next body stave

STEP FOUR

Place the door panel (F2) in the front slot.
Be sure the panel is centred, levelled, and completely seated. Attach side panels (F, F1) using 4 5.0 x 120 (M) screws and 2 4.2 x 70 (N1) stainless steel screws.
Place rear panel (V) with bench supports facing the interior.
Confirm width of the rear panel (V) matches the combined width of the left panel section (F), front panel (F2) and right panel section (F1). These panels must be completely seated into the floor panel.

STEP FIVE

Place body staves (C) until the halfway point.
Place the rear panel with window (V1) on the rear panel (V), fixed by 2 screws 5.0 x 120 (M).

STEP SIX

Continue placing body staves (C) tightly on both sides of the sauna using a rubber mallet, while fixing body staves on the front panel with 4.2 x 70 screws and rear window panel with 4.0 x 50 screws to prevent glass breakage.
To finish the rooftop joint, use the top stave (H).
WARNING! Use a shorter screw 4.0 x 50 (P) for rear panel V1 otherwise, the window will be damaged! $THERMORY-Barrel-54-2-Person-Barrel-Sauna-FIG-1 $11$$

STEP SEVEN

Install steel bands (I) by wrapping bands around the barrel before connecting with bolts and nuts (U).
Place steel bands evenly around the barrel, covering screw heads.
Measure from steel band to barrel edge to ensure the steel band is even.
Cover the roof with roof tape.
Rub and smooth with pressure to ensure adhesion.
Install interior aspen roof trim (O) with 4.0 x 50 (P1) stainless steel screws.

STEP EIGHT

Attach the interior supporting leg (J1) to the bench (J), and install two sauna benches on wall mounts using stainless steel screws 4.2 x 70 (N1).
Hold the seat and leg assembly tight to the sauna wall. Using a level, make sure the bench seat is level from front to back. This will ensure proper placement.
Install backrests (J2) at your chosen height using stainless steel screw 4.0 x 50 (P1). $THERMORY-Barrel-54-2-Person-Barrel-Sauna-FIG-1 $13$$

STEP NINE

Flooring duckboards (L) can be used for wiring runs, confirm specific wiring runs needed for the chosen stove.

STEP TEN

Place waterproof roof cover (Z) and fix it with a wooden slat (Z1) and screws 4.0 x 50 (P).
Install front and rear decorative roof finishing boards (W), fixing by screws 4.0 x 50 (P). $THERMORY-Barrel-54-2-Person-Barrel-Sauna-FIG-1 $15$$
WATCH THE VIDEO