THERMORY 51 6 Person Barrel Sauna Installation Guide

: June 1, 2024
: THERMORY

Table of Contents

51 6 Person Barrel Sauna
SEE HOW ASSEMBLY WILL LOOK HERE.
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BARRELS
Installation guide
Barrel Nº51
Installation Guide

THERMORY 51 6 Person Barrel Sauna - Cover

51 6 Person Barrel Sauna

Everything you need to build your very own Thermory Barrel Sauna is right there in front of you. If it looks like a lot, it is. If it seems too complicated to assemble, it isn’t.
These instructions are speciﬁcally written to guide you through each step with ease. And if you need additional encouragement, you can scan the code on the back of this guide to see how it’s done.
The Thermory Barrel Sauna No51 is designed for up to four people. That’s plenty of room for you and the friends helping you put this together. But if you want to enjoy the ﬁrst steam all by yourself, we understand.

The Wait Is Over.
We truly appreciate the opportunity to share our love of sauna culture with you. And if there’s anything we can do to make your sauna experience better, please don’t hesitate to let us know. If not, just relax and enjoy.

PARTS 1

THERMORY 51 6 Person Barrel Sauna - Product Overview 1

PARTS 2

THERMORY 51 6 Person Barrel Sauna - Product Overview 3

STEP ZERO

Before you begin, be sure the sauna will ﬁt in your chosen location.
Approximately L x W x H of 8’ x 7’ x 7’ is ideal. Overall dimensions are shown here.
Be sure the site is level and free of standing water after rainfall.
Concrete, pavers or crushed stone is preferred.

STEP ONE
Measure support cradles (A) diagonally from corner to corner.
Measurements “a” and “b” should be equal to ensure the cradles are square.
Be sure cradles remain level.

THERMORY 51 6 Person Barrel Sauna - Product Overview 4

STEP TWO
Place the support cradles (A) on level site. The middle support cradle will have no dowel. Carefully level for better stability.
Place the center stave (B) on wooden dowels embedded in outer support cradles (A).
Fix the center stave (B) with screw 4.2×70 (N).
THERMORY 51 6 Person Barrel Sauna - Product Overview 5 STEP THREE
Place 6 sauna body staves (C) to each side of the center stave (B) and ﬁx with screws 4.2 x 70 (N).
Be sure to align the panel groove on every next body stave.

STEP FOUR
Place front panel with sauna doors (F2) and rear panel (E2) into the trimmed grooves. Be sure each panel is centered, leveled, and completely seated into the floor panel.
Bind these panels together by temporarily placing one or two body stave (C) on top of them. STEP FIVE
Two front side panels (F, F1) attach to the front panel (F2) and two back side panels (E, E1) attach to the rear panel (E2) by 4 screws 5.0 x 120 (M) and 4 stainless steel screws 4.20 x 70 (N1).
Be sure the bench supports face the interior of the sauna.
Conﬁrm that the combined width of the rear wall (E, E2, E1) matches the combined width of the front wall (F, F2, F1).
THERMORY 51 6 Person Barrel Sauna - Product Overview 8 STEP SIX
Continue placing body staves (C) tightly on both sides of the sauna using rubber mallet, while ﬁxing body staves on the front panel with 4.2 x 70 screws and rear window panel with 4.0 x 50 screws to prevent glass breakage.
To ﬁnish the roof top joint, use top stave (H).
THERMORY 51 6 Person Barrel Sauna - Product Overview 9

STEP SEVEN
Install steel bands (I) by wrapping bands around barrel prior to connecting with bolts and nuts (U).
Place steel bands evenly around barrel, covering screw heads.
Measure from steel band to barrel edge to ensure the steel band is even.
Cover roof with roof tape.
Rub and smooth with pressure to ensure adhesion.
Install interior aspen roof trim (O) with 4.0 x 50 (P1) stainless steel screws.
THERMORY 51 6 Person Barrel Sauna - Product Overview
10 STEP EIGHT
Attach bench supporting leg (J1) to the bench (J), install two sauna benches on wall mounts using stainless steel screws 4.2 x 70 (N1).
Hold the seat and leg assembly tight to the sauna wall. Using a level, make sure the bench seat is level from front to back. This will ensure proper placement.
Install backrests (J2) at your chosen height using stainless steel screw 4.0 x 50 (P1).
THERMORY 51 6 Person Barrel Sauna - Product Overview
11 STEP NINE
Flooring duckboards (L) can be used for wiring runs, conﬁrm speciﬁc wiring runs needed for chosen stove.
STEP TEN
Place waterproof roof cover (Z) and ﬁx it with wooden slat (Z1) and screws 4.0 x 50 (P).
Install front and rear decorative roof ﬁnishing boards (W), ﬁxing by screws 4.0 x 50 (P). THERMORY 51 6 Person Barrel Sauna - Product Overview
13