maytronics BASIC 1 Robotic Pool Cleaner Installation Guide
- July 9, 2024
- maytronics
Table of Contents
- maytronics BASIC 1 Robotic Pool Cleaner Installation Guide
- Robotic Pool Cleaner BASIC 1
- INTRODUCTION
- SPECIFICATIONS
- Power Supply
- WARNINGS AND CAUTIONS
- Warnings
- Cautions
- POOL CLEANER PARTS
- USING THE POOL CLEANER
- Set Up
- Putting the Pool Cleaner into the pool
- Removing the Pool Cleaner from the pool
- Maintenance
- Cleaning the filtration system:
- Unplug the power supply.
- Cable
- Off-season storage
- Read More About This Manual & Download PDF:
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
maytronics BASIC 1 Robotic Pool Cleaner Installation Guide
Robotic Pool Cleaner BASIC 1
Operating Instructions
INTRODUCTION
Thank you for purchasing a Maytronics Pool Cleaner.
We are sure that your Maytronics Robotic Pool Cleaner will provide you with
reliable, convenient and cost effective pool cleaning. Its reliable filtration
in all pool conditions and all-surface climbing brush enhance maximum pool
hygiene.
The Robotic Pool Cleaner by Maytronics deliver advanced cleaning technologys,
long lasting performance and easy maintenance.
SPECIFICATIONS
Motor protection: IP 68 Minimum depth: 0.80m / 2.6ft Maximum depth: 5m / 16.4ft
Power Supply
Digital “Switch-Mode” Power Supply
- Input – 100-250 AC Volts
- 50-60 Hertz
- 180 Watt
- Output – <30 VDC
- IP 5
WARNINGS AND CAUTIONS
Warnings
- Use the originally supplied power supply only
- Ensure the electrical outlet is protected by a ground fault interrupter (GFI) or an earth leakage interrupter (ELI)
- Keep the power supply out of standing water
- Position the power supply at least 3m / 10ft away from the edge of the pool
- Do not enter the pool while the pool cleaner is working
- Unplug the power supply before servicing
Cautions
Use the Pool Cleaner in the following water conditions only:
Chlorine | Max 4 ppm |
---|---|
pH | 7.0 – 7.8 |
Temperature | 6 – 34°C / 43-93°F |
NaCl | Maximum = 5000 ppm |
POOL CLEANER PARTS
Robotic Pool Cleaner BASIC 1
Brushes
There are three types of optional brushes, each designed to provide optimal traction on different pool surfaces. Only one type set is provided with your robot Pool Cleaner.
Filtration
There are two options of filtration system: filter bag or cartridge. Only one system type is provided with your robot pool cleaner.
Power Supply Unit
USING THE POOL CLEANER
Set Up
Position the power supply so that it is approximately in the middle of the
long sideof the pool at a distance of 3m / 10ft.
Attach the floating cable to the power supply by inserting it with the notch
on the connector (1) lined up withthe groove in the socket on the power supply
and turning clockwise (2).
Putting the Pool Cleaner into the pool
If Wonder (foam) brush/ Wonder rings are dry, soak them in water until soft.
Shake the Pool Cleaner from side to side or turn it upside down to release
trapped air. Let it sink to the pool floor.
Turn the power supply ON.
Removing the Pool Cleaner from the pool
The Pool Cleaner will perform automatic shut-off at the end of the cleaning
cycle.
Turn OFF and unplug the power supply.
Using the floating cable, bring the Pool Cleaner to the pool’s edge.
DO NOT PULL THE POOL CLEANER FROM THE POOL USING THE CABLE.
Maintenance
Cleaning the filtration system:
Cleaning the filter bag
Unplug the power supply.
Turn the Pool Cleaner upside-down. Open the bottom lid.
Remove the filter bag.
Clean the filter bag with a hose.
We recommend that you periodically wash the filter bag in a washing machine
using the gentle cycle program.
Periodically clean the brushes with a hose.
Robotic Pool Cleaner BASIC 1 | Operating Instructions
Cleaning the cartridge filters
Note: Don’t let the cartridge filters dry out before cleaning.
Unplug the power supply.
With the pool cleaner upside down open the bottom lid and pull it out.
Open the clips and remove the filters.
Insert the filters with the plastic backing facing out.
Insert the cartridge unit.
Cable
To remove the kinks, stretch the cable out completely and let it sit for at least a day in the sun.
Off-season storage
**** If the pool cleaner will not be in use for an extended period, perform the following storage steps:
- Make sure that no water is left in the pool
- Thoroughly clean the filter bag or cartridge and insert in
- Roll up the cable so that it has no
- Store the Pool Cleaner in a protected area upsidedown (not on its brushes).
Robot Nettoyeur de piscine BASIC 1 Instructions d’opération