JBC B1510 Grip Fitters Instruction Manual

: July 7, 2024
: JBC

JBC B1510 Grip Fitters

Specifications

Product Reference: BN-A
Includes: Grip Fitters (2 units), Manual (1 unit Ref. 0033729)
Additional Items (Not included, sold separately): PDS Portable Display 7, Bluetooth Connection, USB Cable, C115 Cartridge, USB Connector, Power Socket

Product Usage Instructions

Safety Guidelines:
Before using the product, read the manual thoroughly to understand the safety guidelines.
Note: The tool remains operational when batteries are charged, even if the display is off and the charging base is disconnected from the mains.

Turning Off/On:
The tool turns off automatically under specific conditions as mentioned in the manual. It can also be manually switched off/on by tapping the power button on the display.

Inserting Cartridges:
For C115 Cartridges:
Push cartridges inside the handle until the reference ring rests against the sealing plug.

Cartridge Adapter:
If using C115 Cartridges with smaller diameters, use adapters to store them in the cartridge holder. Insert the adapters into the slots of the cartridge holder from above.

Cartridge Exchanger:
For both C115 and C210 cartridges:

The cartridge exchanger allows safe insertion/change of cartridges without switching off the tool.
Cartridges are held securely in place by retention clamps.

Charging:
To charge the tool:

Place the tool in the charging holder to initiate charging. A beep will indicate proper placement and charging status.
Adjust the volume using the left button on the display if needed.

FAQ

Can C115 Cartridges be used with this product?
Yes, C115 Cartridges can be used with this product. Use the provided adapters for proper storage in the cartridge holder.
How do I know when the tool is charging correctly?
When the tool is placed in the charging holder, a beep will sound to indicate that it is properly placed and charging. You can adjust the volume using the left button on the display.

Packing List

The following items are included:

Important

Please read this manual and its safety guidelines thoroughly before using the product.
Note: Even if the display is turned off and the charging base is disconnected from the mains, the tool remains operational as long as the batteries are charged, even when the cartridge is taken out
The tool turns off automatically only under the following conditions:
- The tool is out of the charging holder (without the safety cap on) and remains completely still for 5 minutes.
- The tool has the safety cap on and remains completely still for 60 minutes.
The tool can be manually switched off and on by tapping the tool power button on the display.

Connection with B·IRON Station

Features

B·NANO performs up to 120 SMD soldering joints per charge and is the ideal tool for applications in laboratories or performing individual soldering jobs that require the highest precision in hard-to-reach areas. Note: To charge the tool a B·IRON station is needed.

Compatible Cartridges*

B·NANO Handle works with C115 Cartridges. Find the model that best suits your soldering needs at www.jbctools.com.

Inserting C115 Cartridges

Push the cartridges inside the handle until the reference ring rests against the sealing plug.

C115 Cartridge Adapter (B0643)

Since C115 Cartridges have a smaller diameter than C210 Cartridges, adapters must be used to store them in the cartridge holder. These adapters must simply be inserted from above into the slots of the cartridge holder.

Cartridge Insertion and Tool Charging

Cartridge Exchanger

The cartridge exchanger allows to insert/change cartridges safely without switching the tool off. Cartridges are held in place thanks to the retention clamps (1).
The exchanger is suitable for C115 and C210 cartridges.

C115 Cartridges
The holding area of C115 Cartridges is delimited by the two rings at the cartridge shaft (x).

Cartridge Inserting
Place the tool over a cartridge and press the tool down to insert the cartridge (1). To release the tool with the cartridge inserted from the extractor, lift the tool upward (2).

Cartridge Fixing
Gently press the tip against the holes on the sides of the cartridge exchanger (1) to ensure that the cartridge is appropriately inserted.

Tool Charging
Place the tool in the charging holder (1) to charge it. A beep will sound when the tool is properly placed and charged. The volume can be adjusted using the left button on the display.

Important: Charge the tool completely before using it for the first time.
A full charge takes:

30 min for B·100
60 min for B·500
30 min for B·NANO
40 min for B·TWEEZERS
Note: Cartridges must be inserted up to the mark for a proper connection and function.

Tool Connection

Make sure that the charging base is connected to the mains.
Note: The supplied tool is already connected.

Scanning another tool: (This process can take a while)

Place the tool in the charging holder to activate it.
The status light band color indicates the charge level (see table below).
If the scanning process does not run automatically, tap “scan” (6) on the display while the tool remains in the charging holder. When the tool is shown in the device list on the display, select it (11) and tap “connect” (7). Now the tool is ready for soldering.

Tool search function:
When in doubt of which tool corresponds to the tool’s name, use the tool search function. Tap on the magnifying glass symbol (8) next to the tool’s name. The light band on the corresponding tool blinks in blue for five seconds to identify it.

Working with two tools (works also for charging bases with only one charging holder):

It is possible to connect up to two tools at the same time. If a tool is already connected, first disconnect it from the device by selecting “Menu” (9) and tapping on “Disconnect”.
Place the second tool in the charging holder and scan it (6). The second tool is also shown in the device list on the display (10). To work with two tools, select one from the left-hand column (11) and the other one from the right-hand column (10). Then tap on “connect” (7).

Status Lightband
The status light band on the tool indicates its status (see table on the right).

Color	Tool Status
Green	More than 50% charged
Orange	Between 20% and 50% charged
Red	Less than 20% charged
Green blinking	Charging

(more than 50% charged)

Orange blinking| Charging

(between 20% and 50% charged)

Red blinking| Charging

(less than 20% charged)

No color| Safety cap on the handle and/or power off
Blue blinking|

The locate Tool function activated

Operation

Thanks to the intelligent heat management, the cartridge tip recovers temperature extremely quickly.
This allows reducing the tip temperature when the device is not in use, resulting in a longer tip lifespan.
When the tool enters Sleep (1) or Hibernation (2) Modes, the tip temperature lowers automatically below the solder-melting-point temperature.

Tool Status and Tip Temperature

The tool can go into several statuses under different circumstances (see the diagram on the next page). Depending on the status, the cartridge tip reaches different temperatures:

Tool Status	Tip Temperature
Sleep & charging	Cools down to the set Sleep temperature. Selectable between

70 °C and 150 °C.
Hibernation & charging| Cools down to room temperature.
Working| Heats up to the set work temperature.
Resting without cap| Cools down to room temperature (after 5 minutes of being completely still).
A tool with a cap on| Cools down to room temperature.
Hibernation| Cools down to room temperature.
Shut off| Remains at room temperature (tool is shut off).

Sleep & Charging
Sleep Mode can be activated/deactivated (2). If it is activated and the tool is placed in the charging holder, in addition to charging, the tip temperature cools down to sleep temperature.

Hibernation & Charging
If Sleep Mode is not activated and the tool is placed in the charging holder, besides charging, it goes into Hibernation and the tip temperature cools down to room temperature.

Work
When the tool is taken out of the charging holder while in Sleep (1) or Hibernation (2) Modes, the cartridge tip heats up to the set work temperature and the tool is ready to use (3).

Hibernation
The tool goes into Hibernation Mode in two different cases:

After working, when the tool is laid down (4) and is resting between 5 and 10 seconds (time is adjustable).
After working, when placing the cap on the tool (5).
Note: Before the tool enters Hibernation Mode, it can be picked up to work with it and the cartridge tip heats up to work temperature.

Auto Shut-off
The tool shuts off automatically in two different cases:

When the tool (without the tool cap) is laid down and remains completely still in Hibernation Mode for 5 minutes (6).
When the tool (with the tool cap on) remains completely still in Hibernation Mode for 60 minutes (7).

Tool Reactivation
Once the tool has automatically shut off, place it back in the charging holder (8) to reactivate it (see diagram on previous page).

Manual Tool Shut-Off
Besides the “automatic shut-off” feature, the tool can also be manually switched off by tapping the tool power button on the display. When it is switched off, the cartridge cools down to room temperature.
Note: To switch the tool back on, tap the same button on the display.

Safety Cap

Safe Tool Transportation

Thanks to the tool’s safety cap, B·IRON tools can be carried around safely, even with the cartridge inserted.
When the cap is placed onto the tool, it goes into Hibernation Mode immediately and the cartridge tip cools down to room temperature.
Note: The purpose of the cap is to allow safe transport, not storage.

Safety Cap Holder

While the tool is in use, the safety cap can be stored on the cap holder located on the back of the charging base.
There is space for two caps.

JBC Software

The app is already installed on JBC’s B·IRON Display. If another display is to be used, the app must be downloaded to the corresponding display (see chapters below).
At the moment of purchasing the B·IRON tool, the current firmware is already downloaded to the tool.
Note: Since the tool firmware is not updated automatically, updates must be carried out by the customer. To do so follow the instructions on the next page.

App Versions

If an app with version 1.6 or higher is already installed on the display (tablet or smartphone) used with B·IRON, the firmware of the tool can be updated directly without updating the app. Carry out the steps described in section “B·IRON Tool Firmware Update”.
Older app versions must be updated. If no app has been installed, it must be installed first.

App Installation

On JBC’s portable display (Android), the B·IRON app is already installed.
On the user’s smartphone or tablet (Android / iOS), go to the App Store/Play Store and search for “JBC B.IRON” on the search bar. Note: An Internet connection is required to download the app.

App Update

Display with Internet connection (Android / iOS)
Update the app via Google Play (Android) or the App Store (iOS).
Display without Internet connection (Android)
- Download JBC’s installer program to another device with an Internet connection from JBC’s website: https://www.jbctools.com/jbcsoftware.html
- Then copy the downloaded program to the internal storage of the display used with B·IRON. Access the internal storage of the display and run the downloaded program. Once the program is completed, the app will be updated to its newest version.
  Note: For JBC´s displays, swipe down to open the internal storage folder.

Downloading the Tool Firmware Update File

Display with internet connection:
Download the firmware update file to the display used with B·IRON from: https://www.jbctools.com/jbcsoftware.html. Go to the internal folder and unzip the downloaded file.

Display without internet connection:

Download the firmware update file to another device with an internet connection from JBC’s website: https://www.jbctools.com/jbcsoftware.html and unzip the downloaded file.
Then do as described in the table.
PDS

JBC’s display (android)

|

Other android devices

|

iOS devices

---|---|---
Copy the unzipped files on the device used with B·IRON:
Folder:| Folder:| Path:
\Internal shared storage\Android\data\ es.infinitysource.jbc_ soldering.JBCBiron\files|

\Internal shared storage\ Android\data\com. JBC tools.jbcbiron\files

| Files > On my iPad > JBC B.iron

Executing the Tool Firmware Update File

Tool firmware updates are not executed automatically; they must be carried out by the user.
On the display you are using with the B·IRON, and the latest app version installed, access the B·IRON app:
Select the tool you want to update. Then in the main menu select “update”.
Note: At least one tool must be linked to see the expanded menu options.
If the downloaded tool firmware update file contains a newer version than the one already installed, the current and new versions are displayed (1). Tap “Update” to start the update (2).
The update process takes about 10 minutes.
The B·IRON status light continuously changes its color during the update process.
Once the update is completed, “Tool updated” (3) will be displayed.
If “No new version available” is displayed (4), no update is possible or required.

Maintenance

Replacing B1510 Grips (Soft Foam)

Inserting Fitters
Insert the fitters into the new grip.
Assembling Grips
Push the grip with the fitters onto the handle.
Removing Fitters
To remove the fitters, hold the grip and pull the fitters out. Use pliers if necessary

Replacing Sealing Plugs
The sealing plug prevents undesirable flux vapors or particles from entering the handle and its usage is highly recommended. If the sealing plug is not used, this can lead to incorrect cartridge contact and may render the tool unusable.
Note: Check the condition of the plug periodically and replace it as soon as wear or cracking is detected.

Sealing plug references:

Replacing Sealing Plug OB4000
For B115 handles, the use of the OB5000 sealing plug is mandatory. Without the use of the sealing plug, the cartridges cannot be properly inserted.

Remove the worn sealing plug by unscrewing it by hand.
Position the chamfered side upwards and screw the new sealing plug into the handle bushing until it stops.
Make sure the sealing plug is placed correctly.
The shoulder of the plug must be in touch with the bushing.

Maintenance – Station and Tools

Before carrying out maintenance, always extract the cartridge from the tool and disconnect the charging base from the mains. Allow the equipment to cool down.

Use a damp cloth to clean the casing and the tool. Alcohol can only be used to clean the metal parts.
Periodically check that the metal parts of the tool and charging holder are clean so that the charging works properly.
Keep the tip surface clean and tinned before storage to avoid tip oxidation. Rusty and dirty surfaces reduce heat transfer to the solder joint.
Do not use liquids such as alcohol, thinner, or benzene to clean the portable display.
Repairs should only be performed by a JBC-authorized technical service.

Battery

It is imperative to follow safety guidelines to prevent electric shock, injury, fire, or explosion.

Caution: This product contains lithium-ion batteries. Mishandling or improper use may result in fire, explosion, or personal injury.
Always use the provided charger. Do not use damaged chargers or batteries.
Never attempt to disassemble or modify the batteries or the product. Doing so may lead to electric shock, fire, or damage to the product.
In the event of damage, leakage, or overheating of the batteries, discontinue use immediately and contact customer support or JBC technical service facility.
Dispose of devices with batteries inside, responsibly according to regulations. They must be disposed of by local regulations so that they can be recycled.
Do not throw devices with batteries into household waste and do not dispose of them in fire or water.

Safety

It is imperative to follow safety guidelines to prevent electric shock, injury, fire, or explosion.

Do not use the units for any purpose other than soldering or rework. Incorrect use may cause a fire.
The power cord must be plugged into approved bases. When unplugging it, hold the plug, not the wire.
Do not attempt to dismantle or open the housing of the tool as it may cause damage.
Do not work on electrically live parts.
The tool should be placed in the charging holder when not in use to charge the batteries.
The soldering tip, the metal part of the tool, and the charging holder may still be hot even when the station is turned off.
Do not leave the tool unattended when it is on.
Avoid flux coming into contact with skin or eyes to prevent irritation.
Be careful with the fumes produced when soldering.
Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working to avoid personal harm.
Utmost care must be taken with liquid tin waste, which can cause burns.
This appliance can be used by children over the age of eight and also persons with reduced physical, sensory, or mental capabilities or lack of experience provided that they have been given adequate supervision or instruction concerning the use of the appliance and understand the hazards involved. Children must not play with the appliance.
Maintenance must not be carried out by children unless supervised.
Do not expose the portable display to high temperatures, humidity, or dust. Avoid direct sunlight.
Do not drop the portable display or the tool, as it may cause damage or malfunction.
Do not disconnect your device when it is in ﬁ le transfer mode.
Do not use the portable display in places where wireless communications are restricted.

Specifications

Peak Power (Tool): 15 W
Battery: Li-Ion 7.4 V / 180 mAh
Charge Time: 15 minutes
Selectable Temperature: 100 – 450 °C / 210 – 840 °F
Idle Temp. Stability (still air): ±1.5 °C / ±3 °F
Temp. Accuracy: ±3% (Using reference cartridge)
Connections: Bluetooth Low Energy (BLE)
Ambient Operating Temp: 10 – 50 °C / 50 – 122 °F
Total Net Weight: 66 g / 0.15 lb
Total Package Dimensions/Weight: 220 x 75 x 30 mm / 110 g (L x W x H ) 8.66 x 2.95 x 1.18 in / 0.24 lb

Warranty

JBC’s 2-year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labor.
Warranty does not cover product wear or misuse. For the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased.