Rankam HU2220401-GW 300Lb Cube VP Feeder Installation Guide

: July 6, 2024
: Rankam

Rankam HU2220401-GW 300Lb Cube VP Feeder

NOTE : Before beginning assembly of the product, make sure all parts are present. Compare parts with the package content list and hardware contents. If any part is missing or damaged do not attempt to assemble the unit. Contact customer service for replacement parts

Warnings

PAY ATTENTION to these statements when reading this manual and the information contained can save your life.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING: Be alert to the possibility of serious bodily injury if the instructions are not followed. Be sure to read and carefully follow all of the messages.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
Your GAME WINNER 300LB CUBE VP FEEDER IS DESIGNED, ENGINEERED AND CONSTRUCTED IN A MANNER THAT MAKES IT A RUGGED PIECE OF HUNTING EQUIPMENT THAT WILL GIVE YOU YEARS OF SERVICE. THIS RUGGED CONSTRUCTION MAKES YOUR FEEDER PHYSICALLY HEAVY. AS SUCH, YOU SHOULD NEVER ATTEMPT TO ASSEMBLE THIS FEEDER ALONE. YOU MUST HAVE A MINIMUM OF TWO (2) ADULTS FOR THE SAFE ERECTION OF YOUR FEEDER. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH!
THIS FEEDER MUST BE ERECTED ONLY ON FIRM AND LEVEL GROUND. BEFORE FILLING THE HOPPER, RECOMMEND INSTALLING FOUR (4) STAKES (PART #11). FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH!

REFER TO THE IMAGES IN THIS MANUAL FOR VISUALIZATION OF THE ASSEMBLY PROCESS IN ADDITION TO READING THE INSTRUCTIONS.SOME PARTS MAY CONTAIN SHARP EDGES, SHARP POINTS, OR EDGES THAT CAN SCRATCH, POKE, OR PUNCTURE. WEAR APPROPRIATE CLOTHING AND SAFETY GLOVES DURING ASSEMBLY. THIS UNIT IS HEAVY. DO NOT ASSEMBLE WITHOUT ANOTHER ADULT. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH! PRIOR TO ATTEMPTING TO USE THIS UNIT, TAKE A MOMENT TO BECOME FAMILIAR WITH THE ASSEMBLY, SETUP AND INSTALLATION. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH!

Warnings

DO NOT USE THIS UNIT AROUND POWER GENERATING EQUIPMENT (TRANSFORMERS, GENERATORS, SUBSTATIONS, ETC) AND/OR TRANSMISSION EQUIPMENT (POWER LINES). FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH!
DO NOT LOAD THE FEEDER WITHOUT ANOTHER ADULT. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH!
DO NOT LOAD THE FEEDER UNDER AND/OR DURING BAD WEATHER SUCH AS STORMS, SNOW, LIGHTNING OR THUNDERSTORM. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULTS IN SERIOUS INJURY OR DEATH!
DO NOT SIT OR STAND ON OR INSIDE THE HOPPER. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH!
DO NOT LOAD OVER 300 POUNDS OF FEED. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS DAMAGE TO THIS UNIT.
DO NOT LOAD THE FEEDER UNTIL IT IS COMPLETELY ASSEMBLED AND STANDING UP IN PLACE.
DO NOT STORE OR HANG ITEMS ON THE HOPPER. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS DAMAGE TO THIS UNIT.
DO NOT DISASSEMBLE AND/OR REMOVE PARTS WITHOUT ANOTHER ADULT PRESENT. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH!
DO NOT ASSEMBLE, DISASSEMBLE, AND/OR REMOVE PARTS FROM THE FEEDER UNDER AND/OR DURING BAD WEATHER SUCH AS STORMS, SNOW, LIGHTNING, OR THUNDERSTORMS. FAILURE TO FOLLOW THESE INSTRUCTIONS
MAY RESULT IN SERIOUS INJURY OR DEATH!
THE 6V RECHARGEABLE BATTERY (NOT INCLUDED) SHOULD HAVE A COMPLETE CHARGE PRIOR TO THE FIRST TIME OF OPERATION. REFER TO THE USER INSTRUCTIONS OF THE BATTERY.
THE PROPER SPACING BETWEEN THE SPIN PLATE AND THE FUNNEL IS 3/8 INCH. THIS IS VERY IMPORTANT FOR SERVICE FREE OPERATION.

Warnings

TO TEST YOUR FEEDER FOLLOW THE INSTRUCTIONS IN THE TIMER MANUAL. DO NOT TEST FEEDER WHEN IT CONTAINS FEED. TEST FEEDER WHEN EMPTY ONLY! TESTING THE FEEDER WHILE IT CONTAINS FEED WILL CAUSE FEED
TO BE DISCHARGED AT A HIGH VELOCITY AND COULD RESULT IN BODY INJURY. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH!
THOROUGHLY INSPECT THE FEEDER PRIOR TO EACH USE FOR SIGNS OF WEAR, ROT, CORROSION, CRACKS, DETERIORATION AND/OR ANY OTHER TYPE OF DEFECT. DO NOT USE THIS FEEDER IF IT SHOWS EVIDENCE OF WEAR, ROT,
CORROSION, CRACKS, DETERIORATION AND/OR ANY OTHER TYPE OF DEFECT. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH. DO NOT REMOVE, MODIFY AND/OR OMIT ANY PART OR
OTHERWISE MECHANICALLY MODIFY THIS UNIT OR ITS ASSEMBLY IN ANY MANNER. MODIFICATION, OMMISSION AND/OR PART SUBSTITUTION MAY RESULT IN SERIOUS INJURY OR DEATH!

OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:

THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE.
THE DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

BEFORE STANDING UP THE FEEDER, YOU MUST

CHECK ALL HARDWARE TO BE SURE IT IS IN PLACE AND TIGHT.
CHECK ALL BOLTS AND NUTS TO BE SURE THEY ARE FIRM AND TIGHT.
DO NOT THROW AWAY THE PACKAGING MATERIAL AT THIS TIME.

Warnings

IMPORTANT!

THE MANUFACTURER OF THE 300-LB CUBE VP DEER FEEDER IS NOT RESPONSIBLE FOR ANY INACCURATE INFORMATION YOU HAVE RECEIVED REGARDING STATE FEEDING REGULATIONS. PLEASE ALWAYS KEEP YOUR INFORMATION UP-TO-DATE AND RELIABLE. MANY STATE LAWS CHANGE AND ARE AMENDED WITHOUT NOTICE. ALWAYS DOUBLE-CHECK YOUR STATE AND SPECIFIC COUNTY FEEDING LAWS REGARDING THE USE OF FEEDERS.\

Tools Required

(not included)

Parts List

Components are packed INSIDE the Timer Kit Set package!!

Hardware List

Hardware is packed INSIDE the Timer Kit Set package!!

Product Diagram

Assembly Instructions

Step 1:

Attach Mounting bracket
(#15) to the Metal Timer kit Housing (#18) using bolts (K, M6x20), flange nut (N, M6), washer (L, 6mm) and butterfly nuts (M, M6). Wing Bolt (R) to secure door. (All hardware is packed inside the Timer Kit unit).

Hardware:

K – 2 pcs
L – 2 pcs
M – 2 pcs
N – 2 pcs
R – 1 pc

Step2:

Hardware :

K – 8 pcs

Attention: the conduit connector on the side of the timer box and the conduit connector at the bottom of the hopper should be on the same side for proper spacing of spinner plate to the funnel (3/8”)

Step 3:
Attach Wire Conduit (#13) inside the hopper and at the bottom of the hopper per the diagram. Long conduit – connects to compartment in hopper and bottom of hopper Short conduit – connects to timer housing and bottom of hopper Blue and White wires from Digital Unit (#14) pass through conduits and connect to motor in Metal Timer Kit Housing

Step 4:
Attach the Varmint Guard (#12) to the bottom of the hopper using bolts (B, M6x20) and flat washers (E, 6mm).

Hardware:

B – 8 pcs
E – 8 pcs

Step 5:

Attach Upper Legs (#7) to the hopper using bolts (A, M8x15), flat washers (D, 8 mm) and locking nuts (C, M8). DO NOT TIGHTEN bolts and nuts in this step.

Hardware:

A – 16 pcs
C – 16 pcs
D – 32 pcs

Step 6:

Attach Lower Legs (#8) to Upper Legs (#7) using bolts (A, M8x15), flat washers (D, 8 mm) and locking nuts (C, M8). DO NOT TIGHTEN bolts and nuts in this step.

Hardware:

A – 16 pcs
C – 16 pcs
D – 32 pcs

Step 7:

Attach Leg Blades (#9) to legs using bolts (A, M8x15), flat washers (D, 8mm) and locking nuts (C, M8). DO NOT TIGHTEN bolts and nuts in this step.

Hardware:

A – 4 pcs
C – 4 pcs
D – 8 pcs

Step 8:

Assemble Leg Skid Blades (#10A & #10B) using bolts (A, M8x15), flat washers (D, 8mm) and locking nuts (C, M8). DO NOT TIGHTEN bolts and nuts in this step.

Hardware:

A – 4 pcs
C – 4 pcs
D – 8 pcs

Step 9:

Attach the Leg Skid Blade in the previous step to the legs using bolts (A, M8x15), flat washers (D, 8mm) and locking nuts (C, M8) TIGHTEN ALL bolts and nuts now including the hardware in Step #5,6,7,8

Hardware:

A – 4 pcs
C – 4 pcs
D – 8 pcs

Step 10:

Attach Rain Diverter (#4a) and Gasket (#4b) to the hopper (above door) using bolts (B, M6x20)

Hardware :

B – 5 pcs

Step 11:

Attach Lid (#1) to the hopper following the diagram. Tighten all bolts and nuts and affix the feeder to the ground with 4 ground stakes (#11) before use. Your feeder assembly is completed.

HOW TO LOAD YOUR FEEDER

OPEN THE LID AND POUR FEED INTO THE HOPPER. AFTER FILLING, CLOSE THE LID. TIPS & POINTERS:

(Q) What kind of feed should I use?
(A) Whole kernel corn is recommended. Whole kernel corn mixed with soybeans or pellets is also effective for attracting deer. NOTE: When not
mixed with corn, some types of pellets can take on moisture and clog the feeder

HOW TO INSTALL BATTERY

REMOVE TIMER KIT COVER AND INSTALL A 6V RECHARGEABLE
BATTERY (NOT INCLUDED) BY ATTACHING RED ALLIGATOR CLIP
TO THE POSITIVE TERMINAL (+) AND BLACK ALLIGATOR CLIP TO THE NEGATIVE (-) TERMINAL

HOW TO OPERATE THE TIMER

READ THE OPERATION MANUAL INCLUDED IN THE TIMER KIT UNIT. THE PROPER SPACING BETWEEN THE SPIN PLATE AND THE FUNNEL IS 3/8 INCH (0.953 cm). THIS IS VERY IMPORTANT FOR SERVICE-FREE OPERATION.

Care and Maintenance

INSPECT THE FEEDER FOR ANY LOOSE PARTS OR HARDWARE REGULARLY
CHECK IF THE FEEDER IS TAKING WATER ON RAINY DAYS. SEAL GAP WITH SILICONE SEALANT IF NECESSARY
IF RUST APPEARS ON THE EXTERIOR SURFACE OF THE FEEDER, CLEAN AND BUFF THE AFFECTED AREA WITH STEEL WOOL OR FINE GRIT EMERY CLOTH. TOUCH-UP WITH A GOOD QUALITY PAINT
STORE FEEDER INDOORS WHEN NOT IN USE
CLEAN FEEDER HOPPER REGULARLY TO AVOID CLOGGING AND DAMAGE TO THE CONTROL UNIT

ATTENTION

IF USING THE GAME-WINNER TIMER AS A REPLACEMENT TIMER, IT

WILL WORK WITH EITHER 6V OR 12V MOTORS. IF USING A 6V MOTOR, USE A 6V BATTERY. IF USING 12V MOTOR, USE A 12V BATTERY. ** GAME WINNER MOTORS ARE 6V. **

Assembly Instructions of 155060 Game Winner 6V Solar Panel Charger (not included)

Step 1:

Attach the Game Winner Solar Panel Charger directly to the hopper panel using bolts (SP3, M6x20).
Note : It is recommended to install a Solar Panel before loading or when it is empty.

Hardware : #SP3 – 2 pcs

For use of NON-Game Winner Solar Panel Charger (not included), follow the below instructions

Attach the Solar Panel Fixture Bracket (#17) on side of hopper using bolts (SP3, M6x20).

Hardware : #SP3 – 2 pcs

Attach NON-Game Winner Solar Panel Charger to Solar Panel Fixture Bracket using bolts (SP1, M5x12) and nuts (SP2, M5).

Non-Game Winner 6V Solar Panel Charger Assembly (not included)

Hardware: #SP1 – 2 pcs #SP2 – 2 pcs

Step 2:

With a knife, make an incision to each of the rubber gaskets so that the wire conduit can be inserted into hopper and through the hole into the compartment.

Warranty

Warranty Information

The manufacturer warrants this Product to be free from defects in workmanship and materials for a period of 90 days from the date of purchase, PROVIDED claims are submitted, in writing, with proof of purchase.
If any part of this item fails because of a manufacturing defect within the Limited Warranty Period, Manufacturer offers to replace such part(s) provided that such parts have not been improperly repaired, altered, or tampered with or subject to misuse, abuse or exposed to corrosive conditions. This Limited Warranty is, however, subject to certain limitations, exclusions, time limits and exceptions (Hereinafter “Conditions”) as listed below. Read these Conditions carefully.
This Limited Warranty shall be limited to the replacement or repair of any part(s) which Manufacturer determines, after reasonable examination, to have been defective at the time of manufacturing and the manufacturer’s obligation(s) shall be limited to replacement, if any, of defective part(s) which shall be shipped at Original Purchaser’s expense to Original Purchaser’s designated shipping address.
This Limited Warranty is given to and covers the ORIGINAL PURCHASER ONLY and such coverage terminates 90 days from the date of purchase.
DAMAGE LIMITATION WARNING: IN NO EVENT SHALL MANUFACTURER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING (BUT NOT LIMITED TO) LOSS OF USE OF THE PRODUCT, LOSS OF TIME, INCONVENIENCE, EXPENSES FOR TRAVEL, TRANSPORTATION, LODGING EXPENSES, LOSS OF FOOD, LOSS BY DAMAGE TO PERSONAL PROPERTY OR LOSS OF INCOME, PROFITS OR REVENUE.
MANUFACTURER’S OBLIGATION: Manufacturer’s liability shall be limited to the delivery of a good, merchantable Product and, if necessary, the repair or replacement, at the manufacturer’s option, of any defective part or unit.
TRANSFER LIMITATIONS: This Limited Warranty is not assignable or transferable. It covers only the original purchaser.
RESERVED RIGHT TO CHANGE: The manufacturer reserves the right to make changes or improvements to products it produces in the future without imposing on itself any obligations to install the same improvements in the products it has previously manufactured.
This Limited Warranty gives the Original Purchaser specific legal rights but there may be other rights which vary by jurisdiction.
This warranty does not cover the following items:
Chips or scratches on porcelain or painted surfaces
Rust or corrosion is not deemed a manufacturing or materials defect
Discoloration or loss of paint due to handling during assembly, heat or cleaning products. Paint may require a touch-up.
Stainless steel discoloration or corrosion
Consumables such as batteries
Damages caused by wild game

IF CUSTOMER SERVICE IS NECESSARY:

The original purchaser is responsible for shipping and handling charges of the returned item(s) and replacement parts, if any.
All parts to be replaced will need to be shipped before replacement items will be sent.
Follow the customer service representative’s instructions exactly. If a return is necessary, it must be packed carefully and shipped prepaid. Should you encounter any problems obtaining replacement parts, CALL US FIRST. Do not return product to the store. WE CAN HELP