amazon basics B07J4HXZ6Q Door Lever User Guide

Door Lever
User Guide

B07J4HXZ6Q Door Lever

Shelby: BO7J4HXZ6Q, BO7J4HXKBG, BO7J4HXTM3, BO7J4VHWRK, BO7J4V9XGG, BO7JSMNSN4, BO7J4VQCB1, BO7JVPPJ1H, BO7J51DFVT, BO7J51F4JR, BO7J4VHWS6, BO7J4VNVR5
Manchester: BO07J51KQFM, BO7JSMV65R, BO07J51FKQD, BO7JSHH1K7, BO7J4V9Z8F, BO7JSMV65Z, BO7J4VHWT3, BO7JVP265Q, B07J51FKQX, BO7JSHR6Z2, BO7J4VHQWY, BO7J4VLXNL
Victorial: BO7JSMV66X, BO7J51L7FX, BO7JS1F4LL, BO7J51F4LP, BO7JSN33B1, BO7J4VQCD9, BO7J4VHQXZ, BO7JSHR71G, BO7J4VHVG9, BO7J51DNNL, BO7J4VK6YH, BO7JSMXK34
December: BO7J4VLVHN, B07J51DNNW, BO7J51DFZ8, BO7J4HXTQH, BO7JVPFT25, BO7JSHM9ORB, BO7J51DNPF, BO7J4VHVH7, BO7J4HXKGF, BO7JVPFFYV, BO7J4V9XM2, BO7JVP268G
Victory: BO7JVPFFZ4, B07J51DG1D, BO7JSHM9S2, BO7J51DG1L, BO7J5HR73D, BO7JSMV697, BO7JSMNSRV, BO7JSMRQTF, BO7J4VHWXG, B07J51KQL1, BO7J51DYHG, BO7JSMXK56
Straight: BO7JVPFG11, BO7J4VK71X, BO7JVP269Y, BO7JSMV6BF, BO7J4VDX8D, BO7J4VYRSZ, BO7J51RF6C, BO7J4VDX8M, BO7JSMXK63, BO7JVPPJ7R, BO7J51F4QH, BO7JVPPJ7X
Cambridge: BO7J4V9ZFM, BO7J4VHR2Z, BO7JVPPJ8C, BO7JVPPJSF, BO7J51F4QY, BO7J4VYRTX, BO7JSHRD8W, BO7J4V9XPZ, BO7JSHM38V, BO7JSHM38Y, B07J51DG4G BO7J5MV6D1

Tools Needed

Dvelivery Content

|
---|---
Latch (x1)| Drive-in collar (x1)
|
Latch face plate (x1)| Strike plate (x1)
|
Outer lever (x1)| Inner lever (x1)
|
Key (for entry lever) (x1)| Lever removal pin (x1)
|
Wood screws (x 4) ∅ 3/16’x15/16″ (4x24mm)| Machine screws ∅ 3/16″x3/4″ (∅ 4×19 mm) ∅

Important Safeguards

Read these instructions carefully and retain them for future use. If this productis passed toa third party, then these instructions must be included.

When using the product, basic safety precautions should always be followed to reduce the risk of njury including the following:

• For domestic use only.
• Make sure these instructions are read and completely unders tood before attempting installation. When in doubt, contact a professional installr for assistance.
• This product contains small parts that could be a choking hazard if swallowed. Keep children and pets away when installing the product,
• Do not use ths product if any parts are missing, damaged, or worn.
• Regularly examine the product for wear and tear. Stop using the product at first sign of damage or if parts become detached.
• Make sure these instructions are read and completely understood before attempting installation. When in doubt, contact a professional installe for assistance,
• No lock guarantees complete secuity. The lock may be compromised by force or technical methods. Locks are not a substitute for being aware of the property’s surroundings, exercising caution and using common sense. To minimize the risk of a breakcin and to enhance security, contact a professional locksmith or security expert.

Before First Use

DANGER Risk of suffocation!
Keep any packaging materials away from children and pets— these materials are a potential source of danger, e.q. suffocation.

• Remove all the packing materials.
• Remove and review all components before installation.
• Check the product for transport damages.

Installation

3.1 Determining door orientation

1. Face the exterior side of the door. Note the location of the hinges.
2. If the hinges are on the left, the door swings open from the left.
3. If the hinges are on the ight, the door swings open from the right.

3.2 Installing on new door
3.2.1 Drilling holes

1. Fold the template at the dotted line. Tape the template onto the interior side of the door between 34-48″ (86-122 cm) from the floor for the height of the doorknob (Fig. 1).
2. Measure the thickness of the door to determine the center point for the latch. Mark either the 1-3/4″ (44 mm) or 1-3/8” (37 mm) hole.
3. Mark either the 2-3/8” or 2-3/4” (60 mm or 70 mm) hole for the backset.
4. Drill a 2-1/8” (54 mm) hole through door face as marked for the lock body (Fig. 2).
5. Drill a 1” (25 mm) hole in the center of the door edge for the latch (Fig. 2). If installing a drive-in collar, drill a 31/32” (24.6 mm) hole.

3.2.2 Adjusting the backset

• The backseti preset at 2-3/8″ (60 mm), which s standard for most doors.
• Pull the spindle cam out from the latch to change the backset to 2-3/4″ (70 mm) (Fig. 3).
• Push the spindle cam back nside the latch to change the backset to 2-3/8″ (60 mm).
• Make sure the cams stay aligned in square shape (Fig. 4).

3.23 Installing the latch
NOTICE
If using the drive-in collar, it is not necessary to chisel the door edge for faceplate installation. Secure the drive-in collar onto the latch, then install the latch into the edge bore diretly. Make sure the bevel faces the outside assembly.
Attaching the latch face plate
Prior to installation, make sure that the face plate is appropriate for the latch.
Replace the face plate

1. Pry the face plate from the lock body with a flat head screwdriver (Fig. 5).
2. Align and press to snap the appropriate face plate onto the latch body (Fig. 5).

Install the drive-in collar (optional)
Align the drive-in collar to the head of the latch, then push to lock it into position (Fig. 6).

1. Insert the latch into the hole, keeping it parallel to the door face. Mark around the outside of the latch and the screw hole locations with a pencil then remove the latch (Fig. 7).
2. Chisel in the door to 5/32″ (4 mm) deep to allow the latch face to lie flush with the door edge (Fig. 8). Cut the area into small sections first.
3. Dril pilot holes over the marks for the 1/8″ (3 mm) wood screws.
4. Reinsert the latch into the hole. Make sure to position the flat sde of the atch facing the opening direction of the door.
5. Insert and tighten 2 wood screws through the latch plate (Fig. 9)
6. Optional: If using the drive-in collar, intall the latch with drive-in collar nto the edge bore directly (Fig. 10).

3.2.4 Installing the strike plate

1. Close the door until the latch assembly is partially inside the door jamb. Mark 2 lines on the door frame paralll to the top and bottom of the latch plate. Mark 1 horizontal line at the center of the strike plate instalation area (Fig. 11).
2. Measure half of the door’s thickness from the inner comer of the door jamb to determine the vertical center of the strike plate. Mark 1 vertical line at the center of the strike plate installation area.
3. Drill a 1″ (25 mm) hole that is 1/2″ (13 mm) deep at the intersection of the marked lines.
4. Center the screw holes over the vertical line. Draw around the strike plate and mark the positions of the screw holes.
5. Chisel in the door jamb to 1/16″ (1.6 mm) deep to allow the strke plate tole flush with the door jamb (Fig. 12). Cut the area into small sections frst.
6. Position the strike plate into the mortise. Drill pilot holes for the 1/8″ (3 mm) screws using adrill bit.
7. Insert and tighten 2 wood screws for the trike plate (Fg. 13).
8. Move the srike plate inward to tighten the it between the door and the door jamb. Chisel more if necessary.

3.2.5 Reversing the lever direction
NOTICE For entrance sets, make sure the levers are unlocked before reversing the evers.

1. For both levers, depress the lever catch through the hole of the trim collar using the handle pin. Pull the lever off (Fig. 14, Fig. 15).
2. Swap the inner and outer levers. For entrance sets, fit the cylinders on the outer and inner levers.
3. Push the levers until the lever catch clicks. Make sure the levers are securely in place.

3.2.6 Installing the outer lever assembly

• Align and insert the spindle of the outer lever through the latch. Press flush against the door (Fig. 16).
• For privacy sets, make sure the emergency release is in the correct position before installing the lever (Fig. 17).

3.2.7 Installing the inner lever assembly

1. Align and insert the innerliner onto the spindle of the outer lever.
2. Insert and tighten the 2 machine screws through the rose into the stems of the outer lever (Fig.18).

Cleaning and Maintenance

4.1 Cleaning

• Wipe with a soft, clean cloth.
• Never use corrosive detergents, wire brushes, abrasive scourers, metal or sharp utensils to clean the product.

4.2 Maintenance

• Periodically inspect the doorknob for any signs of wear or damage.
• Lubricate the doorknob if needed to maintain proper functionality.
• Replace the doorknob promptly if it becomes worn-out to prevent risk of security incidents.

Disposal

Dispose of the product according to local regulations. If in doubt, consult your local authorities.

Feedback and Help

We would love to hear your feedback. To ensure we are providing the best customer experience possibl, please consider writing a customer review.
Scan QR Code below with your phone camera or QR reader:

https://www.amazon.com/review/review-your-purchases/listing/?ref=HPB_UM_CR

If you need help with your Amazon Basics product, please use the website or number below.
amazon.com/gp/help/customer/contact-us
+1 877- 485- 0385

amazon.com/AmazonBasics
MADE IN PHILIPPINES
V02-02/24

Documents / Resources

| amazon basics B07J4HXZ6Q Door Lever [pdf] User Guide
B07J4HXZ6Q Door Lever, B07J4HXZ6Q, Door Lever, Lever
---|---

References

• Amazon Basics

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>