beko WTLJI17C1DM Fully Automatic Washing Machine Instruction Manual

beko WTLJI17C1DM Fully Automatic Washing Machine

Operation Manual

It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure the book is supplied with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant warnings. These warnings have been provided in the interest of safety. You must read them carefully before installing or using the appliance.

Specification

Parts name

Accessories

Symbol definition

Cautions

Installation and adjustment

Please install and adjust the machine according to the requirements of the manual. Correct operation is very important for your safety.

Unpacking

• Unpack the carton and take out the bottom cover.
  Open the top lid of washing machine and take out all of the accessories.

• Remove all wrappers, including the polystyrene base.

• You are advised to keep all the packaging for reuse in case the machine is to be transported again.

Installing the bottom cover

• Let the back of the washing machine incline forward, make the side of the bottom cover with sticker description back to the washing machine, and insert to the bottom of washing machine along the direction of the arrow.
• Remove two fixing clamp by scissors, insert to the accordingly holes black lines indicating ( gently pull the fixing clamp should not be pulled out ), and make the bottom cover fixed on the base.

Positioning
The distance between the washing machine and the wall should be more than 50mm, and the maximum allowed angle of the shank base of the machine is 1 .
The slanting or rough ground may cause the operating stop or unstable, please adjust it with the following methods:

• Horizontal checking
  Observe the water bubble in the balancing apparatus is in a red circle or not. In the red circle, it is horizontal.

• Adjust the adjustable foot

  1. Lift up the adjustable foot gently, loose the adjustable nut, and twist the adjustable foot.
  2.  Fasten the nut after adjustment.
  3. Set the machine flat, and observe again. If the water bubble Loosen  is not in red circle, repeat the above procedure, till the water bubble is in red circle.

How to use  drainpipe

Install drainpipe
Set the drainpipe clip into the drainpipe between 2-3cm from the drainpipe end without pothook. Then install the drainpipe into the right drainpipe connector and fix the drainpipe and drainpipe connector with the clip. After that, put up the drainpipe clip on the cabinet.

How to change the direction of the drainpipe

Water drainage

Water inlet installation

Tap selection

Connect the inlet hose connector to the tap

1. Press down the slider and remove the inlet hose connector from the inlet hose, like below illustration 1.
   

2. Loosen the four bolts on the inlet hose connector till the tap can be accessed, then set the inlet hose connector in the tap, see illustration 2. (If the tap caliber is too larger and could not set the inlet hose end, unscrew the four bolts and take out the bushing, tap exit end must be flat, otherwise it will leak, see illustration 3).

3. Fasten the four bolts in the inlet hose connector evenly, see illustration 4.

4. Twist the fastening nut as in the illustration, see illustration 5.

Remark before twisting the nut, the threading is about 4mm above the upper surface of the nut, after twisting,
the threading is less than 2mm above the upper surface ofthe nut, see illustration 6.

Connect the inlet hose to the washing machine

1. Do not take off the water absorption cushion. Please check if the cushion is dropped or damaged before each usage. If it is contact the seller immediately.
2. Put the inlet hose nut on the inlet valve connector
3. Fasten th inlet hose nut and swing it gently to make sure if it is suitable. 

Cautions: When install the washing machine, please use a new hose. Do not reuse old hose

Connect the inlet hose connector to the inlet hose

1. Put the slider down and insert the inlet hose into the inlet hose connector.
2. Insert the hose firmly and the click sound is heard.

Check the connection between the inlet hose connector and the tap

1. Swing the inlet hose gently to confirm if it is fastened.
2. After installation, open the tap and check if it leaks.
3. Do not bend the inlet hose.
4. Before each usage, check the connection between the inlet hose connector and the tap, and the installation of the inlet hose. Make sure they are firmly fitted to prevent dropping from improper installation position.

Dismantle the inlet hose

1. Close the tap.
2. If you use the washing machine more than once a week, there is no need to remove the inlet hose connector to avoid damaging the fixing screw.

Preparation before operation

Preparation before washing

1. Connect the inlet hose and open the tap.
2. This appliance must be earthed. Confirm the socket is earthed reliably and insert the power plug. The earth terminal should not link to gas pipelines, tap pipelines etc.
3. Put down the drainpipe.

Warning: the temperature of the water should be less than 50

Before washing the laundry, please pay attention to the following

Load laundries

• The capacity of washing and spinning of the machine refers to the largest weight of the standard laundries under dry conditions. The washing quantity shall be lower than the rated capacity. The maximum capacity of this machine is 17 .0kg.
• Different thicknesses, size, and type of laundries will influence the actual washing capacity.
• Do not select high water levels when laundries are less than 1.5kg to avoid water splashing.

Use of detergent

pis put the needed washing power in the detergent box and softener in the softener box evenly

How to use softener

• The machine automatically adds the softener to the inner tub during the last “rinse” process.

How to use bleach

• Fill the water to the selected level, dilute the bleach in the container, and pour it slowly into the washing tub.
• Do not use bleach for colored or figured laundries as they are prone to lose colors.
• Do not put bleach to laundries directly.
• Refer to the manual for the usage and quantity of the bleach.
• Please dissolve powder bleach before use.

How to use the washing powder

• Dissolve in the machine directly (not suitable for the preset program)
  1. Low water level.
  2.  Add the washing powder, and run for 30 seconds to dissolve it completely.
  3. Put laundries in and select suitable water level.
• The instant dissolving of the washing powder
  1.  Prepare warm water of 30°C in a container.
  2. Pour the powder while stirring to fully dissolve it.
• Washing powder with poor quality or not used for a long period may get blocked, please clean the detergent box in time.

Remarks: avoid splashing of water and waste of washing powder, water level should not be too high if laundries are too small.

Control panel instructions

Control Panel
Mode and meaning of the indicator light

•  At the beginning of start, pressing”WATER LEVEL”, at the same time press “PRESET /AIR DRY/SPEED”, you can select WATER RECYCLE, INVERTER WASH, INVERTER SPIN. Only both RINSE and SPIN are selected, WATER RECYCLE can be selected. When you choose INVERTER WASH, INVERTER SPIN, and press
  ” PRESET/AIR DRY/SPEED” to choose a different washing speed and dehydration.

• During working, press “WATER LEVEL” and “PRESET/AIR DRY/SPEED” to set CHILD LOCK, press again to unlock this function.

• Before washing, the Digital Timer shows the set time, unit is Hour.

•  When washing, the Digital Timer shows the remaining time of washing,

• When trouble is encountered, the Digital Timer shows trouble code.

• When it is ON and if with Fuzzy logic.the Digital Timer shows”

• To switch on the Washing Machine to working state or waiting state.

• After selecting the PROGRAM, PROCESS and WATER LEVEL, press this button to start. Press this button to pause during working, press again to continue.

• Select one program form NORMAL, SOFT, FAST, WOOL, CHILD, FOAM CLEAN,
  TUB CLEAN, AIR DRY, STANDARD and Heavy.

• If choose the “NORMAL” program, the wash time is “15 minutes”, spin times is “2”, spin time is “5 minutes”, you can cancel one of the process (but if you choose “SOAK”, the wash time can not be cancelled).

• If choose “FAST” program, the wash time is “9 minutes”, spin times is “1”, spin time is “3 minutes”, you can cancel one of the process (but if you choose “SOAK”, the wash time can not be cancelled)

• If no selection is selected, the process will start with the NORMAL program when the “START/PAUSE” button is pressed.

• At the beginning of start, press this button to select preset time from 2-24 hours.

• If want to cancel preset time, press “POWER” to make the washing machine in waiting state.

• If need to select air dry, please press “PROGRAM” button to select airy dry, then press this button to set air dry time.

• At the beginning of start, pressing “WATER LEVEL” button and press ” PRESET/AIR

• DRY/SPEED” button and choose inverter wash or inverter spin, and press it again, then you can choose washing speed or dehydration rate.This function is only applicable to “STANDARD ” and “HEAVY” program. digital tube display the corresponding rotational speed as follows:

• At the beginning of start, if with FUZZY logic and do not select water level, the digital timer shows”- -“. At this time, before press START/PAUSE, If select STANDARD or HEAVY, with fuzzy logic. When select NORMAL, no fuzzy logic, the water level
  is “10”; When select FAST, no fuzzy logic, water level is “2”. If no WASH process, no fuzzy logic.

• At the beginning of start, press WATER LEVEL to select water level, at this time, no fuzzy logic function, you can select appropriate water level. According to your laundries quantity.1-2 is low water level, 3-6 is middle water level,7-10 is high water level.

• During wash (including rinse), if need to add water, press WATER LEVEL button to add water, un-press will stop adding. Or PAUSE the washing machine and press WATER LEVEL to select higher water level, then press START/PAUSE button, The washing machine Will add the water to setting level automatically and continue working. If your resetting water level is lower than present water level, the lower water Level will valid in next water inlet.

• Automatically add water: during SOAK, WASH and RINSE process, if the washing machine check the water level is lower than setting water level, The washing machine will pause and add water to setting water level automatically.

• Use DIY program, you can set spin time.

• At the beginning of start, the spin time setting is “7 minutes”.

• At the beginning of start, you can press “SPIN” to set spin process only, press “SPIN” again to set spin time.

• Use DIY program, you can set rinse times.

• At the beginning of start, the rinse times setting is “2 times”.

• With DIY program, you can choose soak function and wash time.

• Pressing “WASH” button for 2 seconds to choose soak function, pressing for 2 seconds again to cancel soak function.

• Under “STANDARD”, ” HEAVY” programs to choose soak function, the soak is before wash.

• At the beginning of start, the wash time is “15 minutes”.

Put through the power, press POWER button, the machine is in default “NORMAL” program.

And when the program is setted as “STANDARD” or “HEAVY”, there will be FUZ2Y function:

1. lf there is no water in inner tub, washing machine is in ” FUZZY” condition, washing time is “15 minutes”, rinse time is “2 times”, spin time is “7 minutes”, water level and preset are displayed “–“, program is “STANDARD” If press “START/APAUSE” button (or press “PROGRAM” to select “HEAVY” ), the washing machine will start to sense and automatically
   sense the weight of laundries and set water level.

2. .lf there is water in inner tub, the washing machine is not in “FUZZY” condition, washing time is”15minutes”, rinse time is “2 times”, spin time is “7 minutes”, water level is “7”, program is “STANDARD”, digital time displays the time to finish washing.

Operation steps

1. Put through the power, press POWER button, the machine is in default “NORMAL” program. And when the program is setted as “STANDARD” or “HEAVY”, there will be FUZZY function:

   • If there is no water in the tub, the machine is in the condition of FUZZY, indicator light of WASH is 15, RINSE is 2, SPIN is 7; water level is under setting, preset displays”–“, program is STANDARD. If press START/PAUSE(press “PROGRAM” and select “HEAVY “, the washing machine is in state of “FUZZY”), the machine will detect the laundry quantity and set the water level automatically.
   • If there is water in the tub, the machine is in the condition of NON FUZZY, indicator light of WASH is 15, RINSE is 2, SPIN is 7; indicator light of water level is 7, program is STANDARD, LED displays the program time. You can press WASH, RINSE, SPIN, for process to set different wash time ,rinse times, spin times and soak time.

2. At the beginning of start, you can press “SPIN” to set spin process only, press “SPIN” again to set spin time.

3. Select appropriate water level according to your laundries quantity.

4. At the beginning of start, if need to select INVERTER WASH,INVERTER SPIN and WATER RECYCLE, pressing “WATER LEVEL” button and press ” PRESET/AIR DRY/SPEED” button, each time press” PRESET/AIR DRY/SPEED” button, circularly select INVERTER WASH, INVERTER SPIN and WATER RECYCLE. Only you select RINSE and SPIN, you can select WATER RECYCLE. When you choose INVERTER WASH, INVERTER SPIN, and press
   ” PRESET/AIR DRY/SPEED” to choose a different washing speed and dehydration.(Find details in the chapter of “the situatin and meanig of the indicator lamp), This function is only applicable to “STANDARD” and “HEAVY” program.

5. At the beginning of start, if need to select preset, please press ” PRESET/AIR DRY/SPEED” button and select appropriate preset time, the preset time is shown in the digital timer, and the time indicates the time to finish the whole washing. If want to cancel preset, please press
   “POWER” to make the washing machine in waiting state.

6. At the beginning of start, if need to select air dry, press ” PROGRAM” button and select AIR DRY program, press “PRESET/AIR DRY/SPEED” can select the time of AIR DRY. When the air dry function is over, the washing machine will be in waiting state.

7. Close the top lid, press “START/PAUSE” , the washing machine is working. During working, press “WATER LEVEL” and ” PRESET/AIR DRY/SPEED” button, child lock function will start, press again, unlock this function. If open the top lid, washing machine stop working and give an arm.

8. When the washing is finished, buzzer alarm, power supply cut off automatically.

Maintenance

Maintenance methods

1. After using the machine, you are advised to turn off the water taps. (if necessary, pull out the inlet hose).
2. Do not keep water in tub for a long time. When washing is finished, drain it right away.
3. Once you have finished using the machine, you are advised to unplug it.
4. Put the electric cable and the drain hose in order.
5.  Wipe the water on the surface and in the tub with soft cloth and keep the top lid opening for a while. It helps to prevent mold and smell forming inside the appliance.

If the water in the inner tub has possibility to freeze, please do like below:

1. In winter, if remaining water freeze can cause the washing machine trouble, please take off the water inlet hose and drain out the water in the hose and inner tub.°
2. If the water freeze, please don’t operate the washing machine. Put 40 C hot water in the tub, the hot water should submerge the pulsator, after a few minutes, rotate the pulsator by hand gently, then you can operate the washing machine.

Troubleshooting

Before contacting the technicians, please make the following checks:

Notes : If there is still a fault after the above checks, please pull out the plug and contact the seller right away. It is dangerous to repair this product by yourself.

Other functions

1. Abnormal display

2. lmbalance adjustment
   During spinning, if the laundries are not placed equally in the tub, it would cause Violent vibration. This machine has imbalance adjustment function, and the vibration testing system will supervise the running. Once vibration is beyond certain level, the adjustment system will start automatically to adjust the imbalance.

3. Power supply is cut off automatically

4. If you did not start the program in 10 minutes after pressing the power supply button, the power supply will be cut off automatically.

5. After the washing is finished, alarm buzzes and the power supply will cut off automatically.

6. Child lock function

7. When child lock function is set, all the buttons will be locked including POWER. If the top lid is
   opened during the washing machine working, the washing will be stopped and give an alarm. But
   if you can close the top lid in 5 seconds, the alarm will stop and the washing machine will continue working. If cannot close the top lid in 5 seconds, the washing machine will begin draining if there is
   water in the inner tub, even closing the top lid is not valid. During the draining, alarm will buzz every
   1 O seconds, when the water in the inner tub is about 5cm higher, alarm will buzz every 1 O minutes. When the draining is finished, the washing machine will be in the state of waiting, if close the top lid, the washing machine is unlocked and start working as previous setting.

8. Once child lock is set, if top lid is opened over 5 seconds during washing or rinse(there is water in the inner tub), washing machine will drain and alarm will buzz. If you unlock the function during draining, the washing machine will add water to water level set and continue working.

9. Water recycle function
   When water recycle function is set, after the last rinse finished, the washing machine will not drain and spin.SPIN and WATER RECYCLE indicator light will be flashing and alarm will be given,the washing machine will stop working (if nobody operate, the alarm will be given every 10 minutes, in 1 hour, power supply will be cut off automatically). When press START/PAUSE, WATER RECYCLE indicator light is on and the washing machine begin to drain and spin, the user can reuse the water.

10. lnverter washing function Direct Drive motor is used on this machine. At the beginning of start, If you want to choose a different washing speed and dehydration rate on the initial state, pressing”WATER LEVEL” button and press ” PRESET/AIR DRY/SPEED” button, choose inverter wash and inverter spin (This function is only applicable to “STANDARD” and “HEAVY” program). And then press ” PRESET/AIR DRY/SPEED” button, choose different washing speed and dehydration rate to suit different clothes and achieve better  washing and spining

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>