MuxLab 500842 HDMI-3G-SDI Single Display User Manual

HDMI/3G-SDI Single Display 17.3″, 4K/30
User Manual
500842 © MuxLab Inc. 2024
94-001014-A/SE-001014-A

Safety Precautions

To ensure the best performance from the product, please read all instructions carefully before using the device. Save this manual for future reference.

• Follow basic safety precautions to reduce the risk of fire, electrical shock, and injury.
• Do not dismantle the housing or modify the module. It may result in electrical shock or burns.
• Do not open or remove the housing of the device as you may be exposed to dangerous voltage or other hazards.
• To prevent fire or shock hazard, do not expose the unit to rain, moisture and do not install this product near water. Keep the product away from liquids.
• Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on the housing, unplug the module immediately.
• Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
• Using supplies or parts not meeting the product specifications may cause damage, deterioration or malfunction.
• There are No adjustable components in the monitor. Refer all servicing to qualified service personnel.
• Install the device in a place with adequate ventilation to avoid damage caused by overheat.
• Unplug the power when left unused for a long period of time.
• Information on disposal of devices: do not burn or mix with general household waste, please treat them as normal electrical waste.

Copyright Notice
All contents in this manual are copyrighted, and cannot be cloned, copied, or translated without the express permission of MuxLab Inc. Product specifications and information in this document are for reference only, and the content may be updated from time to time without prior notice.

Introduction

The HDMI/3G-SDI Single Display 17.3″, 4K/30 features a 17.3-inch IPS LCD display that can be conveniently and securely rack-mounted into a 19″ 7RU rack. This monitor adopts digital signal processing circuit which enables it to achieve high brightness, low power consumption and stable performance.

The unit supports input and loop-out of HDMI signals up to 4K/30, SDI signals up to 3G-SDI, DVI-I (VGA) and CVBS signals with Audio. The unit supports a tri-color Tally light indicator per display, customizable buttons allowing customers to tailor them to their needs, and advanced functions such as Center Marker, Safe Frames, Check Field, Focus Assist, Aspect Ratio, Image Flip, P2P, and Image Freeze.

Features

• 17.3-inch LCD display
• Supports HDMI (4K/30), 3G-SDI, DVI-I (VGA) and CVBS with Audio
• Fits 19-inch rackmount @ 7 RU
• Tri-color Tally light indicator
• Supports Center Marker, Safe Frames, Check Field, Focus Assist,
• Aspect Ratio, Image Flip, P2P & Image Freeze
• Stereo Earphone output, built-in speaker
• Customizable buttons tailored to customer needs

Package Contents

• One (1) HDMI/3G-SDI Single Display 17.3″, 4K/30
• One (1) 12VDC power adapter 36W
• One (1) Tally – DB9 adapter
• One (1) USB cable adapter
• One (1) User manual (available via download)

Specifications

Specification

Screen Size| 17.3″ IPS
Display Colors| 16.7M
Dot Pitch| 0.1989(H) x 0.1989(V) mm
Aspect Ratio| 16:9
Brightness| 300cd/m²
Contrast| 700:1
Backlight| LED
Response Time| Tr + Tf = 25ms
Viewing Angle| 89°/89°(L/R)  89°/89°(U/D)
Inputs| 3G-SDI, HDMI, YPbPr, Video, Audio(L/R), DVI-I (VGA), Tally, USB Upgrade
Outputs| 3G-SDI, HDMI, YPbPr, Video
Audio| 3.5mm Stereo Headphone, Speaker
SDI Support Format| 480i/576i
720p (60/59.94/50/30/29/25/24/23.98)
1080i (60/59.94/50)
1080p (60/59.94/50/30/29.97/25/24/24sF/23.98/23.98sF)
HDMI Support Format| 480i/576i/480p/576p
720p (60/59.94/50/30/29/25/24/23.98)
1080i (60/59.94/50)
1080p (60/59.94/50/30/29.97/25/24/24sF/23.98/23.98sF)
4K UHD 3840x2160p (30/29.97/25/24/23.98Hz, 4096×2160 (24Hz)
Power Consumption| ≤26W
Input Voltage Range| 9.0 to 24 VDC
Power Source| 100/240VAC to 12VDC @ 3A power supply
Working Temperature| 0°C to 50°C
Storage Temperature| -20°C to 60°C
Dimensions| 481.6L X 297H X 35D mm
Weight| 3.40kg
Warranty| 2 years
Order Information| 500842  HDMI/3G-SDI Single Display 17.3″, 4K/30 (UPC: 627699008423)

Operation Controls and Functions

6.1 Front Panel

operate on user presets.
4| Input Selection Buttons| Video input selection: VGA (DVI to VGA signal), DVI, VIDEO, YPbPr, HDMI and SDI
5| Audio output| 3.5mm Stereo Headphone Jack output
6| Tally| Tally Indicator

Multifunctional Knobs

Knobs| Function when OSD is not displayed| Function when OSD is displayed
---|---|---
| Rotate knob to adjust image Saturation.
Press it to enter the OSD menu.| Rotate knob to select or adjust the selected menu item.
Press it to exit (confirm) the current menu settings.
| Rotate knob to adjust image Brightness.| Rotate knob to select menu items up or down.
Press it to exit the OSD menu.
| Rotate knob to adjust image Contrast.
Press it to enter “Focus Assist” function.| /
| Rotate knob to adjust Volume.
Press it to enter “Camera Mode” Function.| /

6.2 Rear Panel

Rear Panel

signal conversion)
9| TALLY| TALLY indicator input port
10| USB UPGRADE| USB upgrade port
11| Power input| Direct DC plug-in power supply input port
12| Power input| 4-pin XLR DC power input

6.3 Power Input Selection
There are two ways of power supply to our monitor:

A. The direct plug-in DC power input port. Please use DC5.5*2.1m DC power plug, power input polarity as shown: Please use the qualified power supply with output power no less than 21W 9-24VDC.
B. Via 4 pin XLR interface power supply. The polarity of the 4-pin XLR power input is shown below.

6.4 TALLY Indicator Pinout

Note: Pin 5 and 8 are sharing GND connection.

On Screen Display Menu (OSD) Instructions

The display has a number of buttons for controlling and adjusting setting for display.

• Pressing the MENU knob will enter the On Screen Display (OSD), turning the knob to select secondary menu.
• Turning the Esc knub to navigate the secondary menu.
• After selecting the item, rotate the Menu knob to ajust the item parameter.
• Pressing the ESC knob will exit the OSD menu.

7.1 On Screen Display Menu (OSD) Functions

| ● Pic. Mode: Standard, Mild, User, Dynamic, Under “User- “, you can adjust the Brightness (0 ~ 100), Contrast (0 ~ 100), Saturation (0 ~ 100), and Sharpness (0 ~ 100).
● Color Temp. : 6500, 9300, User; Under “User”, you can adjust the Red, Green and Blue values of the image.
● Tint: 0〜100
---|---
| ● Language: Language selection.
● Aspect   Ratio: Auto, 4:3, 16:9, Just Scan, Panorama, P2P.
● No Signal: Screen color when no video signal; Blue Screen, Red Screen, Green Screen, Black Screen, White Screen
● VGA Self-adj: This function can be realized under DVI to VGA signal.
● OSD Trans. : Off, Low, Middle, High
● OSD H: 0〜100
● OSD V: 0〜100
● OSD Time: Off, 10Sec, 20Sec, 30Sec
● Camera Mode: Off, 480P, 1080i
● Backlight: 0〜100
● USB Upgrade: Download upgrades to a USB disk, then connect it to the Upgrade USB port, then press confirm. After the upgrade, the monitor will automatically restart. Do NOT plug any USB cable into this port.
● Reset: reset to the original settings.
| ● Zoom: Off, 4X, 9X, 16X.
● Zoom Mode: Off, Mode1, Mode2; In Mode 1 and Mode 2, you can customize the Zoom All (0-100).
● Scan Mode: Under Scan, Over Scan
| ● Center Marker: Off, On
● Safe Frames: Off, 80%, 85%, 90%, 93%, 96%, 2.35:1
● Image Freeze: Off, On
● Image Flip: Off, H Flip, V Flip, H_V Flip
● OSD   Flip: Off, On
● Check Field: Off, Mono, Red, Green, Blue,
● Focus Assist: Off, On; Superimpose red highlight over parts of the monochrome image in focus.
| ● F1 to F4: Center Marker, Safe Frames, Check Field, Focus Assist, Aspect Ratio, Image Flip, P2P, Image Freeze, Zoom, Backlight, Color Temp., VGA Self-adj can be pre-selected for each Function button.
Choose F, rotate button, then rotate button to select one of options as definition function. Press “MENU” button to confirm and rotate button back to next F setting.

Troubleshooting

If there is any problem when using the unit, please try following ways to inspect and solve

cable and make sure to select the correct input interface
Without video signal input| Check that the signal source and output interface connection are correct.
Monitor cannot be powered on| Check whether the power is connected, put the power switch to “on” position
Supply voltage instability| The power adapter is not connected properly.
Image/color display abnormal| Video cable poor contact| Change video cable
Video signal interfered by external environment| Move to another environment and try again
Video input signal amplitude too low| Check signal source video output, or change signal source and try again.
Menu color saturation adjustment closin| Enter menu to check color, or reset to factory settings
Reset Check Field, back to the color
Check Fieldset in mono or black Et white
Image deformation| Reset the image ratio
Speaker without sound| Audio cable off or improper connection| Confirm connected with the corresponding input port
Volume adjustment was closed| Reset the volume control and adjust to a proper position
HDMI cable poor Connected| Check the quality of cable, or change cable and try again
No sound after switch video signal| This monitor is with audio signal only in audio input and HDMI state

If you still cannot diagnose the problem, please call MuxLab Customer Technical Support at 877689-5228 (toll-free in North America) or (+1) 514-905-0588 (International).

Application Diagram

HDMI/3G-SDI Single Display 17.3″, 4K/30
500842
Follow us: 2321 Cohen | St-Laurent , H4R 2N7 | Québec, Canada Tel: 514-905-0588
Fax: 514-905-0589 | Toll free: 1-877-689-5228 info@muxlab.com
salesteam@muxlab.com | www.muxlab.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>