Snow Peak GT-120 GigaPower Folding Torch User Manual
- June 4, 2024
- Snow Peak
Table of Contents
GT-120 GigaPower Folding Torch
User Manual
Outdoor Use Only
Instruction Manual: Ver 1.01
GT-120
GigaPower Folding Torch
This product is a torch developed for use outside. Do not use it indoors, in a
car, or in a tent. There is a risk of death from carbon monoxide poisoning or
suffocation due to lack of oxygen. Please be careful to ensure proper
ventilation, especially in small spaces outdoors. Use caution to avoid burns,
as the main body becomes hot during and immediately after use. Please keep
this product out of the reach of children.
Thank you for purchasing this Snow Peak product. For safe use, please read the
following instruction manual carefully. Keep it in a safe place after reading.
If you do not understand the instructions or if you find a problem with the
product, stop using it immediately and contact the store where it was
purchased or Snow Peak customer service. All Snow Peak combustion equipment is
shipped after undergoing a combustion test.
Warnings and cautions in this instruction manual
WARNING This symbol indicates that if mishandled, the user bears the risk
of dying or being seriously injured.
CAUTION This symbol indicates that if mishandled, the user risks injury
and likely damage of surroundings.
Set Contents (name of each part)
Specs
Material| Body/ Stainless steel, aluminum, brass Handle/ Natural wood, Storage
Case/ Nylon
---|---
Size| 277 (10.9″) x 73 (2.8″) x 205 (8″) (h) mm
Storage Size| 191 (7.5″) x 70 (2.7″) x 43 (1.7″) mm
Weight| 250g (0.551bs)
Gas Usage| 300g/h (10.6oz/h)
Output| 3,500kcal/h
Compatible Fuel Canister| GP-110S/GP-2505/GP-5005 GP-110SR/GP-250SR/GP-5005F1
How to attach a canister
WARNING
- Do not use anything other than the designated canisters listed above. Please note that if you use a canister that is not specified, you will not be covered by product warranty and repair.
- Before attaching the canister, be sure to check the mounting screw (connection point) of the instrument plug and the O-ring for any abnormalities. Do not attach the canister if any abnormality is found.
CAUTION
- Install with the canister upright (valve up).
- A small amount of gas may leak when installing or removing the canister. Do not attach or detach the canister near fire or in a space with poor ventilation.
-
Make sure that the main body has cooled, then push the handle lock pin with the tip of your fingernail to open the handle in the direction of the arrow as shown in the figure. When you open the handle completely, you will hear a click and it will lock into place.
-
Turn the instrument stopper knob clockwise until it stops, to ensure the flow is completely shut off.
-
Ensure the canister is level, align the threaded part of the canister with the threaded part of the main body, and smoothly screw clockwise, as shown in the figure. Ensure the bottom of the handle touches the edge of the canister. Ensure there is no odor or gas leaking from the connection.
How to operate
After installing the canister, ensure there is no continuous noise or
offensive odor from the main unit plug and connection point. Check to make
sure gas is not leaking. If gas is leaking, stop using it immediately and
contact the store where you purchased the product or Snow Peak customer
service for repair.
WARNING
- When igniting, do not bring any part of your body close to the burner or look into the burner. There is a risk of sudden large flames and burns.
- Place it in a stable place and ignite it. When igniting, make sure there is nothing flammable around you.
-
How to ignite.
Turn on the match or lighter in advance and keep it close to the burner’s mouth. Turn the instrument stopper knob slightly counterclockwise to ignite. If you cannot ignite the first time, close the instrument stopper knob and repeat the same process.
-
How to adjust the power. When the instrument stopper knob is turned counterclockwise, the flame becomes stronger, and when it is turned clockwise, the flame becomes weaker. Turn the instrument stopper knob slowly. After ignition, it can be used upside down once the flame stabilizes. Please adjust the flame according to the environment during use.
-
Be sure to hold the handle while the torch is on fire.
- How to extinguish.
Turn the instrument stopper knob clockwise completely. Make sure the torch is completely silent and the fire at the end of the nozzle is visibly extinguished.
*Depending on the usage conditions, combustion may continue for a while even after closing the instrument stopper knob.
- How to extinguish.
How to take out fuel canisters.
Be sure the main body is completely cool as the body will be hot after use.
Level the container and turn the fuel canister in the opposite direction to
when it was first attached. Hold the instrument and fuel canister to remove
from each other.
How to store
-
Make sure that the main body has sufficiently cooled, and then close the handle in the direction of the arrow as shown in the figure, while pushing in the handle lock pin
with the tip of your fingernail. Once you close the handle completely, you will hear a click and the lock will be secured.
-
Rotate the instrument stopper knob to fold it in the direction of the burner, then put it in the storage case. Use caution as the knob may suddenly flick out if nudged or bumped.
Precautions during use
Do not use if there is a gas leak or other malfunctions, or if the product has been dropped or damaged. If one of these occur, contact the store where you purchased the product or Snow Peak customer service for repair.
- Do not use it for any purpose other than starting a fire.
- Before using, make sure that there is no dust or dirt on the instrument plug. Always clean the instrument plug and do not let it touch the ground carelessly. Adhesion of dust or dirt may reduce the output, prevent gas from being emitted, or cause a malfunction such as gas leakage.
- Do not leave it ignited. Hold firmly to the handle of the torch and do not release it during use.
- Do not use it for cooking.
- Occasionally check to ensure the combustion condition is normal during use.
- Note that the gas pressure and flame size will change depending on the air temperature, the temperature of the container, and the combustion state.
- Do not leave or store the container in a place where the temperature exceeds 40 C/104 F, such as in direct sunlight, next to a heat source or near a fire. The increase in the temperature of the canister may result in the canister exploding.
- Keep out of the reach of children.
- Note that flame may be extinguished while in use if there are strong winds.
- If abnormal combustion occurs, immediately extinguish the fire, discontinue use, and contact the store where you purchased the product or our customer service for repair.
- The metal that is exposed to the flame will burn and discolor, but this will not affect the performance of the torch.
- Do not use anything other than the accessories or specified items of this product.
- If you smell gas before use, do not ignite, and remove the canister immediately. Extinguish the fire and flames of all other burning stoves in use.
- The main body is hot during and immediately after use. Do not touch anything other than the handle and instrument stopper knob to avoid burns.
- Do not use if there are flammable materials nearby.
- Do not leave the product wet. It may cause rust.
- After use, remove dust and dirt from the main unit. Keep the combustion part clean at all times. If there is dust in the combustion part, the torch will not be able to reach peak performance and abnormal combustion may occur.
How to maintain
Be sure to perform inspections and maintenance before and after use.
- Before use, always check the screws and O-rings at the joint between the main body and the canister for any abnormalities. If the product is damaged or worn, contact the store where you purchased the product or Snow Peak customer service for repair.
- Turn the instrument stopper knob clockwise (as viewed from the front) to ensure the gas is completely shut off.
- Before putting it in the storage case after use, ensure the main body is sufficiently cooled before putting it in.
- Do not use this product if you think it is broken or damaged.
- Be sure to ask the store where you purchased the product or Snow Peak customer service for repair. It is dangerous to attempt repairs by yourself.
How to identify and deal with failures/abnormalities
The temperature of the canister is high| | | | | | | | Exchange for a normal-
temperature canister
---|---|---|---|---|---|---|---|---
Nozzle clogging| | | | | | | | Request inspection and
repair
Burner section clogging| | | | | | | | Clean carefully
with a cloth to avoid damage
Canister abnormality| | | | | | | | Replace with a
new canister
Defective spindle| | | | | | | | Request inspection and repair
Insufficient installation of canister| | | | | | | | Confirm the
canister is attached
Instrument plug failure| | | | | | | | Request inspection and
repair
Defective handle| | | | | | | | Request inspection and repair
Abnormality of
canister screw| | | | | | | | Replace with a new canister
The dedicated canister is not in use| ****| | | | | | | Use a compatible
canister
Cause Effect| The canister cannot be attached| Gas leaks| Doesnot ignite|
Weakfirepower| Uneven flames| Flame disappears during use| Does not
extinguish| Treatment method
● If you still have problems with the product or need additional clarity after
checking each of the solutions above, please contact the store where you
purchased the product or Snow Peak customer service.
Quality assurance
We have taken all precautionary measures to ensure this product is good
condition. If you find defects or inadequacies, please contact Snow Peak
customer service. If the defect is caused by a manufacturing defect, we will
repair or replace the product free of charge. In other cases of defects, we
will repair at the appropriate price. The decision of repair or replacement is
at Snow Peak’s discretion. Please note that the following cases are not
covered under warranty.
- If the user did not follow the instruction manual.
- The natural end of product life is due to aging and deterioration of materials.
- Failure due to modifications or rough handling.
- Product failure due to an unexpected accident.
- Product failure due to other manufacturer’s defects.
- Failure due to dust or rust.
- Damage caused by disassembly.
- Damage from dropping or other impacts or jolts.
- Failure due to wear and tear on the product.
- Failure due to using the product in combination with another maker’s products.
WARNING: This product can expose you to chemicals including lead, which
is known to the State of California to cause cancer and birth defects or other
Reproductive Harm.
For more information go to
www.P65Warnings.ca.gov.
The Manual for Snow Peak gas appliances and special canisters Contains
important notes. Please read well and keep this manual in a safe place.
Before use
Please read carefully to ensure safety and avoid accidents.
Never use this product in a tent, car, or indoors. This product is designed
for the outdoors and consumes a large amount of oxygen during use. Never use
it in a tent, car, or indoors. Oxygen deficiency and toxic gas can cause death
or serious carbon monoxide poisoning. It can also cause a fire.
DANGER
This symbol indicates an action that could result in a serious life-
threatening accident.
● Please use the designated canisters for this product.
The Snow Peak canisters are designed to maximize the performance of this
product. Do not use any other canister. Please note the recommended Snow Peak
fuel canisters below.
Snow Peak fuel canisters
-
GP-110S
-
GP-250S
-
GP-500S
-
GP-110SR
-
GP-250SR
-
GP-500SR
-
If you use a canister not specified above, you will not be covered by the product warranty and repair. Canisters other than those above have different specifications such as valve shape and nozzle thickness. Because of the differences in basic design, gas leaks may occur, causing ignition, fire or abnormal combustion.
Canisters from other manufacturers
-
Never repair or modify this product by yourself. This product and canister are made with professional precision. Modifications not only reduce performance but can also cause incomplete combustion and gas leaks. For repairs, contact the store where the product was purchased or Snow Peak customer service.
-
Always check that no gas is leaking before igniting.
Ensure the stopper knob is closed before attaching the canister. After installing the canister, ensure there is no gas leaking at the connection before igniting. Igniting when there is a gas leak may cause burns due to abnormal combustion or poisoning. If you notice any abnormality, stop using the product immediately and contact the store where you purchased the product or Snow Peak customer service. -
Do not intentionally inhale the gas in the canister. If you inhale gas intentionally, you will suffocate due to a lack of oxygen.
-
Never refill the canister. The special canister is not designed to be refilled after its initial factory fill.
-
Store the canister in a place below 40 C/104 F. The internal pressure of the canister rises as the outside air temperature increases. Do not store in places where the temperature exceeds 40 C/104 F, such as in a car or in direct sunlight.
WARNING
This symbol indicates that if mishandled, the user bears the risk of dying or
being seriously injured.
-
Do not use, leave, or store this product with the canister attached, on surfaces that are 40 C/104 F. or warmer.
Sandy beaches, stony riverbeds, or paved roads exposed to direct sunlight are hotter than the outside temperature. If the canister is left on or this product is used, the canister may overheat and the internal pressure may rise sharply, causing abnormal combustion or explosion. -
Be sure to hold the handle while using this product.
Be sure to hold the handle to ensure a safe grip of the product. In addition, if the canister is left sitting in place, the internal pressure of the container may rise sharply due to the radiant heat of the fire or a change in the direction of the wind, causing abnormal combustion or explosion. Also, even if you hold it by the handle, immediately extinguish the fire and stop using it if abnormal combustion occurs. -
Do not point the torch at anyone.
-
Do not leave near other heat sources such as heaters and bonfires.
The heat from external sources causes abnormal heating and a rapid increase in the internal pressure of the canister, potentially resulting in an explosion. -
Before connecting the canister, be sure to turn the instrument stopper knob clockwise when looking at it from the front and check that the instrument plug is closed.
The instrument plug may open during storage or transportation. Make sure the instrument stopper is tightly closed when connecting the canister. -
After use, face the instrument stopper knob and turn it clockwise until closed. Always remove the canister before storing it.
If the instrument stopper knob is not closed, gas may flow out little by little and there is a risk of ignition. Also, if the canister is left attached to the main body for long periods, gas may leak. -
When attaching or detaching the canister, keep it upright and do not over-tighten it.
The new canister is completely full of liquid gas. If it is attached at an
angle, liquid gas may spurt out vigorously, which is extremely dangerous. Make
sure that there is no fire in the surrounding area, and install the canister
in an upright position. The connecting screws are a very important part.
Forcibly attaching or detaching the canister, or screwing it in at an angle
may damage the connection and cause a gas leak. -
Check the O-ring (a replaceable piece) at the connection part each time you use it. ****The rubber O-ring wears when the canister is attached or detached. In addition, it deteriorates even if it is not used. Using a damaged or deteriorated O-ring may cause gas leakage. If it is damaged or deteriorated, stop using it immediately and contact the store where you purchased it or our user service.
-
Do not surround this product with windshields, stones, or other barriers.
If you surround this product with a windshield, stones, or other barriers, the canister will absorb heat abnormally. Abnormal temperature increases cause a risk of explosion. -
Keep the product at least 2 meters (6.5’) away from flammable objects at all times.
The heat of the flame flows laterally or downward depending on the wind’s direction. Since it is strongly transmitted upward, keep a sufficient distance between the product and flammable objects to avoid the risk of fire.
-
Do not use this product for any purpose other than starting a fire.
Using this product for anything other than starting a fire, such as heating or drying clothes, may lead to unexpected accidents such as fire, burns, and lack of oxygen. -
Due to the risk of explosion, please dispose of the canister separately from other garbage after it is completely empty. Also, remove the canister when you plan not to use this product for a long time. Put the main body in the storage case, and attach a cap to the canister before storing.
Improper disposal may result in gas leakage causing ignition, fire, or abnormal combustion. If dust or dirt adheres to the main body and the connection screw of the
canister, it may cause it to malfunction.
-
Do not throw an empty canister into a fire or place it near other heat sources.
A small amount of gas will remain even in an empty canister. If you throw it in a fire or place it near another heat source, the internal pressure will rise and it may explode. -
Keep out of the reach of children.
Keep this product and canister out of the reach of children to ensure safety.
-
If the product is dropped or undergoes significant impact, contact the store where you purchased the product or our customer service for inspection even if there is no visible damage.
Internal problems may occur due to deformation or damage from impact.
****CAUTION
This symbol indicates that if the product is mishandled, the user risks injury and may cause damage to the surroundings.
-
Be sure to push the lock pin to secure the handle before opening and closing.
If you try to turn the handle forcibly while it is locked, the handle will be damaged. -
Be sure to inspect the canister before use.
Check the canister before use and before storage. Since gas is enclosed, there is a risk of gas leakage. If there are scratches, dents, rust, etc. on the exterior of the canister, do not use it. -
After use, inspect and clean this product before placing in the storage case.
Moisture or debris may adhere to this product causing the nozzle to clog or rust, potentially resulting in malfunction. Inspect and clean the product so that no problems will occur the next time you use it.
-
Canisters cannot be carried on an aircraft.
By law, gas canisters cannot be carried on an aircraft. -
The main body and each part of the product will become very hot for a considerable amount of time, both during and after use. Please practice caution and be careful to avoid burns.
-
Do not attach or detach the canister near a fire or in a poorly ventilated space.
A small amount of gas may leak when attaching or removing the canister, which may cause flames to ignite, or a lack of oxygen. -
Forcibly attaching or detaching the canister will damage the connection.
For questions or concerns contact the Snow Peak
Customer Service Department.
Snow Peak USA Inc.
+1503-697-3330 (9:00~17:00)
Email: info@snowpeak.com
Snow Peak USA Inc.
404 NW 23rd Ave., Portland Oregon, 97210, USA
Tel. +1 503-697-3330
IG: @snowpeakusa
www.snowpeak.com
Snow Peak, Inc.
456 Nakanohara, Sanjo-shi Niigata 955-0147 Japan
Tel. +81 256-46-5858
IG: @snowpeakusa
www.snowpeak.co.jp
MADE IN KOREA
Documents / Resources
| Snow
Peak GT-120 GigaPower Folding
Torch
[pdf] User Manual
GT-120 GigaPower Folding Torch, GT-120, GigaPower Folding Torch, Folding
Torch, Torch
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>