OLIGHT Obulb Pro Rechargeable S Lantern User Manual

: July 3, 2024
: OLIGHT

Table of Contents

OLIGHT Obulb Pro Rechargeable S Lantern
Charging Instructions
FAQ
IN THE BOX
FEATURES
SPECIFICATIONS
PRODUCT OVERVIEW
UNLOCK THE LIGHT BEFORE FIRST USE
HOW TO USE THE ADHESIVE METAL BADGE
FCC STATEMENT
HOW TO OPERATE
LOCKOUT/UNLOCK
WARRANTY
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

OLIGHT Obulb Pro Rechargeable S Lantern

Charging Instructions

Unlock the light before first use by charging it.
Connect the USB end of the magnetic charging cable to an external USB power source and attach the other end to the charging port at the bottom of the product.
It takes approximately 3 hours to fully charge.
The red indicator means charging, while the green indicates charging completion.
Clean and dry the paste position.
Peel the protective film off the adhesive metal badge without touching the sticky side.
Paste the badge onto the desired position and press evenly to fix it in place.
Attach the Obulb Pro on the adhesive metal badge.

FAQ

Q: What should I do if the indicator lights do not turn on during charging?
A: If the indicator lights do not turn on during charging, please check the connection of the charging cable and ensure it is securely attached to both the power source and the product’s charging port.
Q: Can the product be submerged in water?
A: The product has an IPX7 rating, which means it is protected against immersion in water up to 1 meter for up to 30 minutes. However, prolonged exposure to water should be avoided.
Q: How do I reset the product if it malfunctions?
A: To reset the product, press and hold the button for 10 seconds to perform a hard reset. This should resolve most issues related to product malfunctioning.

Thank you for purchasing this Olight product. Please read this manual carefully before use and keep it for future reference!

IN THE BOX

FEATURES

7 modes are available: Warm white light, red/green/blue light, red flash, fade between 7 colors, cycle between 7 colors.
App control: The Obulb Pro can be controlled by the OLIGHT APP via Bluetooth. With the APP, users can change its mode, brightness, and color, and check the remaining power and runtime. The APP also enables group control and data sharing.
Magnetic bottom: The magnetic bottom attaches to almost any smooth surface when combined with the adhesive metal badge.
Larger Battery: The built-in 1650mAh battery allows up to 84 hours of runtime.
Magnetic charging: With the magnetic charging cable, it can be fully charged in 3 hours.
One-button operation: Single click the rubber-coated button to switch on the Obulb Pro and cycle through 7 light modes, or long press to turn it off.
Suitable size: Measuring 3.7oz and 2.56*2.28in, this light orb is bigger to light a larger area, but still compact enough to be carried by hand or in backpacks.
Sturdy build: IPX7 waterproof and 1.5-meter impact-resistant, the Obulb Pro is ready for any environment and adventure.
Heat dissipation design: The hidden heat dissipation hole prevents distortion caused by overheating.

SPECIFICATIONS

All data above are test results according to ANSI/NEMA FL 1-2009 standards.
The tests are performed using the built-in battery that is fully charged.

PRODUCT OVERVIEW

UNLOCK THE LIGHT BEFORE FIRST USE

NOTE

When the charging cable is connected for the first time, it is normal for the indicator of the cable to flash red once or twice to signal charging cable detection.

CHARGING

Before first use please fully charge the product.
Connect the USB end of the magnetic charging cable (MCC 1A) to an external USB power source, then attach the other end of the cable to the charging port at the bottom of the product. It takes 3 hours to fully charge.
Charged at 4.2V/max 1A.
The red indicator means charging, while the green indicator means charging completed.

WARNING

Input voltage higher than 5V or voltage fluctuation may damage the IC, leading to short-circuit and even melting of the charging interface.

BATTERY TYPE

Built-in 1650mAh 3.7V Rechargeable Lithium Polymer Battery.

HOW TO USE THE ADHESIVE METAL BADGE

Clean and dry the paste position.
Gently and carefully peel out the protective film and DO NOT touch the sticky side.
Paste the sticky side of the adhesive metal badge onto the desired position and press it evenly until it is fixed in place.
Attach the Obulb Pro on the adhesive metal badge.

DANGER

DO NOT drop the light or impact it heavily to protect the built-in battery.
DO NOT charge the product with non-designated power adapters. It may cause battery combustion or even explosion.
DO NOT throw the product into the fire, which may cause battery combustion, explosion or unexpected disasters.

WARNING

DO NOT charge the product if it becomes dirty or wet. Before charging, please clean and dry it.
DO NOT let a pet play with it, in case the pet will bite and damage it.
DO NOT hit it as a ball, which may cause irreversible damage.
DO NOT use it as a baby toy.
DO NOT use it at 60℃ or a higher temperature. Otherwise, it may be damaged or distorted.
DO NOT disassemble or modify the battery, or use the battery for other purposes.

NOTICE

When the light is turned off, the current output mode will be memorized for the next activation.
The output brightness will decrease as the battery runs low and its voltage decreases until the light goes off.
The product can be charged with an MCC3 charging cable, but the charging indicator may not work properly if doing so.
The battery has a thermal protection feature. When the battery is working at a temperature higher than 40℃, the Obulb Pro may not be charged.
When the product has been fully charged with an MCC1A charging cable, the charging will stop.
Once the battery level drops below 95%, the charging will restart.
Only two Obulb Pro should be charged on the Omino at a time.
The Obulb Pro does not support Nightour control.

EXCLUSION CLAUSE
Olight is not liable for damages or injuries sustained resulting from the usage of the product inconsistent with the warnings in the manual, including but not limited to using the product inconsistent with the recommended lockout mode.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

This device may not cause interference, and
This device must accept any interference, including interference that may cause undesired operation of the device.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following.

MEASURES

Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC (IC) RADIATION EXPOSURE STATEMENT
This equipment complies with FCC (IC) radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

HOW TO OPERATE

The button is located at the bottom of the product. It can be operated by pressing the flat part of the bottom, or by pressing the top of the cover if the product sits securely on a hard surface.
ON/OFF: Single press the button to turn on the light. Press and hold the button to turn it off.
The mode and brightness will be memorized.
When the product is turned on for the first time, its default brightness is 10% white light.
While the light is off, press and hold the switch to access the memorized white light.
CHANGE OUTPUT: While the light is on, single press the button to cycle through different modes. The cycle order is as follows: White light→Red→Green→Blue→Fade between colors→Cycle between colors→Flashing red→OFF→White light→…

LOCKOUT/UNLOCK

LOCKOUT
To lock the product, press and hold the button for 2 seconds while the light is off until the white light briefly turns on and off again. In lockout mode, if you press the button for less than 1 second, the low white light will turn on momentarily.
UNLOCK
In lockout mode, press and hold the button for 1 second until the white light flashes once to unlock it. At this time, the memorized white light appears.

WARRANTY

WITHIN 30 DAYS OF PURCHASE: Contact the original seller for repair or replacement.
WITHIN 2 YEARS OF PURCHASE: Contact Olight for repair or replacement.
USB MAGNETIC CHARGING CABLE: One year.

This warranty does not cover normal wear and tear, modifications, misuse, disintegration, negligence, accidents, improper maintenance, or repair by anyone other than an authorized retailer or Olight itself.