EVEREST B0D366KWN9 36 Inch Tall Storage Cabinet User Guide
- July 2, 2024
- Everest
Table of Contents
Tall Storage Cabinet
36″ W x 18″ D x 74″ H
Use & Care Guide Maximum weight capacity of 500 lbs evenly
distributed
B0D366KWN9 36 Inch Tall Storage Cabinet
Read all instructions and warnings before proceeding.
If you do not understand any portion of the instructions, do not attempt
assembly;
EMAIL :
[email protected]t
Call : 866-456-0866.
This Use & Care Guide Guide provides instructions on how to assemble and use
your Everest™
Tall Cabinet.
It is critical that the Cabinet be assembled correctly and according to the
instructions.
The product is intended for use in working areas including offices, homes,
craft rooms, garages, etc.
The product is intended to be placed on a level floor.
WARNING!
- Strictly follow all instructions to avoid an accident, damage to property, personal injury, or death.
- Do not sit, stand, or climb on cabinet and do not let children do so. Components might fail, causing a person to fall, possibly resulting in serious injury or death.
- FOR CALIFORNIA RESIDENTS ONLY – WARNING: Cancer and reproductive harm. For full information, go to www.P65Warnings.ca.gov.
It is the consumer’s responsibility to:
- Assemble this system in accordance with provided instructions
- Maximum weight capacity of 500 lbs evenly distributed Adjustable shelf supports up to 100 lbs
- Failure to follow warning could result in serious injury
Preparation
- Find a soft surface for the assembly process to avoid any scratching (e.g. on top of a rug, a carpet, or the broken down shipping box).
- One-person assembly is suggested or feel free to invite a friend or family member to help assemble and install.
You may need
- Phillips Screwdriver
- Drill
Box Includes
UNPACKING AND ASSEMBLING YOUR PRODUCT SAFELY
When you receive your product, please proceed with caution during the
unpacking process. The frame of the item is partially assembled, with sides
that unfold both upwards and downwards. This is an integral part of the
assembly mechanism designed for your convenience. To avoid any potential
injury or damage to the product, gently remove the packaging material and
carefully allow the frame to unfold as intended. Ensure that you have ample
space to work with, avoiding any cramped or cluttered areas that may hinder
the smooth expansion of the frame. If necessary, seek assistance to stabilize
the components during this process.
STEP 1
Remove both top and bottom frames (P1, P7) and lay on their backs on a
protected surface with the sides facing up. Lift each side panel to an upright
position. STEP 2
Take the top panel (P2) and lock each side to the top frame (P1) using the
loop and tabs. Secure all six panel tabs within frame loops (See magnifi ed
view). Secure top panel with 2 Panel Screws (A) on the inside of each side
frame. Tighten with Hex Wrench (E). (See magnifi ed view) Repeat step 2 and
secure bottom panel (P3) to the bottom frame (P7) with 2 Panel Screws (A).
Tighten with Hex Wrench (E).
(See magnifi ed view) STEP 3
Install 4 leveling feet by screwing clockwise into the underside of the bottom panel (P3). STEP 4
Connect top and bottom frames and secure each side with a panel screw on the inside of the frame (see magnifi ed view). STEP 5
Flip cabinet upright. Secure top and bottom panels to frame with 8 Back Screws (B) through the pilot holes (see magnifi ed view).
STEP 6
Install the middle fi xed shelf by inserting the loop and tabs.
Secure all panel tabs with frame loops by pressing fi rmly in place. Install
adjustable shelves. Insert four Shelf Clips (C) in the frame slots at the
desired height. These will “click” in place. Locate Shelf (P6) and with the
front facing forward position the shelf above the clips and all the way to the
rear of the frame. Next, lower onto
the clips until the shelf clicks into place. Check for stability and adjust if
needed (See magnifi ed view).
STEP 7
Hinges are already installed and can be quickly connected.
Locate the four doors top left (P4), top right (P5), lower left (P8), and
lower right (P9). For all four door panels, extend the hinges in direction off
the cabinet frame to attach. It is suggested to begin with the lower left and
upper left doors, then attach the lower right and upper right doors.
The Tall Cabinet is designed for either a 2- or a 4-door opening option. To
secure doors for a 2-door opening option, link the top door assemblies with
the loop and tab to the bottom doors and secure each of them with a panel
screw. Align the hinge with the hinge plate. Press the back part of the hinge
to click into position. To release the hinge, press the back release button.
The Tall Cabinet is designed for either a 2- or a 4-door opening option.
To secure doors for a 2-door opening option, link the top door assemblies with
the loop and tab to the bottom doors and secure each of them with a panel
screw.
STEP 8
Move cabinet to the desired location. Use the leveling feet to adjust the
height to eliminate the cabinet from rocking. R to lower L to raise
Aligning Doors. If doors do not align, adjust the three screws on the panel
door hinges. Back screw adjusts back to front, the front screw adjusts left to
right, and the top screw adjusts up and down. Install Safety Strap (F).
Cabinet is designed for easy cord management. Simply punch out the 4 ports on
the back and feed electrical cords through the holes.
CLEANING
Wipe with soft cloth and a mild dish soap to keep cabinets clean.
Dry immediately with a soft, clean cloth.
CONTACT INFORMATION
EVEREST WORLD HEADQUARTERS
Kindred Products LLC
2460 M-139 Suite B
Benton Harbor, MI 49022-6444
Mailing Address
P.O. Box 827
Saint Joseph, MI 49085-0827
Customer Service
Phone: 866-456-0866
Email:
[email protected]
Website: www.Everesthome.com
Scan for Warranty Information
Warning and Disclaimer: Kindred LLC Expressly disclaims all liability for personal injury, property damage or loss, whether direct, indirect, incidental, resulting from incorrect assembly, improper use, inadequate maintenance, or neglect. 2024 Kindred. All rights reserved.