Everest and Jennings 90763450 Traveler HTC Wheel Kit Instruction Manual
- June 7, 2024
- Everest and Jennings
Table of Contents
Everest and Jennings 90763450 Traveler HTC Wheel Kit
Post-Installation Checks
- Always check both wheels before sitting in the chair to ensure both the bolt and nut are completely tight, no gaps or wobble should be present and the wheels should rotate easily without pulling or rubbing.
- Check the wheel locks before operating the wheelchair under normal use to ensure proper alignment and ability to hold the wheelchair in place.
Specifications
Part Number | 90763450 |
---|---|
Document Revision | EJ_GF2400083_HD_HTC-INS-LAB-RevA24 |
FAQ
- What should I do if components are damaged or missing?
- Contact your GF Health Products, Inc. authorized distributor immediately and do not use substitute parts.
- Can I use non-E&J replacement parts for the wheel kit?
- No, you should only use Everest & Jennings replacement parts to avoid personal injury and damage to the wheel or wheelchair.
- What is the warranty period for the wheel kit?
- The wheel kit has a warranty period of three (3) months.
For the most current and complete product information, visit www.grahamfield.com.
SAVE THESE INSTRUCTIONS FOR FUTURE USE
- WARNING: Important! Read and understand these instructions before installing the wheel kit. If the wheel kit is not properly installed, personal injury and damage to the wheel and/or wheelchair could result.
- WARNING: If components are damaged or missing, contact your GF Health Products, Inc. (“GF”) authorized distributor immediately. DO NOT use substitute parts. Use only Everest & Jennings (“E&J”) replacement parts. Non-E&J replacement parts could cause personal injury and cause damage to the wheel or wheelchair.
- WARNING: GF Health Products, Inc. assumes no responsibility for any damage or injury caused by improper assembly, installation or use of this product.
INTENDED USE
- This product is intended for wheel replacement only.
- WARNING: Make note of the placement of the wheel on the wheelchair frame, some frames have multiple threaded height positions.
- Always replace wheel kits in the same location to ensure the proper fit of wheel locks and that wheelchair arms do not come in contact with the wheels.
INSTALLATION
REMOVAL OF OLD WHEEL (SEE PICTURES 1-2 BELOW)
Fold the wheelchair to reduce the movement/play. Lay the wheelchair on the
opposite side of the wheel to be replaced, and ensure the wheel lock is
engaged on the wheel on the bottom side to ensure the chair doesn’t move or
rotate. Remove the cap cover on the wheel centre top to expose the bolt. Using
a 15/16″ socket and/or wrenches on both the bolt and the nut on the inside of
the wheelchair frame, loosen and then remove the nut and spacer from the bolt
threads. Once the nut and spacer have been removed, slowly pull the bolt out
from the frame of the chair. Keep the bolt, nut, and spacer, you will re-use
them for the new wheel assembly.
INSTALLATION OF NEW WHEEL (SEE PICTURE 3 BELOW)
Refer to picture 3 to ensure proper placement of the bolt, wheel, nut, and
spacer. Once the wheel kit has been assembled, slowly lower the bolt through
the hole in the side frame of the wheelchair. When the bolt has been pushed
through the frame, insert the spacer, then screw the nut onto the threaded
part of the bolt on the inside of the frame. Using a 15/16″ socket and/or
wrench on the bolt head and nut, tighten them as much as possible while still
allowing the wheel to rotate. Ensure the wheel rotates and doesn’t have any
pull or gap/wobble before placing it back upright on all 4 wheels. Place the
cap cover back on the wheel and tap lightly with a rubber mallet to secure it
to the wheel.
WARNING: Always check both wheels before sitting in the chair to ensure
both the bolt and nut are completely tight, no gaps or wobble should be
present and the wheels should rotate easily without pulling or rubbing.
WARNING: Check the wheel locks before operating the wheelchair under
normal use to ensure proper alignment and ability to hold the wheelchair in
place.
WARRANTY
SCOPE OF WARRANTY
- GF Health Products, Inc. (“GF”) warrants to the original purchaser only that it will replace or repair components, at GF’s sole discretion, that are defective in material or workmanship under normal use and service. All warranties are conditioned upon the proper use of the products strictly under good commercial practice and applicable GF instructions and manuals, including proper use and maintenance. To the extent that a third party warrants a component, GF conveys all of its rights under that warranty to the original purchaser, to the extent permitted.
- This limited warranty shall only apply to defects that are reported under the provisions outlined in this warranty document, within the applicable warranty period and which, upon examination by GF or its authorized representative, prove to be a warranty item. (See Obtaining Warranty Service below) This limited warranty is not transferable.
- The warranted components and periods are set forth below:
- Wheel Kit:…………………………………………….three (3) months
- Labor is not included in the warranty.
- The warranty period is as designated above. If a part is replaced under warranty, the original warranty period will not be affected. All other replacement parts will be subject to the warranty period specified. The applicable warranty period shall commence from the date of shipment to the original customer unless there is an expiration date on the component in which case the warranty shall expire on the earlier of the warranty period or the expiration date.
- Please see USER MANUAL for detailed Warranty Information or contact your GF representative at 1-770-368-4700.
CONTACT
Manufactured For
- GF Health Products, Inc.
- One Graham-Field Way, Atlanta, GA 30340
- +1 770.368.4700
- Information contained herein is subject to change without notice.
- The most current and complete product information can be found on our website
- www.grahamfield.com
© 2024, GF Health Products, Inc. All Rights Reserved. Everest & Jennings is a registered trademark of GF Health Products, Inc. EJ_GF2400083_HD_HTC-INS-LAB- RevA24
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>