BLAZE Ci4 and Ci4-V Loudspeaker Installation Guide
- June 30, 2024
- BLAZE
Table of Contents
Ci4 and Ci4-V Loudspeaker
“`html
Specifications
- Model: Ci4 & Ci4-V Loudspeaker
- Brand: Blaze Audio
- Wire compatibility: Up to 4 sq. mm wire with an outside cable
diameter of up to 20 mm
Product Information
Congratulations on your new Ci loudspeaker system from Blaze
Audio. The Ci series is a feature-packed range of loudspeakers
designed for use in a variety of applications. Emphasis is placed
on discreet modern design, ease of installation, wide and uniform
coverage, and excellent sound quality without electronic signal
processing.
Included in the box: Two speakers, Two Sliders, Mounting screws,
Mounting template, Safety letter
Getting Started
-
Remove the front cover to access the cable terminal by pushing
the cover from the side of the cabinet. -
Ensure the amplifier is turned off.
-
Run the speaker cable through the tube positioned at the rear
of the cabinet to the terminal at the front baffle. -
If using sliders, mount the speaker cables to the terminal. If
using mounting points, install the speaker first and then mount the
cable to the terminal.
Installation
The Ci series can be mounted in corners, on walls, and ceilings
with integrated mounting points or slider bars. They can also be
coupled together to extend coverage.
Vertical or Horizontal Installation in Corners
-
Remove the front cover to access mounting holes on the left and
right sides of the cabinet. -
Place the mounting template in the desired position and mark
drilling positions through the six mounting holes.
Mounting in Non-90 Degree Corners
If the wall or ceiling is soft or you want to mount away from a
corner, slide the speaker onto sliders for installation.
Mounting the Cabinets Together
The Ci series speakers are designed for uniform and wide
controlled dispersion. They can be coupled together for expanded
coverage. Three cabinets can be mounted together to cover 270
degrees around a free-standing corner using 9×3 mm bolts and
integrated mounting points.
FAQ
Q: What should I do if I connect the amplifier output
incorrectly?
A: If reversed, stereo imaging will be blurred, and bass output
will be dramatically reduced. Always connect red amplifier output
(+) to red speaker input and black amplifier output (-) to black
speaker input.
“`
Ci4 & Ci4-V Loudspeaker
Installation Manual
Table of contents
Introduction
3
Getting started
4
Installation
5
Mounting the cabinets together 6
Cables
7
Operation
7
Specifications
10
Introduction
Congratulations on your new Ci loudspeaker system from Blaze Audio. The Ci
series is a feature packed range of loudspeakers designed for use in a large
variety of applications. Emphasis is placed on discreet modern design, ease of
installation, wide and uniform coverage and excellent sound quality without
the use of electronic signal processing.
Included in the box: Two speakers Two Sliders Mounting screws Mounting
template Safety letter
The series provides a 100 degree vertical x 100 degree horizontal dispersion
and comprises 2″, 4″, and 5″ models, with an optional high impedance mode. The
patented 90 degrees triangular ABS cabinet with built-in sliders not only fits
perfectly into vertical and horizontal corners without showing visible
brackets, but also offers a wealth of other unique placement capabilities.
These include coupling 2-4 speakers together to increase coverage to 180, 270,
or even 360 degrees when mounted on walls, ceilings, free-standing corners,
and more. (excluding Ci2, which allows a maximum of 2 coupled cabinets for 180
degree coverage). For enhanced bass performance, the Ci series can be teamed
indoors with our C8S and C12S subwoofers.
Getting started
Connections. The Ci models are fitted with a screw terminal on the front
baffle. Contacts will accept up to 4 sq. mm wire with an outside cable
diameter of up to 20 mm.
Important: Always connect the red amplifier output (+) to the red speaker
terminal input and the black amplifier output (-) to the black speaker input.
If reversed, the stereo imaging will be blurred and the bass output will be
dramatically reduced.
How to connect the cables. It is important that you run the speaker cables
through the port BEFORE mounting your new Blaze Audio speakers! The speakers
are equipped with discreet cable terminals placed on the front baffle behind
the front cover and it is not possible to run the cables to the terminals
once the speakers have been installed.
1 Remove the front cover to access the cable terminal: Push the cover from the
side of the cabinet to squeeze it out of the grove.
2 Make sure the amplifier is turned off.
3 Run the speaker cable through the tube positioned at the rear of the cabinet
to the terminal at the front baffle.
*Note that it is easier to install the speaker first and mount the cable to the terminal after the speaker is mounted to the wall.
4 If you use the sliders, you can mount the speaker cables to the terminal at
this point. If you use the mounting points, it is easier to install the
speaker first and mount the cable to the terminal after the speaker is mounted
to the wall.
Installation
The Ci series can be mounted either in corners, on wall and ceilings with the
integrated mounting points or the slider bars. They can also be coupled
together to extend coverage.
The Ci4 and Ci4-V are light, but please make sure that the wall or ceiling is
solid and can support the weight of the speaker before installing. Also, make
sure that you comply with all local health and safety regulations. (See the
Safety Letter included in the packaging.) The low weight and the sliders allow
the products to be installed easily by one person.
Vertical or horizontal installation in corners.
If you prefer to mount the speaker in a corner, you should:
1 Remove the front cover and you’ll see the mounting holes in the left and
right hand side of the cabinet.
2 Place the mounting template in desired position and mark drilling positions
by shading through the six mounting holes
2 · Drill holes in the wall using 4 mm rawl plugs and the enclosed 3,5 mm flat
head screws.
· Reposition the speakers in desired position and mount the screws.
Mounting in corners that are not exactly 90 degrees:
· If the corner is less than 90 degrees, simply place the speaker cabinet as
deep in the corner as possible and use all mounting points. This will leave a
little space behind the cabinet and the walls, but the speakers will still
appear with a nice finish in the corner.
· If the corner is more than 90 degrees, we recommend mounting only one of the
sides of the speaker cabinet onto the wall and leave some air behind the
other side of the cabinet. This will not be visible from the front, and the
speakers will still present themselves with a nice finish.
If the wall or ceiling is soft, or if you want to mount the speakers on the wall or ceiling away from the corner.
Slide the speaker onto the sliders.
· Mount the sliders to the wall or ceiling using the provided template. Ensure
the arrow on the slider points towards the front of the speaker.
· If the wall is solid, one slider is sufficient to hold the speaker.
· Slide the speaker onto the sliders
· Finally fix the speaker to the wall or ceiling by screwing through the
cabinet and slider into the wall or ceiling, using the upper and lower
mounting points.
Mounting the cabinets together
Our Ci series speakers are designed with an emphasis on uniform and wide
controlled dispersion. The acoustic design allows the speakers to be coupled
together to expand coverage:
· One Ci cabinet offers 100×100 degree dispersion.
· Two Ci cabinets can be coupled together back to back and then mounted flush
onto walls and ceilings while offering 200 degrees of coverage with minimum
phase cancellation.
· Mount the speakers back to back on wall or ceiling using either the sliders
or integrated mounting points. Use 4 mm blots between 38 and 42 mm long to
screw the cabinets together.
Likewise, three cabinets can be mounted together to cover 270 degrees around a free-standing corner. Simply couple three cabinets together using 9×3 mm bolts and mount the speakers to the corner with the integrated mounting points.
Connect the red (+) and black (-) speaker cable to the left + and right – screw terminals. Use the right + – terminals to link to another speaker.
Cables
Speaker cables present the amplifier with different loads. Cables with high
capacitance, high inductance and high impedance have a strong negative
influence on sound quality as well as amplifier reliability. In order to get
the most out of the speaker system, avoid using thin speaker cables.
As a rule of thumb, 2 mm2 (14 AWG) cable can be used for lengths up to 20
meters. 4 mm2 (11 AWG) cable should be used for lengths over 20 meters. For
lengths over 50 meters, most amplifiers will become unstable and sound quality
is reduced significantly.
To minimize power loss and response variations, please refer to the following
table for guidance, showing the maximum recommended cable length relative to
impedance and cable thickness:
Cable size/load 2 sq mm. 2,5 sq mm. 4 sq mm.
8 20 m / 65 ft. 30 m / 100 ft. 60 m /200 ft.
4 10 m /32 ft. 15 m /50 ft. 30 m /100 ft.
2 5 m / 16 ft. 7,5 m / 25ft. 15 m / 50 ft.
Operation
Tweeter protection. Ci4 and Ci5 feature a tweeter protection circuit. If a
microphone is used, or if the speaker is used in environments with very high
level of background sound, we recommend turning on the protection circuit. For
home installations, we recommend turning off the protection.
Tweeter Protection
To enable, move the PTC switch to ON. To disengage, move the switch to OFF.
100V
70V
Outdoor mounting. The Ci4 and Ci5 are IP65 rated, so they can be placed
outside. (See the Safety Letter included in the packaging.) If installed
outdoors, the insulation of the cabling should be resistant to water as well
as the effects of temperature and ultraviolet radiation from the sun.
Recommended insulations are: UV stabilized polyethylene, neoprene, TeflonTM,
SiliconTM, and HypalonTM. The following materials are not recommended, because
of potentially shorter life expectancy in outdoor environments: rubber, PVC
(polyvinylchloride), polypropylene, polyurethane, and nylon. UV-stabilized
polypropylene may be acceptable.
Mode selection. Ci4-V & Ci5-V can be driven in 8 ohm or 70 V or 100 V mode.
The input tap selection switch is placed behind the grille. On Ci4-V the taps
are 3,75, 7,5, and 15 watt output in 70 V mode and 7,5 and 15 W output in 100
V mode. On Ci5-V the taps are 3,75, 7,5, 15 and 30 W output in 70 V mode and
7,5, 15 and 30 W output in 100 V mode. The rotary switch is operated with a
flat-head #7 screw driver.
Safety wire. In installation terms, the top-boxes are as much brackets as they
are speakers, because they mount flush to the walls and ceilings, so no safety
wire is needed (just like on traditional speaker installations, you don’t use
a safety wire from a bracket to the wall).
Speaker presets. Recommended loudspeaker presets are available at blaze-
audio.com/support and are designed for use with Blaze Audio’s PowerZoneTM
Connect DSP-enabled amplifier series.
Recommended amplifier. The Ci speaker series has a high minimum impedance,
making them an easy load for amplifiers. We recommend using Blaze Audio’s
PowerZoneTM Connect DSP-enabled amplifiers with power ratings that exceed the
loudspeakers’ power handling capacity (see specifications). As with all
loudspeaker systems, power handling depends on the quality and size of the
amplifier. If the amplifier is overdriven and runs into clipping, the drivers
can be damaged, even if the amplifier’s output is lower than the speaker’s
power handling capacity. When selecting an amplifier, keep in mind that a
higher power amplifier operating without distortion will typically sound
better and cause less damage to the loudspeaker than a lower power amplifier
that is constantly clipping.
Warranty. For warranty information, please refer to your local Blaze Audio
distributor or dealer, or contact us directly.
Service. Woofers can be easily replaced by unscrewing them from the baffle
using a Hexagon H3 bit. The tweeter is clicked into the horn section of the
baffle from the rear of the baffle. To access the tweeter, remove the baffle
by unscrewing the four Philips screws.
Spare parts for your Blaze Audio speakers are available through your local
Blaze Audio distributor or dealer. Please contact us directly, in case you are
not able to source spare parts locally.
Turn the tweeter counter-clockwise to remove it from the baffle. Reinstall the
new tweeter by pressing it towards the horn section of the baffle and turn it
clock wise until you hear a “click”.
The crossover is removed by unscrewing the Philips head screws and removing
the cables from the drivers.
Specifications
145 mm 400 mm
130 mm
190 mm
Ci4 /Ci4-V
Power handling, IEC268: Power handling, peak: Sensitivity, 2,83 V/1 m: Maximum
SPL, long term: Maximum SPL, peak: Frequency response: Nominal impedance:
Dispersion: Recommended amplifier: Measurements: Weight:
Colour:
60 W 240 W 86 dB 105 dB 111 dB 60-20.000 Hz 8 100° vertical / 100° horizontal 30-80 W 400 x 190 x 145 mm (15.75 x 7.48 x 5.71 in) Ci4: 2,7 kg (5.95 lb) Ci4-V: 3,15 kg (6.94 lb) Black White
Ci4-V transformer taps: 70 V: 3,75, 7,5, 15 W 100 V: 7,5, 15 W
Contents of the manual are subject to change without notice. Blaze Audio does not accept any liability for loss or damage caused or alleged to be caused directly or indirectly by these instructions.
Rev A 30/05/2024
Blaze Audio HQ, Pascal A/S, Ellekaer 6, DK-2730 Herlev, Denmark. hello@blaze-
audio.com
Blaze Audio Americas, Pascal Inc.,
888-500-0109, help@blaze-audio.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>