Gardyn GHA02 Indoor Garden System Growing Vegetables Herbs and Flowers Installation Guide

Gardyn GHA02 Indoor Garden System Growing Vegetables Herbs and Flowers

Specifications

• Light protective cap
• Safety straps
• Camera
• LED light bar
• Main switch
• Light switch
• Lower blade
• Water pump
• Upper blade
• Rod connector
• Metal rod
• Columns
• Lid
• Wood cap to watering compartment
• Lid locks
• Water tank

Product Usage Instructions

Carefully unpack the parts in the specified order as shown in the video. This includes the LED light bar, lid with wood cap, columns, metal rod, upper blade, metal plates, plugs, plant food spoon, water tank, power supply, and iPods.

Remove any tape and open the lid locks to mount the lid onto the water tank. Close the lid locks securely.

• Gently pull on the irrigation hoses to ensure they are straight inside the columns without any kinks.
• Hold the column vertically and plug the hose connector onto the tube inside the column’s base until snug. Twist the column to secure it.
• Ensure all open slots face the front of the lid.
• Insert the metal rod onto the back of the columns, slide metal plates into each column, and insert plugs to secure.
• Remove the camera’s protective film and attach the upper blade to the light bar, then clip it onto the metal rod.
• Ensure the upper blade is fully clipped onto the metal rod.

Check Progress

Ensure that all components are assembled correctly as per instructions including camera film removal, alignment of columns and vine designs, mounting of LED light bar with protective cap, connection of metal rod to upper blade and columns, lowering of water pump into the tank, and removal of any cardboard.

FAQ

• Q: What should I do if the LED light is not turning on?
• A: Check the main switch and power supply connection to ensure they are properly connected. If the issue persists, contact customer support for assistance.
• Q: How often should I water my plants in Gardyn Studio?
• A: Monitor the water level in the tank regularly and refill as needed to ensure proper hydration for your plants.

Welcome to the Gardyn family!

• Get ready to discover the joy of growing your food.
• From seed to harvest and beyond, we’ve got you covered with comprehensive resources, essential accessories, and, of course, Kelby.
• We are thrilled you’re here and can’t wait to see your progress!

Let’s get Gardening!

OVERVIEW

Meet Your Garden Studio

Reminder: Do not plug the device in until instructed to do so.

Unpacking

• Carefully unpack the parts following the order in the video.

Mount & lock the lid

1. Remove the tape and open the lid locks to mount the lid onto the water tank, then close the lid locks.
2. Remove the cardboard and lower the water pump.
   The cardboard’s appearance may vary slightly from the one shown.

Assemble & connect the columns

1. Gently pull on the end of the irrigation hoses to ensure they are straight inside the columns and avoid any kinks.
2. Align the arrows, then twist. When completed, the arrows will no longer align.
3. Hold the column vertically and plug the hose connector onto the tube inside the column’s base until snug.
4. Twist the column to secure it. When completed, the arrows will no longer align.
5. Ensure all open slots face the front of the lid, as shown.

Attach light bar & upper blade

1. Insert the metal rod onto the back of the columns, then slide the metal plates into each column and insert plugs to secure.

2. Hold the light vertically so that the camera is near the top.
   Carefully yet firmly slide the bottom of the light onto the lower blade attached to the lid.
   Push until you see the grey post in the notch of the light bar.

3. Remove the camera’s protective film.

4. Attach the upper blade to the light bar, then clip it onto the metal rod.

5. Ensure the upper blade is fully clipped onto the metal rod.

Check Progress

At this stage, you should see the following

• The camera’s protective film is removed.
• The 2 columns have all slots facing the light and all vine designs aligned.
• The LED light bar is mounted and the light protective cap is flush with the top of the light bar.
• The metal rod is connected to the upper blade and columns by 2 metal plates and plugs.
• The water pump is lowered into the tank and the cardboard is removed.
• The lid locks are pushed against the sides of the water tank in the locked position.

WARNING

• Prevent the device from tipping over.
• The device must be securely attached to the wall. Use the safety straps provided with the product and the appropriate hardware to affix to your wall type.
• Never let children hang onto the lights or columns. Never let children climb on the device.

If you’ve completed each of these steps, you’re ready to secure your device to the wall using the safety straps.

Fill tank & turn on

• DO NOT ADD PLANT FOOD when you start your Gardyn.
• The app will help you learn when it’s time to start feeding your plants later on.

• The device is turned ON/OFF by flipping the main switch located on the back of the water tank.
• Make sure the main switch is in the OFF [O] position before plugging in or unplugging the device to the power supply. Once the device is plugged in, turn it on by flipping the main switch to the ON [ I ] position.
• The main switch will illuminate and your light bar will blink once it is fully powered up.

Install your plants

• If you haven’t already, open and unpack the box containing the 16 yPods.
• Insert 1 yPod into each of the open slots on both columns. To insert, twist each yPod until it sits flush with the column.

Tip

• Check out our placement guide to find your plants’ ideal spots based on your starter kit!

• Time to plant! Place the yCubes into the yPods. yCubes are correctly inserted when they sit flush with the yPod.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>