Winplus T401AI 1T1R SDIO WIFI Module Owner’s Manual

Winplus T401AI 1T1R SDIO WIFI Module

Product Specification

IEEE 802.11b/g/n 1T1R SDIO WiFi Module

FCC Information

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including
   interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or change to this equipment. Such modifications or change could void the user’s authority to operate the equipment.

RF Exposure Information: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. In order to avoid exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm during normal operation. This module is for internal use only and not sold outside.

Antenna Information
It is a 2.4GHz FPC antenna (IPEX port).

Trace antenna designs: Not applicable.

RF exposure considerations: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The antenna(s) used for this transmitter must not be collocated or operating in conjunction with any other antenna or transmitter.

Note: The host product manuals must include a statement to alert users of FCC RF exposure compliance.

Product/PMN
T401AI WIFI Module

Model no./HVIN: BT534217

Labeling Requirements
The system integrator must place an exterior label on the outside of the final product housing the T401AI WIFI Module with the following content:

• NOTICE: The host product must ensure that FCC labeling requirements are met.
• Additional testing, Part 15 Subpart B disclaimer: The modular transmitter is only FCC authorized for specific rule parts (FCC Part 15.247) listed on the grant, and the host product manufacturer is responsible for compliance with any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed when it contains digital circuitry.
• Information on test modes and additional testing requirements: When testing the host product, the host manufacturer should follow FCC KDB Publication 996369 D04 Module Integration Guide for testing the host products. The host  manufacturer may operate their product during themeasurements.

FAQ

• What are the FCC compliance requirements for this WiFi module?
  The device complies with Part 15 of the FCC rules, ensuring it does not cause harmful interference and accepts any interference received.

• What is the recommended human proximity to the antenna during operation?
  To avoid exceeding FCC radio frequency exposure limits, human proximity to the antenna should not be less than 20cm during normal operation.

• Are there any specific labeling requirements for the host product housing this WiFi module?
  Yes, the host product must have a clearly visible exterior label displaying specific content related to FCC compliance and testingrequirements.

Product Specification

IEEE 802.11b/g/n 1T1R SDIO WiFi Module
FG89FTSM33-W4 is a highly integrated and excellent performance Wireless LAN (WLAN) SDIO network interface device. High-speed wireless connection up to 72.2 Mbps .
The general hardware for the module is shown in Figure 1. This WLAN Module design is based on Realtek RTL8189FTV -VQ1. It is a highly integrated single- chip 1*1 MIMO (Multiple In Multiple Out) Wireless LAN (WLAN) SDIO network interface controller complying with the 802.11n specification. It combines a MAC, a 1T1R capable baseband, and RF in a single chip. It is designed to provide excellent performance with low power Consumption and enhance the advantages of robust system and cost-effective.

This specification is based on additional references listed as below.

• iEEE 802.11b
• iEEE 802.11g
• iEEE 802.11n

Power Consumption

Layout reference

Application Circuit

FCC Information

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or change to this equipment. Such modifications or change could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Information:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm during normal operation. This module is for internal use only and not sold outside.
Product/PMN: T401AI WIFI Module
Model no./HVIN: BT534217

Antenna Information
It is 2.4GHz FPC antenna(IPEX port).

Module procedures :
The module has its own RF shielding, which belong to signal module Standard requires: Clear and specific instructions describing the conditions, limitations and procedures for third-parties to use and/or integrate the module into a host device (see Comprehensive integration instructions below).
Resolve: Supply example as follows:

Installation Notes:

1. BT534217 Module Power supply range is DC 3.1V~3.5V, when you use BT534217 Module design product, the power supply cannot exceed this range.
2. When connect BT534217 Module to the host device, the host device must be power off.
3. Make sure the module pins correctly installed.
4. Make sure that the module does not allow users to replace or demolition.

Trace antenna designs: Not applicable.

RF exposure considerations
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The antenna(s) used for this transmitter must not be collocated or operating in conjunction with any other antenna or transmitter.
Note: the host product manuals must include a statement in order to alert the users of FCC RF exposure compliance.
The system integrator must place an exterior label on the outside of the final product housing the T401AI WIFI Module. Below is the content that must be included on this label. The host product Labeling Requirements: NOTICE: The host product must make sure that FCC labeling requirements are met. This includes clearly visible exterior label on the outside of the final product housing that displays the contents shown in below:

Contains FCC ID: WUI-T401AI
Information on test modes and additional testing requirements: When testing host product, the host manufacture should follow FCC KDB Publication 996369 D04 Module Integration Guide for testing the host products. The host manufacturer may operate their product during the measurements. In setting up the configurations, if the pairing and call box options for testing does not work, then the host product manufacturer should coordinate with the module manufacturer for access to test mode software.

Additional testing, Part 15 Subpart B disclaimer:
The modular transmitter is only FCC authorized for the specific rule parts (FCC Part 15.247) list on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed when contains digital circuity.
Information on test modes and additional testing requirements:
When testing host product, the host manufacture should follow FCC KDB Publication 996369 D04 Module Integration Guide for testing the host products. The host manufacturer may operate their product during the measurements.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>