Winplus TTGEN2 Wireless Module User Manual
- March 29, 2024
- WINPLUS
Table of Contents
TTGEN2 Wireless Module
“`html
Specifications
- Module: TTGEN2
- File name: Product specification
- Version: V1.2
- Editor: Henry Ho
- Finished date: 2024-03-21
- Participator: Valid from 2024-03-21
Product Information
B828 wireless module is designed based on B828 chipset. This
wireless module can support communication over 100 meters. It
operates at 2412-2462MHz with a high wireless data rate.
Note: The above pictures are for reference only.
Features
Functional Block Diagram
Detailed Specifications
Specification:
- Wireless module based on B828 chipset
- Supports communication over 100 meters
- Operates at 2412-2462MHz
- High wireless data rate
Storage Temperature and Humidity
-
Storage Condition: Moisture barrier bag must be stored under
30°C, humidity under 85% RH. Shelf life for dry packed product is
12 months from the bag seal date. -
If humidity indicator cards read > 30%, temp < 30°C,
humidity < 70% RH, products require baking before mounting.
Baking condition: 125°C, 12 hours.
FCC Information
This module complies with Part 15 of the FCC rules. It must not
cause harmful interference and must accept any interference
received. Changes or modifications not approved by the responsible
party could void the user’s authority to operate the equipment.
RF Exposure Information
The equipment complies with FCC RF radiation exposure limits.
Human proximity to the antenna should not be less than 20cm during
normal operation.
Antenna Information
It is a 2.4GHz Copper tube antenna (IPEX port), model number
CH16HL.
Installation Instructions
-
Power supply range: DC 3.1V~3.5V
-
When connecting to the host device, ensure it is powered
off. -
Ensure correct installation of module pins.
-
Module should not allow users to replace or dismantle.
Usage Instructions
- Ensure the product is stored in the specified conditions.
- Follow FCC guidelines for operation and interference.
- Maintain safe distance from the antenna during operation.
- Follow installation notes for proper integration with host
devices.
FAQ
Q: Can the module be used for external purposes?
A: No, this module is for internal use only and should not be
sold outside.
“`
Specification
MODULE OF TTGEN2
TTGEN2 Specification
File status [ ] Draft [ ] Published [ ] Pending
File name Product specification
Version V1.2
Editor
Henry Ho
Finished date
2024-03-21
Version V1.2
Editor
Henry Ho
Participator Valid from 2024-03-21
Remark
Specification
0 Amendment 1 General Description
B828 wireless module is designed base on B828 chipset. This wireless module
can support far than 100M communication. It operates at 2412-2462MHz and high
wireless data rate.
Note: The above pictures are for reference only
2 Feature
· Operating Frequencies: 2.412~2.462GHz · Host Interface is USB, complies with
USB2.0 · Connect to the external antenna through the IPEX connector · Power
Supply:3.3V±0.2V
Functional Block Diagram
3 Specification
Specification
Specification
4 Drawing 4.1 Mechanical Specifications
Specification
5 Remark
5.1 Storage Temperature and Humidity 1. Storage Condition: Moisture barrier
bag must be stored under 30, humidity under 85% RH. The calculated shelf life
for the dry packed product shall be a 12-months from the bag seal date.
Humidity indicator cards must be blue, 30% . 2. Products require baking before
mounting if humidity indicator cards reads > 30% temp < 30, humidity < 70% RH,
over 96 hours. Baking condition: 125, 12 hours. Baking times: 1 time.
Specification
FCC Information
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to operate
the equipment. The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications or change to this equipment.
Such modifications or change could void the user’s authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: -Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver. -Connect the
equipment into an outlet on a circuit different from that to which the
receiver is connected. -Consult the dealer or an experienced radio/TV
technician for help.
RF Exposure Information: This equipment complies with FCC RF radiation
exposure limits set forth for an uncontrolled environment. In order to avoid
the possibility of exceeding the FCC radio frequency exposure limits, human
proximity to the antenna shall not be less than 20cm during normal operation.
This module is for internal use only and not sold outside.
Antenna Information It is 2.4GHz Copper tube antenna(IPEX port), model number
CH16HL.
The modular must be installed in the host that assign by Company name: Winplus
Co., Ltd. Product/PMN: MODULE OF TTGEN2 Model no./HVIN: TTGEN2 if other host
types used would need further evaluation and possible C2PC if they are not
significantly similar to the one tested.
Module procedures: The module has its own RF shielding, which belong to signal
module Standard requires: Clear and specific instructions describing the
conditions, limitations and procedures for third-parties to use and/or
integrate the module into a host device (see Comprehensive integration
instructions below). Resolve: Supply example as follows: Installation Notes:
- TTGEN2 Module Power supply range is DC 3.1V~3.5V, when you use TTGEN2
Module design product, the
power supply cannot exceed this range. 2) When connect TTGEN2 Module to the host device, the host device must be power off. 3) Make sure the module pins correctly installed. 4) Make sure that the module does not allow users to replace or demolition.
Trace antenna designs: Not applicable.
The system integrator must place an exterior label on the outside of the final product housing the TTGEN2 Modules. Below is the content that must be included on this label. The host product Labeling Requirements: NOTICE: The host product must make sure that FCC labeling requirements are met. This includes clearly visible exterior label on the outside of the final product housing that displays the contents shown in below:
Contains FCC ID: WUI-TTGEN2
Specification Information on test modes and additional testing requirements:
When testing host product, the host manufacture should follow FCC KDB
Publication 996369 D04 Module Integration Guide for testing the host products.
The host manufacturer may operate their product during the measurements. In
setting up the configurations, if the pairing and call box options for testing
does not work, then the host product manufacturer should coordinate with the
module manufacturer for access to test mode software.
Additional testing, Part 15 Subpart B disclaimer: The modular transmitter is
only FCC authorized for the specific rule parts (FCC Part 15.247) list on the
grant, and that the host product manufacturer is responsible for compliance to
any other FCC rules that apply to the host not covered by the modular
transmitter grant of certification. The final host product still requires Part
15 Subpart B compliance testing with the modular transmitter installed when
contains digital circuity.
Information on test modes and additional testing requirements: When testing
host product, the host manufacture should follow FCC KDB Publication 996369
D04 Module Integration Guide for testing the host products. The host
manufacturer may operate their product during the measurements.
IC Information
-English: This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: – This device may not cause interference. – This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
-French: Cet appareil contient un ou des émetteurs/récepteurs exempts de licence conformes aux RSS exempts de licence d’Innovation, Sciences et Développement économique Canada. Le fonctionnement est soumis aux deux conditions suivantes : – Cet appareil ne doit pas provoquer d’interférences. – Cet appareil doit accepter toutes les interférences, y compris les interférences susceptibles de provoquer un
fonctionnement indésirable de l’appareil.
Cet équipement est conforme aux limites d’exposition aux rayonnements IC
établies pour un environnement non contrôlé. Cet équipement doit être installé
et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement
et votre corps.
TTGEN2 MODULE OF TTGEN2 Responsible Party: Horizon Brands 2975 Red Hill Ave.,
Ste. 100, Costa Mesa, CA 92626, U.S.A. Tel: 1.866.294.9244