DALEN X30 Aladdin Magic Light Instruction Manual

DALEN X30 Aladdin Magic Light

Preparations for installation

Accessories check before opening box.

• main machine of projector light
• lamp cover 、decoration board
• fixing bracket
• remote controller
• batteries for remote (carbon zinc AAA batteries *2pcs)
• screw kit for quick installation

Remote controller preparations

①Press the groove to open battery box.

②Install two carbon zinc AAA batteries and put the lid on.

Installation Sequences

1. Switch off the light power ( or turn off the circuit breaker) .

2. Install the fixed bracket to the ceiling.
   
   

3. Take out the projector light from package.
   ① open the lamp cover by rotating it clockwise；
   ② open the decoration board by rotating it anticlockwise
   

4. Install the main device of projector light
   
   ①Lift the projector light with both hands pass the bracket plug through the round hole in the middle of the light.
   ②Lift the main device up until hearing “click” sound
   ③Push the control stick on the fixing bracket to LOCK position and lock it.
   ④Confirm the main device is in horizontal balance state.

5. Connect the bracket plug with the socket inside the main device.
   Please do not rotate the projector violently after the plug connected.
   (connection box may fall down)
   If you need to adjust direction by large angle, please pull out the plug first.
   

6. Install the lamp cover
   

7. Adjust the glass-covered area(projection window) direction towards the wall, installation finished.

Tear off the protective film on projection window.
Switch on the light power (or turn on the circuit breaker)

Initial Setting

Start the system, it will show「Now Loading…」on the screen, after system reading, please operate according to voice and image instructions.

1. Hold the remote controller within 50cm distance from the main device，long press Home button and previous page button .
   The state light on remote controller will start flickering   after a “ding”sound, match successfully.
   

2. focusing and definition adjustment

Press focusing button , then press direction buttons (left and right) to adjust the image to high definition state.

3. Image position adjustment
   
   Press focusing button to show the focusing image, press direction buttons to adjust the image position up and down.

4. Image keystone correction
   
   Select the four corners of image via direction button , click “OK”, you can choose corresponding corner and adjust balance via direction button , press OK button and finish setting for this corner.
   Other corners can be adjusted like this. Press “down” button ， click “OK” to enter the next step .

5. connect to network
   

Light Operation

Light on ・ Light off

Please turn on the light power when remote control operation using remote controller.

Press the switch button turn on the light in warm white (light mode can be customized)*

Press the switch button again to turn off the light.

Brightness & color temperature remote controller

press light mode button The light will be warm white (light color can be customized) in the order of warm light, whole light and night light.

press light brightness button The light will get brighter till the brightest and back to the lowest brightness, circle like above.

*Light brightness and color can be customized via “light setting ”function in “system setting” on the homepage.

Display operation

Select brightness adjustment in “light setting” function in “setting” on the homepage

Adjust brightness and color temperature, save.

Power

Power OFF
Remote controller operation

Wireless Screen-Casting

Casting operation

Disassembly

1. Switch off the light power (or turn off the circuit breaker).

2. Rotate to the left and take the cover off.
   ①Take down the lamp cover
   ②Take off the decoration board.
   

3. Pull out the connector plug from the socket inside the main device.
   

4. Take down the main device from the fixing bracket.
   ①Hold the main device by one hand, grab the balance grip with the other hand.
   ②Push the control sticker in the connection box to OPEN position while holding the balance grip, then unlock.
   ③Hold the main device carefully, take it down.
   

5. Take off the fixing bracket from the ceiling.
   Loosen the four screws and take the fixing bracket off.
   

Abnormal

wall switch and try remote controller again
There may be shelters between the remote controller and main device.| Remove the shelter and put the remote controller close to main device
Bluetooth between remote controller and main device is disconnected.
| ①Put the remote controller within 50cm distance from the main device, long press the homepage button and return button at the same time. ②Release the button when the state light on remote controller starts flickering, after hearing “ding”sound, match successfully.
If the projector still fails to be turned on, press the state light on remote controller directly. ( The state light is red when standby and turns green when the device is on. )

Factory Reset

1. Enter the setting APP via remote controller.
2. Enter “Other” option.
3. .Select “factory reset”, waiting for the countdown, click “confirm” to finish factory reset.
   

System Update

Online Update

System Update

1. Enter the online update APP via remote controller.
2. Click “check for updates” .
3. Select “online update” to finish the system update.
   

RC Spec.

Specifications

Product name ： DALEN Aladdin magic light
Model ：X30
Power ：100W
Input ： 220 – 240V~，50/60Hz
Light source ： 80 × 1W/ LED module+7 2 ×0 . 2W/ LED module
Executive standard: GB 17625 . 1 – 2012;GB/T 17743 – 2021; GB 7000 . 1 – 2015;GB 7000 . 201 – 2008；
GB 4943 . 1 – 2011;GB/T 9254 – 2008

Precautions

• Please use the power line with national electricity standard to ensure the device power’ s stability .
• Please use exactly the power supply type marked on the device .
• Please do not disassemble the device by yourself, or you will lose official warranty service .
• To prevent electric shock , please avoid water splashing on the device as it’ s not waterproof.
• Please turn off the device power or the whole power if you won’ t use it for a long time .
• Please use the original protective cushion package during deliver y .
• Please contact customer service if you find the product broken, do not fix it by yourself.

Harmful substances in the product

ethers (PBDE)**
outer cover|

O

|

O

|

O

|

O

|

O

|

O

electric board module|

O

|

O

|

O

|

O

|

O

|

O

battery|

O

|

O

|

O

|

O

|

O

|

O

remote controller|

O

|

O

|

O

|

O

|

O

|

O

accessories|

O

|

O

|

O

|

O

|

O

|

O

This form follows SJ/ T 1 1 3 6 4
O： Indicates that the content of the harmful substances in all materials of the components is below the limit requirements in GB/ T 2 6 5 7 2 .
X： Indicates that the content of the harmful substances in at least one material of the components exceeds the limit requirements in GB/ T 2 6 5 7 2 .

The number in this mark indicates the product environmental protection lifetime is 10 years in normal use. Some components may have environmental protection use limits mark, please refer to the number in that mark. Due to different models, the product may not include all above components besides the main device, please refer to the actual product sales

Warranty Card

DALEN Aladdin Magic Light Warranty Policy

1. If the product has quality problems within 7 days from purchase, consumers can choose to refund as the invoice price or replace it with another product of the same model and specifications.
2. Warranty period: 1 2 months from the date of purchase.
3. If you apply for a 7 – day return for no reason, please make sure that the film is undamaged , the product and accessories are complete; Within 1 5 days from purchase, if the product has any quality problem, consumers can choose to replace it with another one of the same model and specifications.
4. There is no damage or scratches on the product itself, accessories, product appearance or on the package.
5. During the free warranty period, the returned product will be inspected and confirmed by an authorized service provider who can decide to re pair, refurbish or replace it, and the replaced parts will not be returned. As for the products found to be fault- free during inspection, they will be returned as they are.

DALEN Aladdin Magic Light Non-Warranty Policy

1. Damage caused by improper use, maintenance or storage not in accordance with the product manual;
2. Damage caused by dismantling or repairing by non- authorized service providers of this product;
3. Damage caused by force majeure;
4. The product model or code on the warranty card does not match the actual product;
5. Normal discoloration, wear and consumption during use;
6. The product use failure caused by the consumer’ s own network problems;
7. The returned power supply has obvious hard damage, breakage, broken feet, serious disguise, power line damage, disconnection, bare core, etc. , this kind of power supply is not guaranteed to be replaced.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Customer Support

Brand owner/ Manufacturer：
Jiangsu Dalen Electronic Co. , Ltd. Website： www.dalen-tech.com
Email： sales@dalen-tech.com
Hot line：4006-460-988
After-sale service supported by DALEN

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>