HEARTTH and HOME TA-EXC25 Double Sided Gas Fireplace User Manual

HEARTTH and HOME TA-EXC25 Double Sided Gas Fireplace

Specifications

• Model: TA-EXC25/30/35
• Material: Sheet metal, glass
• Power Source: Electric
• Dimensions: Varies based on model

Product Usage Instructions

Installation Instructions

1. Remove the shipping bracket from the surround.
2. Locate the coiled rocker switch wires and battery backup on the insert.
3. Run both low voltage wires behind the surround and connect them to the rocker switch and USB-C plug.
4. Install the front by engaging four J-hooks with hanging slots and pulling the front forward to verify proper engagement.
5. To install the glass vanity, tuck it between the glass and glass frame.
6. Slide the hood forward until it bottoms out on the front/mesh.
7. Once the surround is attached and hood is properly positioned and secured, slide the appliance backward until tight to the non-co bustible finished wall.

Introduction
The surround is used to fill the space between the insert and the solid fuel firebox opening. The front is placed onto the surround after it is attached to the insert. The surround is required.

Warnings

• Risk of Cuts, Abrasions, or Flying Debris: Wear protective gloves and safety glasses during installation.
• Danger: Hot glass will cause burns. Do not touch glass until cooled. Never allow children to touch glass.
• Risk of Fire: Combustible materials must not overlap or be placed under a surround.

FAQ

• Q: Can combustible materials be used around the appliance?
  A: No, combustible materials must not overlap or be placed under a surround to reduce the risk of fire.

• Q: Is installation of the glass vanity panel necessary?
  A: Yes, to install the glass vanity, tuck it between the glass and glass frame as instructed in Figure 11.

Surround / Front: TA-EXC25/30/35, INFIT-25/30/35 IA-MI25/30/35, FS- MI25/30/35, MFV-EXC25/30/35, FA-EXC25/30/35, HARC-MI25/30/35,CSFI25/30/35, CASFI25/30/35, MFV-TRI35/30/35, FA-TRI25/30/35, TA-TRI25/30/35 Installation Instructions –

Leave this manual with party responsible for use and operation.

CAUTION! Risk of Cuts, Abrasions or Flying Debris. Wear protective gloves and safety glasses during instal-lation. Sheet metal edges are sharp.

DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS UNTIL COOLED.
NEVER ALLOW CHILDREN TO TOUCH GLASS.

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed for the protection of children and other at-risk individuals.

• CAREFULLY SUPERVISE children in same room as fireplace.
• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

• Keep clothing, furniture, draperies and other flammable materials away.
• Do NOT operate with protective barriers open or removed.
• The decorative front must remain closed if children will be present during the operation of the fireplace.
• The decorative front may be made operable per these instructions. This may be done only upon request of a person responsible for the use and operation of the fireplace.
• The decorative front can be returned to the locked position following these instructions.

INTRODUCTION

The surround is used to fill the space between the insert and the solid fuel firebox opening. The front is placed onto the surround after it is attached to the insert. The surround is required.
WARNING! Risk of Fire! Combustible materials MUST NOT overlap or be placed under a surround.

Combustible Materials Specification
Materials made of or surfaced with wood, compressed paper, plant fibers, plastics, or other material that can ig-nite and burn, whether flame proofed or not, or plastered or unplastered shall be considered combustible materials.

SURROUND & FRONT INSTALLATION

1. Remove the shipping bracket from the surround. See Figure 2.

2. Locate the coiled rocker switch wires and battery backup on the insert. The wire assembly is zip-tied to the right side of the appliance outer wrap.

3. Run both low voltage wires behind the surround. Connect the low voltage wires to the rocker switch and USB-C plug.. See Figure 1.
   Note : For alternative rocker switch location using the rocker switch mounting bracket see Figure 2 for PROVIDENT/ JASPER metal inserts and see Figure 3 for all other metal inserts.

4. Attach surround to the insert with four screws (located in appliance manual bag). See Figure 4. When installing a 4-sided surround, install shoulder screws in bottom corners of surround opening. Bend tabs on vanity panel toward the 90° return bend and hang on shoulder screws. See Figures 5 and 6. Note : When being used with 4-sided surround, bend bracket approximately 15°at the hand bend line to avoid contact with vanity panel. See Figure 4.

5. Install the front.
   Locate four hanging slots on the appliance. Engage four J-hooks with hanging slots. Carefully, pull the front forward to verify proper engagement.

6. Slide the hood forward until it bottoms out on the front/mesh. See Figure 9 and 10.
   Note : For Infit front, discard the surround hood.

7. Once the surround is attached and hood is properly positioned and secured, slide the appliance backward until the surround is tight to the non-combustible finished wall. 8. See below chart for glass vanity install details.

11

TA-EXC25/30/35
FA-TRI25/30/35
TA-TRI25/30/35

To install glass vanity, tuck it between the glass and glass frame as shown in Figure 11.

Cleaning Instructions for Fronts/Surounds

Use a microfiber cloth and Windex® Original Glass Cleaner or 03M003 Stove Bright® Glass Cleaner to clean the fronts/surround immediately after installation to remove acids deposited by the installer or technician. Spray the cleaner onto the microfiber cloth and carefully wipe the entire surface. The front/surround should be cleaned in this manner annually by the homeowner to remove fingerprints or other contaminants. Once oxidation of the paint pigment has occurred, cleaning will not restore the original color.

Service Part List

SURROUNDS| DESCRIPTION| PART NUMBER|
---|---|---|---
MI25-3523-(All colors)| | |
MI25-3726-(All colors)| | |
MI25-3928-(All colors)| | |
MI30-4027-(All colors)| | |
MI30-4230-(All colors)| ROCKER SWITCH| |
| SRV2206-299|
MI30-4432-(All colors)|
ROCKER SWITCH MOUNTING| |
BRACKET| |
MI35-4229-(All colors)|
(Optional, See Figure 2)| 2532-299|
MI35-4432-(All colors)| ****

USB-C WIRE ASSEMBLY

| ****

SRV2326-222

|
MI35-4832-(All colors)| | |
MI30-4629CST-BK| | |
MI35-5133CST-BK| |
MI25-5040CS-BK| ****

ROCKER SWITCH

| ****

SRV2206-299

|
|
MI30-5040CS-BK| ROCKER SWITCH MOUNTING BRACKET (OPTIONAL, SEE FIGURE 2)| 2532-299|
MI35-5040CS-BK|
| VANITY PANEL| 2532-204|
CUST-SRND-MI| ****

USB-C WIRE ASSEMBLY

| ****

SRV2326-222

|
FRONTS| DESCRIPTION| PART NUMBER
---|---|---
TA-EXC25-(All colors), TA-TRI25-(All colors)| ****

MESH

| 2531-034
TA-EXC30-(All colors), TA-TRI30-(All colors)| 2532-034
TA-EXC35-(All colors), TA-TRI30-(All colors)| 2533-034
TA-EXC25-(All colors), TA-TRI25-(All colors)| ****

GLASS VANITY PANEL

| 2531-247
TA-EXC30-(All colors), TA-TRI30-(All colors)| 2532-247
TA-EXC35-(All colors), TA-TRI35-(All colors)| 2533-247
IA-MI25-(All colors)| ****

MESH

| 2531-034
IA-MI30-(All colors)| 2532-034
IA-MI25-(All colors)| 2533-034
INFIT-25-BK| ****

MESH

| 2531-029
INFIT-30-BK| 2532-029
INFIT-35-BK| 2533-029
HARC-MI25-(All colors)| ****

MESH

| 2531-034
HARC-MI30-(All colors)| 2532-034
HARC-MI35-(All colors)| 2533-034
MFV-EXC25-(All colors), MFV-TRI25| ****

MESH

| 2531-034
MFV-EXC30-(All colors), MFV-TRI30| 2532-034
MFV-EXC35-(All colors), MFV-TRI35| 2533-034
FS-MI25-(All colors)| ****

MESH

| 2531-034
FS-MI30-(All colors)| 2532-034
FS-MI35-(All colors)| 2533-034
FA-EXC25-BK, FA-TRI25-BK| ****

MESH

| 2531-034
FA-EXC30-BK, FA-TRI30-BK| 2532-034
FA-EXC35-BK, FA-TRI30-BK| 2533-034
FA-EXC25-BK, FA-TRI25-BK| ****

GLASS VANITY PANEL

| 2531-247
FA-EXC30-BK, FA-TRI30-BK| 2532-247
FA-EXC35-BK, FA-TRI35-BK| 2533-247
CSFI25(All colors)| ****

MESH

| 2531-034
CSFI30(All colors)| 2532-034
CSFI35(All colors)| 2533-034
CASFI25(All colors)| ****

MESH

| 2531-034
CASFI30(All colors)| 2532-034
CASFI35(All colors)| 2533-034

Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
www.hearthnhome.com
Please contact your Hearth & Home Technologies dealer with any questions or concerns. For the location of your nearest Hearth & Home Technologies dealer, please visit www.hearthnhome.com.
Hearth & Home Technologies • Insert Surround / Front Installation Instructions • 2532-921 Rev. i • 5/24

References

• Hearth & Home Technologies

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>