HUIZHOU RC36 Bluetooth Voice Remote Control Instructions

HUIZHOU RC36 Bluetooth Voice Remote Control

Specifications

• Model: RC-36
• Operating Frequency: 2440MHz
• Transmission Time: 20 seconds
• Battery Voltage: 2.4V
• Power: Single carrier, maximum power of the chip

Product Usage Instructions

Pairing Mode:

To enter pairing mode:

1. Press and hold the [ ] key and [ ] key on the remote control simultaneously for about 3 seconds.
2. Wait for the indicator to start flashing, indicating pairing mode.
3. Turn on the Host Bluetooth and search for devices.
4. Connect to the RC-28 device name.
5. If pairing is successful, the indicator will stop blinking after a few seconds.
6. If unsuccessful, the indicator will flash 2 times after 30 seconds and exit pairing mode.

Low power alarm

When the battery power is lower than 2.4V, Every time the user presses a key, Press any key, the red light flashes for 3s, and the frequency is 1 Hz

Auto sleep

Without any data interaction, the remote control keeps connected for 1 hour and then enters into the state of sleep disconnection, press any key to wake up the remote control, if still connected, then send the corresponding key Bluetooth code value; If you have entered the Bluetooth connection disconnect state, you will enter the back connect state,After successful connection,Press any key to send the corresponding Bluetooth code value;

Keep the remote control connected with the TV set at 4m for at least 1 hour without disconnection; When there is pairing information and the Bluetooth connection is
disconnected, Press the “power key” and “pairing combination key” to not send the back connection broadcast. Any other key sends the back connection broadcast for 5 seconds, the back connection is successful, and the indicator flashes for 3 times

OTA

When the TV is turned on, the upgrade fi file of the remote controller is detected. If the upgrade fi file exists, the remote controller performs OTA upgrade, and the LED lamp f1 flashes in breathing light Shuo. At this time, the remote controller can’t be used, and any buttons don’t respond. After the upgrade is successful, the LED light stops f1 flashing, and the remote controller can be used normally at this time. If the upgrade fails, it will be detected and upgraded again at the next boot. After OTA fails, the LED light stops f1 flashing, and the remote controller returns to the old version for normal operation.

PID/VID
vendor:0x0B7A. product:0X1488

Battery Low Voltage:

When the battery voltage drops below 2.4V:

• The red light flashes for 3 seconds at a frequency of 1Hz every time a key is pressed.

Remote Control Range:

Maintain a connection between the remote control and the TV set at a distance of 4m for at least 1 hour without disconnection.

Sleep and Wake Up:

If there is no data interaction, the remote control remains connected for 1 hour before entering sleep mode. Press any key to wake up the remote control. If still connected, send the corresponding Bluetooth code value.

Indicator Status:

Infrared Mode:

• Keys do not light up.

Bluetooth Mode:

• Keys do not light up.

Indicator Lights:

Red light flashes for 30 seconds at a frequency of 2Hz in low voltage state.

Indicator status

The red light flashes for 30 seconds at a frequency of 2Hz

Pairing succeeded| The red light stays on for 3 seconds
Pairing failed| The red light goes out
Low voltage state| Key| Press any key and the red light flashes for 3 seconds at a frequency of 1 Hz

FCC Warnning

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmfulinterferenc e to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.

FAQ

Q: What should I do if pairing fails?

A: If pairing fails, the red light will stay on for 3 seconds. Try pairing again following the instructions provided.

Q: How can I exit single carrier mode?

A: Press volume – to exit the single carrier mode.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>