Keychron Lemokey L1 Keyboard Kit User Guide

Lemokey L1 Keyboard Kit User Guide

Fully Assembled Version

Keyboard

1x Fully Assembled Keyboard
Including
1x Aluminum Case
1x PCB
1x PC Plate
1x Sound Absorbing Foam
1x IXPE Foam
1x Bottom Case Acoustic Foam
1x Bottom Case PET Film
16x Gaskets (12 Installed and 4 in the Box)
4 Sets x Stabilizers
1 Set x Keycaps (PBT Double-shot)
1 Set x Switches

Cable

1x Type-C to Type-C Cable
1x Type-A to Type-C Adapter
1x Extension Adapter For Receiver
Receiver
1x Type-A 2.4GHz Receiver

Tools
1x Keycap-Switch Puller
1x Screwdriver
1x Hex Key

Barebone Version

Keyboard Kit
1x Keyboard Kit (Without Keycaps & Switches)
Including
1x Aluminum Case
1x PCB
1x PC Plate
1x Sound Absorbing Foam
1x IXPE Foam
1x Bottom Case Acoustic Foam
1x Bottom Case PET Film
16x Gaskets (12 Installed and 4 in the Box)
4 Sets x Stabilizers

Cable

1x Type-C to Type-C Cable
1x Type-A to Type-C Adapter
1x Extension Adapter For Receiver
Receiver
1x Type-A 2.4GHz Receiver
Tools
1x Keycap-Switch Puller
1x Screwdriver
1x Hex Key

1. Connect 2.4GHz Receiver Note: For the best wireless experience, we recommend using the extension adapter for receiver and putting the 2.4GHz receiver somewhere on your desk close to your keyboard for a low rate of latency and fewer signal interferences.

2. Connect Bluetooth

3. Connect Cable

4. The VIA Key Remapping Software
   Please visit usevia.app to use the online VIA software to remap the keys.
   If the VIA cannot recognize your keyboard, please reach our support to get the instruction.*The online VIA software can only run on the latest version of Chrome, Edge, and Opera browsers yet.
   “VIA only works when the keyboard is connected by wire to the computer.

5. Switch to Mac

6. The Backlight

7. Adjust The Backlight Brightness

8. Adjust The Backlight Speed

9. The Key Rollover
   Press Fn + N to switch N-key rollover / 6-key rollover 6-key rollover: the keyboard can detect up to 6 simultaneous key inputs.
   N-key rollover: the keyboard can detect all key inputs without limit to the number of key presses. *The keyboard turns on the 6-key rollover by default.

10. Warranty
    The keyboard is highly customizable and easy to be rebuilt.
    If anything goes wrong with any of the keyboard components of keyboard during the warranty period, we will only replace the defective parts of the keyboard, not the whole keyboard.

11. Factory Reset Troubleshooting? Don’t know what’s going on with the keyboard?
    1. Download the right firmware and QMK Toolbox from our website.
    2. Unplug the power cable and switch the keyboard to Cable mode.
    3. Remove the space bar keycap to find the reset button on the PCB.
    4. Hold the reset key first, then plug the power cable into the keyboard.
    Release the reset key after 2 seconds, and the keyboard will now enter DFU mode.
    5. Flash the firmware with the QMK Toolbox.
    6. Factory reset the keyboard by pressing Fn + J + Z (for 4 seconds).
    *Step by step guide can be found on our website.

KEY DESCRIPTION

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement in portable exposure condition without restriction.

Keychron, Inc.
Dover, DE 19901, United States
Find us at: https://www.keychron.com
Support@keychron.com
  @keychron
@keychron
@keychronMK
Designed by Keychron
Made in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>