Lenovo neo50t Motherboard Mainboard User Manual

Lenovo neo50t Motherboard Mainboard

Information

Version 1.0
Published April 2024

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference.
2. this device must accept any interference received, including interference that may cause undesired operation.

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/perchlorate”

AUSTRALIA ONLY

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage caused by our goods. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

The terms HDMI™ and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

Motherboard Layout

Front And Rear Panel

Front Panel

Rear Panel

(USB4_1)
5| USB 3.2 Gen1 Type-A Ports (USB_4_5)
---|---
6| 2.5G LAN RJ-45 Port**
7| USB 3.2 Gen1 Type-A Ports (USB_6_7)
8| DC Jack***

• USB4 for RyzenTM 8000G Series Processors; USB 3.2 Gen2 (supports DP Alt mode) for RyzenTM 7000 Series Processors
  ** There are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.

Activity / Link LED| Speed LED|
---|---|---
Status| Description| Status| Description
Off| No Link| Off| 10Mbps connection
Blinking| Data Activity| Orange| 100Mbps/1Gbps connection
On| Link| Green| 2.5Gbps connection

*** Please use a 19V power adapter for the DC jack. This jack accepts dual barrel plugs with an inner diameter of 2.5 mm and an outer diameter of 5.5 mm, where the inner contact is +19 (±10%) DC and the shell is (centre positive).

Please use a 90W adapter for the 35W CPU and a 120W adapter for the 65W CPU.
This motherboard is available with support for either 4-pin ATX 19V power or DC-in power supplies. Please do not use two kinds of power supplies at the same time! Doing so may damage the motherboard components and devices. When you use the DC-in power adapter, please use the onboard SATA power connector to get the power for HDDs.

Introduction

Thank you for purchasing X600D5-P1 motherboard. In this documentation, Chapter 1 and 2 contains the introduction of the motherboard and step-by-step installation guides.

Because the motherboard specifications and the BIOS software might be updated, the content of this documentation will be subject to change without notice.

Package Contents

• X600D5-P1 Motherboard
• 1 x Quick Installation Guide
• 1 x SATA Data with Power Cable (Optional)
• 2 x Screws for M.2 Sockets (Optional)
• 1 x Screw for WiFi Module (Optional)

Specifications

Platform| •    6.7-in x 6.8-in, 17.0 cm x 17.2 cm

•    Solid Capacitor design

---|---
CPU| •    Supports AMD Socket AM5 RyzenTM 8000 and 7000 Series Processors

Supports CPU up to 65W 4+1+1 Power Phase design

Chipset| •    AMD X600
Memory| •    Dual Channel DDR5 Memory Technology

•    2 x DDR5 SO-DIMM Slots

•    Supports DDR5 non-ECC, un-buffered memory up to 6400+(OC)*

•    Max. capacity of system memory: 96GB

• Please refer to Memory Support List on ASRock’s website for more information. (http://www.asrock.com/)

Expansion Slot| •    1 x M.2 Socket (Key E), supports type 2230 WiFi/BT module
Graphics| •    Integrated AMD RDNATM graphics (Actual support may vary by CPU)

•    Four graphics output options: 1x HDMI, 2 x DisplayPort 1.4, 1 x Type-C

• Supports up to 4 displays simultaneously

•    1 x HDMI 2.1 TMDS 8G Compatible, supports HDR, HDCP

2.3 and max. resolution up to 4K 120Hz

•    2 x DisplayPort 1.4 with DSC (compressed), supports HDCP

2.3 and max. resolution up to 4K 120Hz

•    1 x Type-C with USB4 for RyzenTM 8000G Series Processors; with DP Alt mode for RyzenTM 7000 Series Processors

Audio| •    Realtek ALC269 Audio Codec

•    1 x MIC IN

•    1 x Headset/Headphone

LAN| •    2.5 Gigabit LAN 10/100/1000/2500 Mb/s

•    Dragon RTL8125BG

•    Supports Dragon 2.5G LAN Software

– Smart Auto Adjust Bandwidth Control

– Visual User Friendly UI

– Visual Network Usage Statistics

– Optimized Default Setting for Game, Browser, and Streaming Modes

– User Customized Priority Control

---|---
Front Panel I/O| •    1 x Power Button

•    1 x Headphone/Headset Jack

•    1 x USB 3.2 Gen1 Type-A Port

•    1 x USB 3.2 Gen1 Type-C Port

•    2 x USB 2.0 Ports

•    1 x Microphone Input Jack

Rear Panel I/O| •    1 x DC Jack (Compatible with the 19V power adapter)*

• Please use 120W power adapter for 65W CPU and 90W power adapter for 35W CPU.

•    1 x HDMI Port

•    2 x DisplayPort*

• (1 x DP co-lay D-SUB)

•    4 x USB 3.2 Gen1 Type-A Ports

•    1 x USB4 Type-C Port (40 Gb/s)*

•    1 x RJ-45 LAN Port

• USB4 for RyzenTM 8000G Series Processors; USB 3.2 Gen2 (supports DP Alt mode) for RyzenTM 7000 Series Processors

Storage| CPU:

•    1 x Hyper M.2 Socket (M2_1, Key M), supports type 2280 PCIe Gen4x4 (64 Gb/s) mode*

•    1 x Hyper M.2 Socket (M2_2, Key M), supports type 2280 PCIe Gen4x4 (64 Gb/s) mode*

ASMedia ASM1061:

•    1x SATA3 6.0 Gb/s Connector

• Supports NVMe SSD as boot disks

•    1 x COM Port Header

•    1 x Chassis Intrusion Header

•    1 x CPU Fan Connector (4-pin)

• The CPU Fan Connector supports the CPU fan of maximum 1A (12W) fan power.

•    1 x Chassis Fan Connector (4-pin) (Smart Fan Speed Control)

•    1 x Mono-Out Header

BIOS

Feature

| •    AMI UEFI Legal BIOS with GUI support
Hardware Monitor| •    Fan Tachometer: CPU, Chassis Fans

•    Quiet Fan (Auto adjust chassis fan speed by CPU temperature): CPU, Chassis Fans

•    Fan Multi-Speed Control: CPU, Chassis Fans

•    CASE OPEN detection

•    Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore

OS| •    Microsoft® Windows® 10 64-bit
Certifications| •    FCC, CE

•    ErP/EuP ready (ErP/EuP ready power supply is required)

Warning: Please realize that there is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using third-party overclocking tools. Overclocking may affect your system’s stability, or even cause damage to the components and devices of your system. It should be done at your own risk and expense. We are not responsible for possible damage caused by overclocking.

Installation

This is a Proprietary form factor motherboard. Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard components or change any motherboard settings.

• Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so may cause physical injuries to you and damages to motherboard components.
• In order to avoid damage from static electricity to the motherboard’s components, NEVER place your motherboard directly on a carpet. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle the components.
• Hold components by the edges and do not touch the ICs.
• Whenever you uninstall any components, place them on a grounded anti-static pad or in the bag that comes with the components.
• When placing screws to secure the motherboard to the chassis, please do not overtighten the screws! Doing so may damage the motherboard.

Installing the CPU

1. Before you insert the 1718-Pin CPU into the socket, please check if the PnP cap is on the socket, if the CPU surface is unclean, or if there are any bent pins in the socket. Do not force to insert the CPU into the socket if above situation is found. Otherwise, the CPU will be seriously damaged.
2. Unplug all power cables before installing the CPU.

Tutorial Video

Warning

• Turn your CPU to the correct orientation before opening the CPU socket cover.

Warning: Carefully place the CPU in as flat as possible. Do not drop it.

Warning: Make sure the CPU is aligned with the socket before locking it into place.

Warning: Make sure the black cover plate is always in place until it pops off when closing the socket lever.

Please save the cover if the processor is removed. The cover must be placed if you wish to return the motherboard for after service.

Installing the CPU Cooler

After you install the CPU into this motherboard, it is necessary to install a larger heatsink and cooling fan to dissipate heat. You also need to spray thermal grease between the CPU and the heatsink to improve heat dissipation. Make sure that the CPU and the heatsink are securely fastened and in good contact with each other.

Tip: Please turn off the power or remove the power cord before changing a CPU or heatsink.

Installing Memory Modules (SO-DIMM)

This motherboard provides two 260-pin DDR5 (Double Data Rate 5) SO-DIMM slots, and supports Dual Channel Memory Technology.

1. For dual channel configuration, you always need to install identical (the same brand, speed, size and chip-type) DDR5 SO-DIMM pairs.
2. It is unable to activate Dual Channel Memory Technology with only one memory module installed.
3. It is not allowed to install a DDR, DDR2 , DDR3 or DDR4 memory module into a DDR5 slot; otherwise, this motherboard and SO-DIMM may be damaged.
4. The SO-DIMM only fits in one correct orientation. It will cause permanent damage to the motherboard and the SO-DIMM if you force the SO-DIMM into the slot at incorrect orientation.

Recommended Memory Configuration

The first boot may take some time.
Please be patient and refer to the following table for booting time.
*It may vary by different setups.

1. Carefully insert the SO-DIMM memory modules into the slot at a 30-degree angle.
2. Push down until the modules snap into place.

Jumpers Setup

The illustration shows how jumpers are setup. When the jumper cap is placed on the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is “Open”.

CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes system setup information such as system password, date, time, and system setup parameters. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord, then use a jumper cap to short the pins on CLRCMOS1 for 3 seconds. Please remember to remove the jumper cap after clearing the CMOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action.

If you clear the CMOS, the case open may be detected. Please adjust the BIOS option “Clear Status” to clear the record of previous chassis intrusion status.

Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage to the motherboard.

M.2 WiFi/BT Module Installation Guide

The M.2 is a small size and versatile card edge connector that aims to replace mPCIe and mSATA. The M.2 Socket (Key E) supports type 2230 WiFi/BT module.

Installing the WiFi/BT module

• Step 1

  • Prepare a type 2230 WiFi/BT module and the screw.

• Step 2

  • Find the nut location to be used.

• Step 3

• • Gently insert the WiFi/BT module into the M.2 slot. Please be aware that the module only fits in one orientation.

• Step 4

  • Tighten the screw with a screwdriver to secure the module into place.
  • Please do not overtighten the screw as this might damage the module.

M.2 SSD Module Installation Guide

The M.2 is a small size and versatile card edge connector that aims to replace mPCIe and mSATA. The Hyper M.2 Sockets (M2_1 and M2_2, Key M) support type 2280 PCIe Gen4x4 (64 Gb/s) mode.

Installing the M.2 SSD Module

• Step 1
  • Prepare a M.2 SSD Module and the screw.
• Step 2
  • Gently insert the M.2 SSD module into the M.2 slot. Please be aware that the M.2 SSD module only fits in one orientation.
• Step 3
  • Tighten the screw with a screwdriver to secure the module into place. Please do not overtighten the screw as this might damage the module.

M.2 SSD Module Support List

For the latest updates of M.2 SSD module support list, please visit our website for details.

DECLARATION OF CONFORMITY

DECLARATION OF CONFORMITY

EU Declaration of Conformity

EU Declaration of Conformity

Documents / Resources

| Lenovo neo50t Motherboard Mainboard [pdf] User Manual
neo50t Motherboard Mainboard, Motherboard Mainboard, Mainboard
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>