COMPRESSOR Silver Spk Empress Effects Bass User Manual

COMPRESSOR
BassBass
USER MANUAL

Further Information

On our website (www.empresseffects.com) you will find lots of further information and details on the following points:
Download
This manual is also available as a PDF file for you to download.
Keyword Search
Use the search function in the electronic version of this manual to find your topics of inteterest quickly.
Customer Support
If you have any problems with the device our Customer Support team will gladly assist you.

Symbols and Signal Words

dangerous situation that will result in death or serious injury if it is not avoided
CAUTION!| This combination of symbol and signal word indicates a possible dangerous situation that can result in minor injury if it is not avoided.
NOTICE!| This co mbination of symbol and signal word indicates apossible dangerous situation that can result in material and environmental damage if it is not avoided.
Warning Signs| Type of Danger
---|---
| General warning sign
| Electricity Hazard
| Hot Surface
| Sudden Loud Noises

Intended Use

This pedal is designed for enhancing guitar tones in live performances and studio recordings.
Use as outlined in the user manual.
The manufacturer is not liable for damages resulting from improper use or use under non-recommended conditions.

Safety

| DANGER! Danger for children
Dispose of plastic bags and packaging properly to keep them out of reach of babies and young children to prevent
choking hazards. Ensure children don’t detach small parts like knobs to avoid choking. Never leave children
unattended with electrical devices.
---|---
| DANGER! Electrical shock
Risk of electrical shock from exposed wires or damaged components. Inspect pedals for damage before use. If
damaged, stop use and seek professional repair.
| DANGER! Power Supply Issues
Use the right voltage and current for your pedal’s power supply to prevent damage and safety risks. Check the
power supply’s condition, and for multiple pedals, opt for a dedicated supply to avoid overloading by daisy-chaining.
| CAUTION! Overheating
Avoid overheating. Do not stack pedals or place in confined spaces. If a pedal overheats, stop using and let it cool.
| CAUTION! Tripping Hazard / Pedal Placement
Prevent tripping: Secure cables and place pedals firmly to avoid slips and falls.
| CAUTION! Volume Spikes
Beware of volume spikes and unexpected sounds when adjusting pedal settings
| NOTICE! Allergies or Sensitivities
Allergy Alert: Some pedal materials, like adhesives and coatings, may cause reactions. Stop use and seek medical advice if needed.
| NOTICE! Fire Hazard
Keep away from direct heat and open flames.

Introduction

When we released our original Compressor back in  2011, it quickly became a favourite among guitar and bass players alike who were searching for something more than the typical oversimplified controls found on most compressor pedals. Although our original
Compressor sounded great on bass (and still does!) we set out to do even better.
On top of the full range of features and controls normally only seen in high end studio equipment, such as input and gain reduction metering, independent attack and release controls, a mix knob for parallel compression, and an external sidechain insert, we’ve now added a fully variable sidechain high pass filter, and a two position ‘tone + colour’ circuit which adds gentle tone sculpting and harmonic distortion, giving your bass some delicious character.
We hope the Bass Compressor becomes a favourite of yours as well, and sincerely thank you for choosing Empress Effects.
– Steve Bragg

The Basics of Compression

Compression can add consistency and sustain to your playing or it can be used to add note definition and other effects. It essentially narrows the difference between high and low audio levels by reducing the gain of any signal over the threshold.

The ratio determines how much gain reduction will be applied to the signal once it crosses over the threshold. At a 4:1 ratio, for every 4dB of input signal above the threshold, there will be 1dB of output signal. A 10:1 ratio would output 1dB for every 10dB of input signal, etc.
Attack controls how quickly the gain reduction will begin after a signal has crossed over the threshold. Release controls how long it takes for the Compressor’s gain to return to its initial level after the signal drops below the threshold.

Sidechain

The sidechain is the Compressor’s level detection circuitry. Based on the signal sent to it, it will determine how much gain reduction is applied. Typically that signal is a copy of the input signal, taken from some point in the audio path. In our case it’s taken after the gain reduction has occurred, which is known as ‘feedback’ style compression. It can be very useful to alter the sidechain signal in order to

tailor how the compressor reacts.
Sidechain High Pass Filter
The SC HP (high pass filter) knob can be used to avoid triggering the compression with high energy low frequency notes, which helps avoid overcompressing and keeps the low frequencies sounding full while still controlling errant high notes that pop out.
Sidechain connector jack
The sidechain connector jack on the back of the pedal allows you to alter the sidechain signal by inserting an external device, such as an EQ. You can also have an external audio source trigger the compression by sending audio in through the ring of the sidechain jack.
The sidechain connector accepts a 1/8” TRS plug:
Tip = send, Ring = return, Sleeve = ground.

Parallel Compression

The mix knob on the Bass Compressor allows for parallel compression. Parallel compression is achieved by blending a compressed audio signal with the uncompressed version of itself. It opens up a ton of possibilities. A great use of parallel compression is to really squash the compressed signal (so it sounds way too over compressed), then use the mix knob to blend in some of the uncompressed signal. The result is very natural sounding, but feels a lot more exciting, with more sustain and retaining a good attack. Try
experimenting with it!

Controls at a Glance

• The colour circuit can be bypassed in either or both tone switch positions via internal dipswitches. Set the corresponding dipswitch to off if you prefer just the tone eq without the colour circuit.
  ** Empress Effects fully endorses bass solos.

Setting the Bypass State on Startup

To change whether the Compressor starts up in the engaged or bypassed state, hold down the stompswitch while powering on the Compressor. The first red gain reduction led will flash to let you know you are in the advanced configuration mode. Press the stompswitch to toggle between states:

gain reduction led 1 = bypassed at startup
gain reduction led 2 = engaged at startup

When finished, press and hold the stompswitch for 2 seconds to confirm and save your selection, and exit advanced configuration.

Quickstart

Added Control: Here’s a good starting point for adding consistency and sustain to your playing while retaining dynamics. Adjust the input level so the gain reduction meter shows 8dB of gain reduction when playing your loudest.

Smooth & Warm:
Smooth, subtle compression that gives transparent dynamic control with a gentle mid- scoop and some warmharmonic distortion.

Slappa Da Bass: The heavy compression ratio will keep your pops under control, while the slow attack and quick release will enhance the percussive qualities of a finely slapped bass.

Level & Grind: This limiter will help keep your levels rock solid, while the mid-boost and distortion gives your bass some added presence and character.

Powering the Bass Compressor

Go to www.empresseffects.com/power for a full list of compatible power supplies.
Please note: The Empress Bass Compressor requires at least 100mA of current to function properly. Any power supply rated at 9V DC, supplying negative tip polarity and at least 100mA of current should work.

Regulatory Compliance Information

FCC (USA)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Responsible Party in the USA
Americas Compliance Consulting LLC dba iCertifi
1001 SW Disk Drive, Ste 250
Bend, Oregon 97702 USA
FCC_sDoC@icertifi.com
icertifi.com

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

ICES-003 (Canada)
CAN ICES-003(B) / NMB-003(B)
CE (European Union)
This declaration of conformity is issued under the sole responsibility of Empress Effects Inc- 105-62 Steacie Dr, Kanata Ontario K2K 2A9. The device identified on the front page of this manual is in conformity with the requirements of the European Union’s Electromagnetic Compatibility Directive 2014/30/EU, in accordance with the following harmonized standards:

• EN 55032:2015/A11:2020 – Electromagnetic compatibility of multimedia equipment – Emission Requirements
• EN 61000-3-2:2014 – Electromagnetic compatibility (EMC) – Part 3-2: Limits – Limits for harmonic current emissions (equipment input current ≤ 16 A per phase)
• EN 61000-3-3:2013 – Electromagnetic compatibility (EMC) – Part 3-3: Limits – Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current ≤ 16 A per phase and not subject to conditional connection
• EN 55035:2017/A11:2020 – Electromagnetic compatibility of multimedia equipment – Immunity Requirements

Name: Colin King
Title: Design Engineer
Company: Empress Effects Inc
Date: August 19, 2023
Location: 105-62 Steacie Dr, Kanata Ontario K2K 2A9

WEEE (2012/19/EU)
This product must not be disposed of with regular household waste. In compliance with WEEE regulations, please take this product to a designated collection facility or return to the supplier for proper recycling. Comply with local laws and regulations for disposal. Contact your local authority or support@empresseffects.com for specific information.
Disposal of the packaging material
For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly disposed of. Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.

Specifications

Manual v05

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>