LENZ J1772 Electric Vehicle Charger Holster User Manual
- June 26, 2024
- Lenz
Table of Contents
LENZ J1772 Electric Vehicle Charger Holster
Safety Information
Before starting the installation, thoroughly read and understand the entire installation manual provided with the product. Pay close attention to the instructions and guidelines provided and follow them step-by-step. Take note of any specific guidelines regarding screw sizes, recommended torque, wall compatibility, or any other relevant information outlined in the manual.
- Secure Mounting: Before proceeding with the installation, it is crucial to verify that the chosen wall or surface is both sturdy and capable of supporting the weight of the product, as well as the J1772 handle and cable. This will ensure a safe and reliable installation.
- Tools and Equipment: Use proper tools, such as a drill and screwdriver, to securely attach the mount to the wall. Ensure the tools are in good condition and suitable for the task.
- Stability Check: After installation, gently test the stability and sturdiness of the mounted product. Make any necessary adjustments or retighten screws if needed.
- ADA Compliance: In compliance with the Americans with Disabilities Act (ADA), it is important to consider accessibility requirements during the installation process. Ensure that the product’s placement and mounting do not impede or obstruct pathways, particularly in areas designated for accessibility. Take into account any applicable ADA guidelines and regulations to ensure a universally accessible installation.
Specifications
- Operating Temperature: -22°F to +122°F (-30°C to +50°C)
- Connector Port: SAE J1772
- Weight: 1.12 lbs
Product Overview
- A. Main Housing (”Holster”): Designed to securely hold and support your J1772 handle and cable.
- B. Installation Bracket: A bracket to secure and attach Mount Housing.
- C. Screws: Two (2) screws for attaching the Installation Bracket to the wall.
- D. Drywall Anchors: Two (2) expandable drywall anchors for when attaching. Installation Bracket to studs is not possible.
Preparation
-
Electric Vehicle (EV) Charging Cable and Handle: This product is designed to
securely hold and support your J1772 EV charging cable and handle. Please make sure you have the appropriate cable and handle that are compatible with your EV charging system. Mounting Location: Select a suitable location for installing the product. Ensure the chosen wall or surface is sturdy and capable of supporting the weight of the product, as well as the J1772 handle and cable. -
Power Tools: You will need a drill with the appropriate drill bit for the mounting screws and drywall anchors. This will allow you to securely attach the installation bracket to the wall.
-
Screwdriver: Have a screwdriver available to tighten the screws during the installation process.
-
Level : To ensure a level installation, have a bubble or laser level on hand to check the alignment of the installation bracket.
-
Pencil or Marker : It is helpful to have a pencil or marker to mark the mounting hole locations on the wall.
-
Safety Equipment: Wear appropriate personal protective equipment (PPE) during the installation, such as safety gloves and goggles, to protect yourself from potential hazards.
How to Install
Step 1:
- Mark and Drill Starter Holes: Mark the desired location and drill holes for mounting plate (Part A).
- With the appropriate drill bit, carefully drill starter holes at the marked locations.
Step 2:
- Secure Installation Bracket into place: Position the Installation Bracket over the drilled starter holes. Utilize provided screws to secure the Installation Bracket to the wall and stud.
- If mounting on drywall or a similar surface, use the included drywall anchors for added stability. Use a screwdriver to securely tighten the screws, ensuring the bracket is firmly attached to the wall (see Figure A).
Step 3:
- Attach the Main Housing Unit (“Holster”): Slide the Main Housing Unit onto the Installation Bracket (see Figure B).
- Confirm the Main Housing Unit is securely engaged with the Installation Bracket before use
- If you plan to secure Holster to wooden stud behind the drywall, please utilize appropriate stud screw, which are normally 1 5/8 inches long (NOT INCLUDED).
FAQ
Q: Can this product be used with any J1772 EV charging cable and handle?
A : Yes, the product is designed to accommodate most J1772 EV charging cables and handles available on the market. However, it is recommended to check the compatibility of your specific cable and handle with the product specifications to ensure a proper fit.
Q: Can I install this product outdoors?
A: The product is primarily designed for indoor installations. If you intend to install it outdoors, ensure that it is protected from direct exposure to rain, snow, and excessive sunlight. Additionally, consider using weatherproofing measures or enclosures to safeguard the product against environmental elements.
Q: Can I adjust the position of the mount bracket after installation?
A : Once the mount bracket is securely installed, it is recommended to avoid adjusting its position. However, if necessary, carefully remove the screws, make the desired adjustments, and then reattach the bracket to ensure a stable and secure fit.
Usage Guideline
Ensure that the J1772 handle and cable are inserted and removed from the mount
housing with care. Avoid applying excessive force or bending the cable during
the process. This will help maintain the longevity and functionality of both
the EV charging cable and the product.
Warranty & Support
Register your product today to extend your warranty protection for an additional 6 months, and stay informed on the latest and, sometimes, critical updates. And get special offers! Scan QR code to go to our registration page.
Disclaimer
LENZ is not affiliated with Tesla Inc. The term ‘Tesla’ is a trademark of
Tesla Inc., used here only for compatibility description purposes.
Headquarters
17 Hammond, Unit 401
Irvine, California 92618
USA
For additional information visit our website:
www.lenzcharging.com
Contact us at info@lenzcharging.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>