VK02 Viking Nebula Laser User Manual
- June 26, 2024
- VIKING
Table of Contents
VK02 Viking Nebula Laser
Specifications:
- Voltage: AC100V-250V, 50HZ/60HZ auto-sensing
- Rated Power : 20w
- Laser :
- Red laser, 700mw, wavelength 638nm
- Green laser, 800mw, wavelength 520nm
- Blue laser, 1500mw, wavelength 450nm
- Laser lifespan : >10000 hours
- Waterproof Level : IP65
- Mains Connector : Truecon
- DMX Control Channel: 7 channels on 3 pin IP65 Data lead to XLR
- Size: 129(L)252(W)106(H)mm
- Weight : 2.4Kg
Product Usage Instructions
Safety Instructions:
- Avoid direct eye exposure to the Laser Beam.
- Avoid pointing at pedestrians, vehicles, or aircraft.
- Avoid projecting near airports.
- Do not turn the unit on and off frequently.
- Clean external lenses periodically with a cleaning tissue.
- Do not attempt to open the unit as there are no user serviceable parts inside.
Function & Setting:
- Auto: Auto cycles the built-in programs without external control.
- DMX Control: Accepts DMX512 signals to control laser beam, ON/OFF, running direction, speed, and twinkle speed.
DMX Control Parameter Chart:
-
* Refer to the chart for different functions and DMX values.
Menu Operation Instruction:
- Use LED Display to monitor and adjust settings for Red and Green lasers.
FAQ:
- Q: How often should I clean the external lenses?
- A: It is recommended to clean the external lenses periodically with a cleaning tissue to optimize light output.
- Q: Can the laser beam cause eye injury?
- A: Yes, avoid direct eye exposure to the Laser Beam as it can potentially cause instant eye injury or blindness.
Notice:
- Avoid direct eye exposure to the Laser Beam. Never intentionally expose your eye or others to a direct laser beam. It an potentially cause instant eye injury or blindness if a laser beam strikes directly to the eyes.
- Don’t point onto any oncoming pedestrians, vehicles or traffic routes from land, sea or air.
- Don’t project at or within the flight path of the aircraft. If your intended surface is within 10 nautical miles of an airport, lower the angle of light so that no lasers point into the sky.
- Don’t turn the unit on and off frequently.
- Use a cleaning tissue to remove the dust absorbed on the external lenses periodically to optimise light output.
- There are no user serviceable parts inside the unit. It must not be opened under any circumstances.
Features:
- 2W high brightness 7 colour aurora effect of laser light. High brightness dreamlike aurora sky starfield effect makes the environment more attractive and romantic. It can be set in single colour or multicolour automatic display mode which can also be controlled by DMX.
- IP65 waterproof housing which is fit for outdoor permanent installation.
- Applicable for stage effect, outdoor bright projects, scenic areas, theme parks, parties or theatre use where an aurora can be projected onto the ceiling or ground. The effect is also enhanced by the use of haze or smoke in the atmosphere.
Technical Specification
- Voltage: AC100V-250V, 50HZ/60HZ auto-sensing
- Rated Power: 20w
- Laser:
- Red laser, 700mw, wavelength 638nm
- Green laser, 800mw, wavelength 520nm
- Blue laser, 1500mw, wavelength 450nm
- Laser lifespan >10000 hours
- Waterproof Level : IP65
- Mains Connector: Truecon
- Work Environment: outdoor and indoor, -35 ° C ~40 ° C
- Scanner : Precise step motor with 60-degree projection angle
- Working Modes: DMX, Manual, White Auto Mode, RGB Auto Mode, Master/Slave Mode
- Technical Specification continued:
- DMX Control Channel: 7 channels on 3 pin IP65 Data lead to XLR – please ensure you have requested this when booking as it cannot be used on DMX without the adaptor cable
- Size : 129(L)252(W)106(H)m
- Weight: 2.4Kg
Front Panel Picture
Rear Panel Picture
Lighting Installation Method
Function & Setting
Auto
Auto cycles the built-in programs without being controlled externally.
DMX Control
The system accepts DMX512 signals from a lighting desk to control the following parameters: the laser beam, ON /OFF, running direction, running speed and twinkle speed etc.
DMX Control Parameter Chart
During DMX mode, use the Up/Down key to change the DMX address, and Enter key to save the parameter. The address will be shown on the monitor as the value from A001 to A511 One unit has 7 channels, so each unit must be assigned in a 7 channel block at least.
DMX Control Parameter Chart
Menu Operation Instruction
After every resetting and save, the new mode information (mode/ DMX address,
speed etc.) will be saved into the CPU and also will be shown on the LED
monitor. Mode/MENU key, to choose the operating mode of the laser.
The Up and Down keys are used to change the parameter or DMX address
confirmation, to confirm press the ENTER key to store the present mode for the
next operation.
DMX Operation (DMX mode)
The mode allows a single unit to react to the beat of the music in the master mode.
-
Install the units in a suitable position.
-
Use a standard XLR microphone cable to chain your units together via the XLR connector on the rear of the units.
For longer cable runs we suggest a terminator at the last fixture. -
Turn on the unit power, the unit begins reset, then the unit begins working.
-
Set Function to DMX mode DMX address of the unit.
-
Use DMX console to control your units.
Notes:
- DMX console can’t be used in Master-Slave operation (manual mode or auto mode).
- There should be only one master unit in the Master-Slave operation.
Master/Slave Operation
This mode will allow you to link up to many units together without a controller.
-
Install the units in a suitable position.
-
Use a standard XLR microphone cable to chain your units together via the XLR connector on the rear of the units.
For longer cable runs we suggest a terminator at the last fixture. -
Turn on the all the power to the units, the units begins reset, then the unit begins working.
-
Choose a unit to function as Master mode, set manual mode or auto mode. The others must be set to Slave mode.
The slave units will react the same as the master unit.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>