Bluedio S6 Wireless TWS Earphone User Manual

Bluedio S6 Wireless TWS Earphone

OVERVIEW

Operation instructions: 1. Long press the headset touch button for 5S, or put the headset into the charging compartment to charge off, Then take out the earphones, turn on the earphones, and the LED is always on, indicating that the earphones The phone has entered the pairing state, the left and right earphones will automatically connect, when the earphone The LED turns to blink, indicating that the left and right earphones are connected successfully. 2. Turn on the bluetooth of the mobile phone, “S6” will appear in the mobile phone pairing list, click to connect Can be connected to a Bluetooth headset.

Touch button control

1. Click to control play/pause answer/hang-up call
2. Double-click the right ear to increase the volume, triple-click to switch to the next song
3. Double-click the left ear to decrease the volume, and triple-click to switch to the previous song
4. Summon the voice assistant, press and hold for 1S, let go after hearing the prompt, click to exit Voice assistant mode
5. In the case of an incoming call, long press 2S to reject the call
6. Last redial 4 hits
7. Clear the pairing information: the headset should be disconnected from the mobile phone, the headset LED always When it’ son or flashing, three-click the touch button to clear the left and right earphones Pairing information. After clearing the pairing information, the headset needs to be reconnected (refer to Point 1 of the instructions for use)

Single ear mode

1. Turn on any earphones separately and connect it to your mobile phone
2. During the normal use of both ears, put the earphones you don’t want to use into the charging compartment, The other headset will remain connected to the phone. (It is recommended to use the second method Very simple and fast)

Charging mode

1. To charge the headset, put the headset into the charging compartment, the charging compartment will display the remaining battery Amount (0-100%), and charge the left and right earphones at the same time, the charging compartment will be Display the charging status of the left and right earphones. When all the displays are off, it means that the earphones have been After being fully charged.
2. Charging in the charging compartment: in the process of charging the charging compartment, such as the digital display: 100%, which means the charging compartment is full Technical specifications Bluetooth version: V5.0 Bluetooth frequency range: 2402MHz-2480MHz Support protocol: HFP 1.7, HSP 1.2, AVRCP 1.6, SPP 1.2 and PBAP 1.0 Horn diameter: 13mm Use distance: barrier-free 10m Talk time: 6-7H (full battery, moderate volume) Music duration: 6-7H (full battery, moderate volume) Battery type: 3.7V, 255mAh polymer lithium battery

Charging compartment specifications Input voltage:

5V 1A Battery type: 3.7V, 2300mAh polymer lithium battery
Charging time: 2-3H lcontact us www.bluedio.com 020-36450093 aftersales@bluedio.com

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.
   Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
   Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>