AMC iLive 2×2 Wireless Microphone System User Manual

AMC iLive 2×2 Wireless Microphone System

Product Information

Specifications
General specifications:

• Dual wireless receivers
• 32 selectable channels
• Automatic channel targeting
• Can be combined with handheld or body pack transmitter
• Variety of microphone selection available for use with body pack
• Outputs: Jack/Jack cable included

Product Usage Instructions

Before You Start
The iLive 2×2 Wireless Microphone System features dual wireless receivers with 32 selectable channels and automatic channel targeting. The wireless microphones sets can be combined with handheld or body pack transmitter with a variety of microphone selections to use with the body pack.

Operation
Front Panel
First Receiver:

1. SET button
2. Navigation buttons
3. SYNC button
4. LCD display
5. IR transmitter

Second Receiver:

6. LCD display
7. SYNC button
8. Navigation buttons
9. SET button
10. Power switch

Rear Panel

1. Antenna A connector
2. XLR audio output from the second receiver
3. XLR audio output from the first receiver
4. Mixed audio output
5. Main power connector
6. Antenna B connector

Frequently Asked Questions (FAQ)

1. Q: Can the iLive 2×2 Wireless Microphone System be used with other microphone brands?
   A: The system can be combined with a variety of microphone selections to use with the body pack, but compatibility with other brands may vary. It is recommended to check the specifications before use.

2. Q: How many channels are available for selection in the system?
   A: The system features 32 selectable channels for flexible use and interference avoidance.

Safety instructions

When using this electronic device, basic precautions should always be taken, including the following:

1. Read all instructions before using the product.
2. Do not use this product near water (e.g., near a bathtub, washbowl, kitchen sink, in a wet basement or near a swimming pool etc).
3. Use this device when you are sure that paging microphone has a stable base and it is fixed securely.
4. This product, in combination with loudspeakers and amplifier may be capable of producing sound levels that could cause permanent hearing loss. Do not operate for a long period of time at a high volume level or at a level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should consult with otorhinolaryngologists.
5. The product should be located away from heat sources such as radiators, heat vents, or other devices that produce heat.
6. The product should be connected to a power supply that is described in the operating instructions or are marked on the product.
7. The power supply should be undamaged and never share an outlet or extension cord with other devices. Never leave device plugged into the outlet when it is not being used for a long period of time.
8. Care should be taken that objects do not fall into liquids and liquids would not be spilled on the device.
9. The product should be serviced by qualified service personnel if:
   • The power supply or the plug has been damaged.
   • Objects have fallen into or liquid has been spilled on the product.
   • The product has been exposed to rain.
   • The product has been dropped or the enclosure damaged.
10. There are some areas with high voltage inside, to reduce the risk of electric shock do not remove cover of the microphone receiver or power supply. The cover should be removed by the qualified personnel only.

CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
To reduce the risk of electric shock, do not remove screws.
No user-serviceable parts inside. Refer servicing to qualified service personnel. To reduce the risk of fire, electric shock or product damage, do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

Before you start
ILive 2×2 – dual wireless receivers with 32 selectable channels and automatic channel targeting. Wireless microphones sets can be combined with handheld or body pack transmitter with variety of microphone selection to use with body pack.

FEATURES

• 2 x 32 selectable channels
• Automatic channel targeting ACT synchronization
• High brightness LCD display
• RF, AF level meter
• Digital volume and squelch control for each receiver
• Lock menu function
• Balanced XLR connector and unbalanced 6,3mm TS jack connector outputs. Jack/Jack cable included

Operation

Front Panel

First receiver

1. SET button

2. Navigation buttons

3. SYNC button

4. LCD display

5. IR transmitter
   Second receiver

6. LCD display

7. SYNC button

8. Navigation buttons

9. SET button

10. Power switch

Rear Panel

1. Antenna A connector
2. XLR audio output from second receiver
3. . XLR audio output from first receiver
4. Mixed audio output
5. Main power connector
6. Antenna B connector

Handheld microphone

1. LCD display
2. IR receiver
3. Power button
4. RF power selector
5. Battery holder
6. Battery cover

Body pack

1. Antenna
2. LCD display
3. IR receiver
4. Battery cover lock
5. Battery holder
6. Battery cover
7. Power button
8. Microphone connector

Receiver operation

SYNC BUTTON
Press this button to transmit data from receiver to transmitter in order to synchronize microphone or body pack transmitter and receiver.

NAVIGATION BUTTONS
These buttons are designed to navigate receivers menu and adjust settings.

SET BUTTON
Short press of this button shows number of current channel for two seconds on LCD screen if channel frequency are displayed for default and otherwise, shows the channel frequency if channel number are set for display default. Long press brings menu on the screen, in order to enter the submenu press SET button one more time. Use navigation buttons to navigate menu or adjust settings.

LCD DISPLAY
Displays the current settings, menu and other information, like RF level, AF level, volume, frequency or channel, lock status, mute status and which antenna A or B is active at the moment.

IR TRANSMITER
IR transmitter allows synchronize microphone or body pack and receiver by establishing handheld microphone or body pack radio frequency to the same as the receiver.

POWER SWITCH
Press power switch for 3 seconds to turn on/off the power.

ANTENNA CONNECTOR
This connector designed to connect antenna to the receiver.

XLR AUDIO OUTPUT
Balanced XLR audio output.

MIXED AUDIO OUTPUT
Unbalanced audio output, 6.3mm TS jack connector. Audio signal in this output is mixed from both receivers.

MAIN POWER CONNECTOR
Connector for DC 12 V – 16 V 1.25A power supply.

Handheld microphone operation

LCD DISPLAY
Displays the current frequency, channel and transmitter’s battery level.

IR RECEIVER
IR receiver allows synchronizing microphone and receiver by establishing hand- held microphone radio frequency to the same as set in receiver.

POWER BUTTON
Press power button for 3 seconds to turn on/off the power.

BATTERY HOLDER
Battery holder for two pieces of AA sizes alkaline batteries. Pay attention to battery polarity, wrong polarity can damage transmitter!

BATTERY COVER
Remove battery cover in order to insert or replays batteries.

Body pack transmitter operation

ANTENNA
Antennas for RF signal transmitting to the receiver. Covered antenna can reduce working distance, try to keep antenna uncovered in order to guaranty maximum working distance.

LCD DISPLAY
Displays the current frequency, channel and low battery indication.

IR RECEIVER
IR receiver allows synchronize body pack and receiver by establishing body pack radio frequency to the same as set in receiver.

BATTERY COVER LOCK
Push cover lock in order to remove battery cover.

BATTERY HOLDER
Battery holder for two pieces of AA sizes alkaline batteries. Pay attention to battery polarity, wrong polarity can damage transmitter!

BATTERY COVER
Remove battery cover in order to insert or replays batteries.

POWER BUTTON
Press power button for 3 seconds to turn on/off the power.

MICROPHONE CONNECTOR
Balanced XLR and unbalanced 6,3mm Jack audio output.

Synchronization
Press infrared data transfer button (SYNC) on the first or second receivers to transmit data from receiver to transmitter in order to synchronize microphone and receiver radio frequency with you desired receiver’s side.

The distance between the devices should be proximally 20cm.

IMPORTANT: During synchronization IR receiver and IR transmitter should be directed to each other.

Receiver’s menu
Long press of SET button brings main menu on the screen, in order to enter the submenu press SET button one more time. Use navigation buttons to navigate menu and adjust settings.

F-MODE MENU
Activate F-mode menu by pressing SET button for 3 sec. This menu consists from TUNE, CHANNL and EXIT sub menu.

TUNE MENU
Select tune menu in order to change manually receiver’s frequency in 50 kHz steps.

CHANNEL MENU
Select CHANNL to set one of the 32 channel’s presets. Before the selecting CHANNL, the default display in the DISPLY menu should be set to CHANNL.

DISPLAY MENU
Display menu allows to change the default screen view from frequency to channel and otherwise. Select “CHANNL” to display channel number in the screen or select “FREQUE” to display channel frequency in Mhz.

SQUELCH MENU
The squelch level is adjustable in 5dB steps from 0dB to 20dB. Selecting a smaller value increase the squelch threshold, selecting a higher value reduce the squelch threshold. If the squelch threshold is set too high, the microphone working distance can be reduced.

VOLUME MENU
Select VOLUME menu to adjust audio output level.

LOCK MENU
Lock menu allows lock main panel buttons, except power and SETTING buttons. Please set lock function to off, for unlock.

EXIT MENU
Select to exit from menu.

Specifications

GENERAL
iLIVE 2×2 receiver

Power supply| 12-15 V DC, 1.25 A
Output| 2 x Balanced XLR , 1 x unbalanced 6,3 mm TS JACK
Receiver way| Two frequency conversion super-heterodynes
Intermediate frequency| 10,7 MHz
Antenna| BNC
T.H.D| < 0,7 %
Sensitivity| 6 dB μV
Image rejection| 36 dB
Max. audio output| 0 dB
Dimensions (H x W x D)| 420 mm X 44 mm X 183 mm
Weight| 2.3 kg
Material| Steel enclosure, aluminum front panel
iLIVE 2 handheld transmitter

Carrier frequency range| 606 MHz – 621 MHz
Modulation| FM
Channels| 32
Audio frequency response| 45 Hz – 18 kHz
S/N ratio| > 105 dB
Antenna| Built-in spiral antenna
Transmitter’s power| 3 mW
Working range| 60 m (Note: actual range depends on RF signal absorption, reflection and interference)
Polar pattern| Cardioid
Battery| 2 x 1,5 V AA Alkaline battery
Dimensions| 240 mm (lenght)
Weight| 302 g
Material| Aluminum
GENERAL
iLIVE 2 body pack transmitter

Carrier frequency range| 606 MHz – 621 MHz
Modulation| FM
Channels| 32
Audio frequency response| 45 Hz – 18 kHz
S/N ratio| > 105 dB
Antenna| 1/4 wave antenna
Input connector| 4 pin mini XLR connector
Transmitter’s power| 3 mW
Working range| 60 m (Note: actual range depends on RF signal absorption, reflection and interference)
Polar pattern| Cardioid
Battery| 2 x 1,5 V AA Alkaline battery
Dimensions| 110 mm x 64 mm x 25 mm
Weight| 76 g
Material| Plastic
GENERAL
HM

Capsule type| Condenser
Impedance| 200 Ω
Sensitivity| -47 dB
Frequency| 45 Hz – 18 kHz
Connectors| 4 pin mini XLR connector
Phantom power voltage| 5V DC
Cable length| 1 m
Weight| 15 g
Colour| Skin (RAL 1014)
Accessories| Windscreen
LM

Capsule type| Condenser
Impedance| 200 Ω
Sensitivity| -46 dB
Frequency| 50 Hz – 18 kHz
Connectors| 4 pin mini XLR connector
Phantom power voltage| 5 V DC
Cable length| 1 m
Weight| 21 g
Colour| Black (RAL 1017)
Accessories| Windscreen

The specifications are correct at the time of printing this manual. For improvement purposes, all specifications for this unit, including design and appearance, are subject to change without prior notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>