Walmart GC-200 200 Inch Large Studio Electric Projection Screen User Guide
- June 25, 2024
- Walmart
Table of Contents
Walmart GC-200 200 Inch Large Studio Electric Projection Screen
MOUNTING INSTRUCTIONS FOR Large Studio Motorized
Projection Screen
After installation please store instructions for future reference
IMPORTANT SAFETY INSTRUCTIONS
WARNING : To reduce the risk of fire or electric shock, do not expose to rain or moisture.
- Read and follow all instructions and warnings in this manual. Keep for future reference.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Do not block any ventilation openings. Install according to manufacturer’s instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Do not override the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades – one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the outlet receptacle.
- Protect the power cord from being walked on or pinched, particularly at the plug, convenience receptacles, and the point where it exits from the apparatus.
- Only use attachments/ accessories specified by the manufacturer.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as when the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
- Do not expose this equipment to dripping or splashing, ensure that no objects filled with liquids, such as vases or drinking vessels, are placed on the equipment.
- To completely disconnect this equipment from the A/C mains, disconnect the power supply cord plug from the A/C receptacle.
- To avoid overheating the motor, do not continually raise and lower the screen for over 3 minutes or more than 6 times. If the moter begins to overheat, a thermal cut out will automatically cut power to the motor. The motor will then require a cool-down time of approximately 3 minutes before the screen will work again. This safety feature helps to prevent overheating of the motor.
Cleaning and Maintenance
- Do not clean the screen case with water. Use a clean dry cloth to clear dust and dirt regularly.
- To clean non-coated screen material, use warm soapy water only. Never use chemicals or abrasives, as this will damage the surface of the material, which will impact the viewing quality of your screen.
NEVER clean a coated screen with water. Use a clean, dry cloth to remove dust, dirt, or debris. In some cases, a blower can be used to remove dust from large areas of the screen surface.
tools required
Power connection
INSTALLATION (aluminum case)
- Assemble the bracket and the eye nut as below :
- Slide the M6 screws into two rails on the top of the casing, fix the bracket and eye nut set in the proper position using M6 bolts.
- Hang the screen onto the lifting points which were pre-installed by customer. Always ensure the screen is secured to a strong surface such as wood, steel, or concrete.
NOTE: Screens may have more anchor points than pictured, depending on size. For safety reasons, a minimum of 3 anchor points must be used for all installations.
-
Wall Mount
Using a tape measure, measure the distance between the keyholes on the casing. (Figure 1 ). According to the measurement, use the drill to drill identical holes of the appropriate size (use a smaller drill bit than the actual screws) on the wall and ensure that it is level (Figure 2 and 3). Screw in the appropriate screws, ,t, 12 x so plus anchors, leaving enough space al the end lo hang the casing (Figure 4 ). Always ensure the screen is anchored to a sturdy material such as wood, concrete, or steel. To ensure that the screen is level, use a leveler to check (Figure 5). -
NOTE: Screens may have more anchor points than pictured, depending on size. For safety reasons, a minimum of 3 anchor points must be used for all installations.
-
Ceiling Mount
-
Using a tape measure, measure the distance between the rings for hanging on the casing. (Figure 1 ). According to the measurement, use the drill to drill identical holes of the appropriate size (use a smaller drill bit than the actual hook screws) on the ceiling and ensure that it is level (Figure 2 and 3). Screw in the hook screws (not provided), and lift the screen into the hooks screws to hang (Figure
-
Always ensure the hooks are secured to a sturdy material such as wood, steel, or concrete. To ensure that the screen is level, use a leveler to check (Figure 5).
NOTE: Screens may have more anchor points than pictured, depending on size. For safety reasons, a minimum of 3 anchor points must be used for all installations.
-
Without mounting bracket installation
INSTALLATION (Sectioned Case)
- Ceiling Mount
- Using a tape measure, measure the distance between the two rings for hanging on the casing. (Figure 1 ). According to the measurement, use the drill to drill identical holes of the appropriate size (use a smaller drill bit than the actual hook screws) on the ceiling and ensure that it is level (Figure 2 and 3). Screw in the hook screws (not provided), and lift the screen into the hook screws to hang (Figure 4 ). To ensure that the screen is level, use a level to check (Figure 5).
RF Remote Pairing
Note: The provided RF remote is paired with the screen in the factory.
These steps are necessary only if the remote has to be replaced, or when
troubleshooting remote control issues.
To pair the RF remote, use the following steps:
- Remove the screw from the bottom of the control box (near the power cord), open the control box, and locate the remote pairing button.
- Using the manual buttons, lower the screen 8-10 inches.
- Press and hold the pairing button for 3 seconds, or until the screen moves up and down once.
- Within 8 seconds, press and hold the UP button on the RF remote control until the screen moves up and down again.
- Test the remote to ensure it controls the screen. If it is still not working correctly, repeat steps 2-3 as necessary. Make sure step 3 is completed within 8 seconds of releasing the pairing button.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>