Walmart A05086 Down Pendant Light Instruction Manual
- June 1, 2024
- Walmart
Table of Contents
Walmart A05086 Down Pendant Light
Product Information
Specifications
- Item Number: A05086
- Voltage: 120V
- Maximum Wattage: LED, 5W
Product Usage Instructions
Tools Required
- Ladder
- Philips Head or Flat Blade Screwdriver
- Electrical Tape
- Pliers
- Wire Cutter/Stripper
Parts Included
- (A) Mounting plate (1)
- (B) Green ground screw (1)
- (E) Screw (2)
- (F) Canopy (1)
- (G) Lock nut (1)
- (H) Cable (1)
- (I) Body (1)
- (J) Crystal (1)
- (K) Nut (2)
Assembly & Installation Instructions
- Carefully remove the fixture from the carton and check that all parts and accessories are included.
- Turn off the power before starting the installation.
- Remove mounting plate (A).
- Screw nuts (K) into holes to secure the crystal (J) and body (I) with an Allen wrench (L) and mounting screws (D).
- Connect wires as shown in the charts provided.
FAQ
Q: Can I use a higher-wattage bulb than specified?
A: No, the maximum wattage is LED, 5W. Using a higher-wattage bulb may damage the product.
Q: Can I install the product on a slanted ceiling?
A: It is recommended to install the product on a flat, strong surface. Installation on a slanted ceiling may affect stability.
Item Number: A05086
WARNING (To reduce the risk of fire, electric shock, or personal injury):
- We suggest installation by a licensed electrician.
- Please read the instructions carefully and save them as you may need it at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home.
- Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- The mounting surface should be clean, dry, flat, strong enough, and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is LED, 5W.
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution, and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED
(NOT INCLUDED)
Before starting assembly and installation please prepare the needed tools as
below picture
PARTS TYPE & QTY INCLUDED
- (A ) Mounting plate (1)
- (B) Green ground screw (1)
- (E) Screw (2)
- (F) Canopy (1)
- (G) Lock nut (1)
- (H) Cable (1)
- (I) Body (1)
- (J) Crystal (1)
- (K) Nut (2)
ACCESSORIES & QTY ENCLOSED:
- (C) Plastic wire connector (3)
- (D) Mounting screw (2)
- (L) Allen wrench (1)
ASSEMBLY & INSTALLATION INSTRUCTIONS
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
- Turn off power
- Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home.
- Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- Unscrew screws (E) from canopy (F).
- Remove mounting plate (A).
- Align holes of crystal (J) and holes of body (I).
- Screw nuts (K) into holes to secure the crystal (J) and body (I) with Allen wrench (L)
- Screw nuts (K) into holes to secure the crystal (J) and body (I) with Allen wrench (L)
- Attach mounting plate (A) to the outlet box with mounting screws (D).
- Make wire connections
- Connect wires as shown in the charts below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
- Connect ground wires according to the chart below
- Connect wires according to the chart below
- Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)
- Twist wires together with plastic wire connectors until tightly joined.
- Wrap each connector with approved electrical tape.
- Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
- Raise canopy (F) to the ceiling and secure canopy (F) in place by tightening screws (E) onto the pre-assembled screws in mounting plate (A).
- Note: canopy (F) should be snug against the ceiling and screws (E).
- If not, adjust the threaded length on the mounting plate (A).
- Unscrew the pre-assembled hex nuts.
- Screw the pre-assembled screws in or out of the mounting plate (A).
- When the secure length is achieved, tighten the hex nuts and back to step 6.
- To adjust the hanging height of the fixture:
- Press down and hold the lock nut (G) by hand.
- Pull or push cable (H) in and out of canopy (F) to increase or decrease the hanging height.
- Check that everything is installed properly, then you can turn on the light. We hope you enjoy your new lighting!
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>