Walmart Full Size Daybed Installation Guide

Walmart Full Size Daybed Installation Guide

Limited 1 year Warranty

We warrant this product to be free from defects in material and workmanship and agrees to remedy any such defect. This warranty covers one year from the date of original purchase from authorized retailers. This is solely limited to the repair or replacement of defective parts and assembly labor is not included. This warranty does not apply to any product which has been improperly assembled, subjected to misuse or abuse or which has been altered or repaired in any way.The warranty does not cover wearing, tearing, fading or splitting of the fabric (where applicable. Liability for consequential damages is excluded to the extent exclusion is permitted by law. This warranty gives you specific legal rights and you may also have other rights which vary from state to state or province to province. To obtain warranty service, purchaser must present original bill of sale. Components repaired or replaced are warranted through the remainder of the original warranty period only. The defective components will be repaired or replaced without charge, subject to the terms and conditions described above.

Contact Us!
For help with assembly, identifying parts, product information or to order parts, please contact us

Read Before Beginning Assembly

• Work in a spacious area and near where the unit will be used, preferably on a carpet, or use a piece of the cardboard packaging to protect your floor and product.
• Make sure all parts are included. Most parts are labeled or stamped on the raw edge.
• Read each step carefully. It is very important that each step of the instructions is performed in the correct order. If these steps are not followed in sequence, assembly difficulties will occur.
• This product may contain small components. Please ensure that they are kept away from small children.
• This product is designed for home use and is not intended for commercial use.

Do NOT use powertools

Phillips head screwdriver needed (not included)

OVERVIEW

PARTS LIST

 Each part has a unique part number. Please reference the appropriate part number when contacting customer service for replacement parts.
 Before throwing any packaging, please verify all contents and make sure you have received all the parts listed above!

HARDWARE LIST

Hardware Pack

 Please do not completely tighten all the hardware, until the entire assembly is complete, unless otherwise indicated in the step-by-step instructions.
 The screw(s), bolt(s) to be used at each step are shown in actual size in the lower right corner of the.

Step 1
Insert stoppers (6) and frame slats J x 24 into the bottom rail s I x 2 and push down until firmly in place. Attach the top rail s H x 2 onto the top of frame slat s J. Insert wood dowels (3) into the ends of the rails (H & I) x 2. Attach posts A & C and posts B & D to rail s H & I with wood joint connector bolts (5) as shown. Use Allen key (7) to install the bolts.

Step 2
Insert stoppers (6) and frame slats G x 17 to the bottom rail F and push down until firmly in place. Attach the top rail E onto the top of frame slats G. Insert wood dowels (3) into ends of rails E & F. Attach post A & B to rail E & F with wood joint connectors (5) as shown. Insert barrel nuts (2) into side rail K as shown below. Attach the side rail K to the posts using joint connectors (1) .
NOTE: Do not fully tighten the bolts. This will facilitate assembly in the following steps.

Step 3
Insert barrel nuts (2) into side rail K as shown. Attach the side rail K to the posts C & D using joint connectors (1).
NOTE: Tighten all bolts previously installed

Step4
Attach slats L as shown below to side rails K with flat head wood screws (4) using a Phillips head screw driver (not included). Use space blocks A1 to space them out evenly as show

CAUTION: This unit is intended for use only with the products and/or maximum weights indicated. Use with other products and/or products heavier than the maximum weights indicated may result in instability or cause possible injury

Helpful Hints

• Move your new furniture carefully, with two people lifting and carrying the unit to its new location.
• Your furniture can be disassembled and reassembled to move.
• Clean the product with a soft damp cloth. DO NOT use harsh chemicals or abrasive cleaners.
• Check bolts and nuts periodically and tighten if necessary

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>