Diso MH802 TWS Earbuds User Manual
- June 24, 2024
- Diso
Table of Contents
Diso MH802 TWS Earbuds User Manual
About MH802
Product specification
- Bluetooth specification: support Bluetooth V4.2 HFP V1.7 HSP V1.2 A2DP V1.3 AVRCP V1.6
- Standby time: 80hours
- Support voice guide
- Talking time: 3 hours
- Playing time: 2-2.5hours(depends on different volume and songs)
- Distance: up to 10 meters.
Wearing
Matching the earbuds with earphones
Putting on the earphone and turn the earphone as picture
- For optimal audio performance, select the ear tip size that gives you the best comfort
- Each earphone is marked with an L or an R. Be sure to wear the correct one.
- Tuck the tip under the ear ridge until they are secure.
Note: for safety, please use the smaller size earbuds than your normal size earbuds when doing outdoor sports and make sure you can hear the outside sounds.
How to use
Use in pair
Turn on earphone
- Turn on each earphone, and press the MFB button for 3 seconds on both earphones at the same time till the LED flashes blue. There will be a voice prompt “Power on”
- After turning on the earphones, the left and right earphones will automatically connect with the voice prompt “beep” “connected” “left channel” “right channel”
Pairing device
- After each earphone is connected, you will hear a single beep in the right channel and a voice prompt “pairing”. Only the right unit will be flashing red and blue during this time.
- Turn on the mobile phone Bluetooth and search mode name “DISO”, clicking it for connecting.
- After connecting, the LED will flash blue. There will be a voice prompt “Second device is connected”
- The next time earphone is turned on, they will automatically Search for and attempt to connect to the last paired device.
Receiving and Ending a call
- Click the right earphone MFB button once
Rejecting a call
- Double-click the right earphone MFB button when a call is incoming
Note: You can listen to music and make phone calls. When listening to a phone call, only the right earphone will have sound.
Accessories
Use single earphones
- Turn on the left earphone or right earphone by pressing 3 seconds till the LED flashes blue. This will enter the pairing mode and red and blue LED flashing.
- Turn on the mobile phone Bluetooth and search mode name “DISO” if using the right earphone/”L channel” for the left earphone, clicking it to connect.
- After connecting, the LED will flash blue. There will be a voice prompt “connected”.
- The next time earphone is turned on, they will automatically Search for and attempt to connect to the last paired device.
Listen to music
- Click the MFB button for music to play and pause
- Double-click the right earphone MFB button to track forward
- Double-click the left earphone MFB button to track back
Charging
Charge the charging box
- Plug in the USB cable to the charging box
- When charging, the red LED indicator turns on.
- When fully charging, about 2 hours, the red LED indicator turns off and the blue LED indicator turns on.
Charge the earphone
Put the earphones in the charging box and close the box. There is a red LED
indicator on the earphones. When fully charged, after about 1 hour, the
earphone has a red LED the indicator will be blue.
Note: When earphones are charged full, to save power, after 1 minute LED
will be turned off
-
Charge the charging box:
-
Charge the earphone
Note : The earphone’s gold pin needs to connect with the charging box gold pin. -
If putting earphones in a box with the wrong position, ear– the phone will fail to charge.
FCC STATEMENT
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
DISO INC
www.disosport.com
Email:diso@disosport.com
Download PDF:Diso MH802 TWS Earbuds User Manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>