Cyber Power B602RC1GY 6 Outlet Surge Protector User Manual

: June 22, 2024
: Cyber Power

Table of Contents

Cyber Power B602RC1GY 6 Outlet Surge Protector
Product Information
Product Usage Instructions
FEATURES
SPECIFICATIONS
TROUBLESHOOTING
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Cyber Power B602RC1GY 6 Outlet Surge Protector

Product Information

Specifications

Model Number: B602RC1
Outlets: 6 Standard Outlets
Power Cord Length: 2 feet
Surge Protection: 500 Joules
Electrical Rating: 125 V / 15 A / 60 Hz / 1875 W
UL Clamping Voltage: 800 V (L-N)
Maximum Peak Current: 15,000 A
AC Lines Protected: L-N: 15,000 A
Response Time: Less than 1 nanosecond
Circuit Breaker: Resettable 15 Amp

Product Usage Instructions

Features

ON/OFF Reset Control Switch and Circuit Breaker:
Controls power to all outlets. The switch acts as a 15A breaker. In case of an overload, it will automatically switch off. To resume operation, remove the overload condition and reset by switching it ON.
Standard Grounded Outlets (6)
2-ft Power Cord
Keyhole Mounting Slots (on back)

FAQ – Frequently Asked Questions

Troubleshooting

If the ON/OFF is switched OFF: The 15 Amp circuit breaker may have tripped. Check connected devices for overloading and remove the problematic device. Reset by turning the ON/OFF switch back to RESET.

For More Information

Technical Support: Visit CyberPowerSystems.com/support or call Toll-Free: 1-877-297-6937

Conformance Approvals:
This device complies with Part 15 of the FCC Rules. It should not cause harmful interference and must accept any received interference, including that leading to undesired operation. Any changes not approved by the compliance party could void the user’s authority to operate the equipment.

WARNING: This product contains chemicals like bisphenol A (BPA) and styrene (ABS), known to the State of California to cause reproductive harm and cancer. For more information, visit www.P65Warnings.ca.gov.

YOUR ULTIMATE ALLY IN POWER

6-OUTLET
SURGE PROTECTOR
B602RC1GY
B602RC1HPK
B602RC1DBL

USER MANUAL

Cyber Power Systems (USA), Inc.
4241 12th Avenue East, Suite 400 | Shakopee, MN 55379 CyberPowerSystems.com

FEATURES

ON/OFF Reset Control Switch and Circuit Breaker Controls power to all outlets. The switch is also a 15A breaker. When an overload occurs, it will automatically switch off. To resume operation, ensure the overload condition is removed and reset the surge protector by switching the unit ON.
Standard Grounded Outlets (6)
2-ft Power Cord
Keyhole Mounting Slots (on back)

SPECIFICATIONS

Model Number: B602RC1
Outlets: 6 Standard Outlets
Power Cord Length: 2 feet
Surge Protection: 500 Joules
Electrical Rating: 125 V / 15 A / 60 H / 1875 W
UL Clamping Voltage: 800 V (L-N)
Maximum Peak Current: 15,000 A
AC Lines Protected: L-N: 15,000 A
Response Time: Less than 1 nanosecond
Circuit Breaker: Resettable 15 Amp

WARNING: This product can expose you to chemicals including bisphenol A (BPA) and styrene (ABS), which is known to the State of California to cause reproductive harm and cancer. For more information, go to www.P65Warnings.ca.gov.

CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK:

Use only in dry locations and only indoors.
DO NOT plug into another relocatable power tap.
DO NOT “daisy chain” surge protectors.
DO NOT use with any aquarium equipment.
DO NOT use if properly grounded outlets are not available.
DO NOT install this device if there is less than 10 meters (30 feet) of wire between the electrical outlet and electrical service panel.
DO NOT use for medical or life support equipment. This device features an internal protection that will disconnect the surge protective component at the end of its useful life, but it will maintain unprotected power to the load.

TROUBLESHOOTING

If the ON/OFF is switched OFF, the 15 Amp circuit breaker may have tripped. Examine your connected equipment and remove the device that is overloading the circuit. Then, turn the ON/OFF switch back to RESET.

FOR MORE INFORMATION
Visit CyberPowerSystems.com for more information regarding:

Product information and certifications
Product warranty
Connected equipment guarantee

TECHNICAL SUPPORT
Visit: CyberPowerSystems.com/support
Toll-Free: 1-877-297-6937
© 2024 Cyber Power Systems (USA), Inc. All rights reserved. All other trademarks are the property of their respective owners.

CONFORMANCE APPROVALS
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interfer-ence to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.