Einhell TP-CD18 Cordless Hammer Drill Screwdriver Instruction Manual

Einhell TP-CD18 Cordless Hammer Drill Screwdriver

Specifications:

• Voltage: 18 V d.c.
• No-load Speed: 0-500 / 0-1800 min-1
• Torque Settings: 20+1+1
• Forward/Reverse Rotation: Yes
• Chuck Capacity: Max. 13 mm
• Weight: 1.69 kg
• Sound Pressure Level: 87.7 dB(A)
• Sound Power Level: 98.7 dB(A)
• Vibration Values:
  • Drilling in Metal: 2.5 m/s2 (Uncertainty K = 1.5 m/s2)
  • Impact Drilling in Concrete: 10.15 m/s2 (Uncertainty K = 1.5 m/s2)

Product Usage Instructions

Before Operating:
Prior to using your cordless hammer drill/screwdriver, ensure you have read the following instructions:

1. Charge the battery using the provided charger.
2. Inspect the tool for any damage or missing parts.
3. Ensure proper safety gear is worn during operation.

Charging the LI Battery Pack :

1. Remove the battery pack from the handle.
2. Insert the battery pack into the charger until fully charged.

Operating Modes:
Switch between screwdriving, drilling, and impact drilling using the mode selector switch.

Torque Adjustment:
Adjust the torque setting as needed for different tasks using the torque adjustment dial.

Battery Status Indicator :
Refer to the LED indicators to determine the battery charge level. All three LEDs lit indicate a fully charged battery.

Frequently Asked Questions (FAQ):

• Q: What should I do if the battery pack fails to charge?
  A: If charging issues persist, please contact our customer service for assistance.

• Q: Can I switch between operating modes while the tool is in use?
  A: It is recommended to only switch torque settings and operating modes when the tool is not in operation to avoid damage.

Danger!
When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations with due care. Keep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, hand over these operating instructions and safety regulations as well. We cannot accept any liability for damage or accidents which arise due to a failure to follow these instructions and the safety instructions.
Explanation of the symbols used (see Fig. 9)

1. Danger! – Read the operating instructions to reduce the risk of injury.
2. Caution! Wear earmuff s. The impact of noise can cause damage to hearing.
3. Caution! Wear a breathing mask. Dust which is injurious to health can be generated when working on wood and other materials. Never use the device to work on any materials  containing asbestos!
4. Caution! Wear safety goggles. Sparks generated during working or splinters, chips and dust emitted by the device can cause loss of sight.
5. Store the batteries only in dry rooms with an ambient temperature of +10°C to +40°C. Place only fully charged batteries in storage (charged at least 40%).
6. Change the gear only when the drill is at a standstill. If you fail to observe this point, the gearing may be damaged.
7. Safety class II
8. For use in dry rooms only.

 Safety regulations

The corresponding safety information can be found in the enclosed booklet.
Warning!

• Read all the safety information, instructions, illustrations and technical data provided on or with this power tool. Failure to adhere to the following instructions may result in electric shock, fi re and/or serious injury.
• Keep all the safety information and instructions in a safe place for future use.

Layout and items supplied

Layout (Fig. 1)

1. Torque selector
2. Battery capacity indicator
3. Changeover switch
4. ON/OFF switch
5. Battery pack (it is not included in delivery)
6. Battery charger (it is not included in delivery)
7. Selector switch for 1st/2nd gear
8. Pushlock button
9. Quick-change drill chuck
10. LED lamp
11. Additional handle
12. Selector switch for driving/drilling/impact drilling

Items supplied
Please check that the article is complete as specified in the scope of delivery. If parts are missing, please contact our service center or the sales outlet where you made your purchase at the latest within 5 working days after purchasing the product and upon presentation of a valid bill of purchase. Also, refer to the warranty table in the service information at the end of the operating instructions.

• Open the packaging and take out the equipment with care.
• Remove the packaging material and any packaging and/or transportation braces (if available).
• Check to see if all items are supplied.
• Inspect the equipment and accessories for transport damage.
• If possible, please keep the packaging until the end of the guarantee period.

Important!
The equipment and packaging material are not toys. Do not let children play with plastic bags, foils or small parts. There is a danger of swallowing or suffocating!

• Cordless drill/screwdriver
•  Additional handle
• Original operating instructions
• Safety instructions

Proper use

• The cordless impact drill/driver is designed for tightening and undoing screws, for drilling in wood, metal and plastic, and for impact drilling in stone, in each case when using the appropriate bits.
• The equipment is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user /operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this.

Technical data

• Voltage supply ………………………………….18 V d.c.
• Idling speed: ……………………….0-500/0-1800 rpm
• Torque settings: ………………………………… 20+1+1
• Forward and reverse rotation ……………………..yes
• Chuck clamping width …………………..max. 13 mm
• Weight……………………………………………….1.69 kg

The maximum screw diameter indicates the ma-ximum diameter of the screw that can be screwed into wood. The screw diameter can vary depen-ding on the type of wood.
Danger!
Sound and vibration
Sound and vibration values were measured in accordance with EN 62841.

• LpA sound pressure level ………………… 87,7 dB(A)
• KpA uncertainty ………………………………………5 dB
• LWA sound power level ……………………. 98,7 dB(A)
• KWA uncertainty ………………………………………5 dB

Wear ear-muffs.

• The impact of noise can cause damage to hearing.
• Total vibration values (vector sum of three directions) determined in accordance with EN 62841.
• Drilling in metal
  • Vibration emission value ah ≤ 2.5 m/s2
  • K uncertainty = 1.5 m/s2
• Impact drilling in concrete
  • Vibration emission value ah,ID = 10.15 m/s2
  • Uncertainty K = 1.5 m/s2

The stated vibration emission levels and stated noise emission values were measured in accordance with a set of standardized criteria and can be used to compare one power tool with another.
The stated vibration emission levels and stated noise emission values can also be used to make an initial assessment of exposure.
Warning:

• The vibration and noise emission levels may vary from the level specifi ed during actual use, depending on the way in which the power tool is used, especially the type of workpiece it is used for.
• Keep the noise emissions and vibrations to a minimum.
• Keep the noise emissions and vibrations to a minimum.
• Only use appliances which are in perfect working order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use. Caution!

Residual risks

Even if you use this electric power tool in accordance with instructions, certain residual risks cannot be rules out. The following hazards may arise in connection with the equipment’s construction and layout:

1. Lung damage if no suitable protective dust mask is used.
2. Damage to hearing if no suitable ear protection is used.
3. Health damage caused by handarm vibrations if the equipment is used over a prolonged period or is not properly guided and\ maintained.

Limit the operating time.
All stages of the operating cycle must be considered (for example, times in which the electric tools are switched off and times in which the tool is switched on but operates without load).

Before starting the equipment
Be sure to read the following information before you use your cordless screwdriver for the first time:

1.  Charge the battery pack with the charger supplied.
2. Only ever use sharp drill bits and screwdriver bits which are suitable for the purpose and in faultless condition.
3. Always check for concealed electric cables and gas and water pipes when drilling and screwing in walls.

 Operation

1. Charging the LI battery pack (Fig. 2-3)
2. Remove the battery pack (5) from the handle, pressing the pushlock buttons (8) downwards to do so.
3.  Check that your mains voltage is the same as that marked on the rating plate of the battery charger. Insert the power plug of the charger (6) into the mains socket outlet. The green LED will then begin to fl ash.
4.  Push the battery pack onto the battery charger.

In section 10 “Charger indicator” you will fi nd a table with an explanation of the LED indicator on the charger.
If the battery pack fails to become charged, please check

• whether there is voltage at the socket-outlet
• whether there is proper contact at the charging contacts on the charger.

If the battery still fails to become charged, please return

• the charger
•  the battery pack to our Customer Service Department.

To ensure that items are properly packaged and delivered when you send them to us, please contact our customer service or the point of sale at which the equipment was purchased.

• When shipping or disposing of batteries and cordless tools, always ensure that they are packed individually in plastic bags to prevent short circuits and fi res.
• To ensure that the LI battery pack provides long service you should take care to recharge it promptly. You must recharge the battery pack when you notice that the power of the cordless screwdriver drops.
• Torque setting (Fig. 4 /Item 1) Important! The tool must be at a standstill when you set the torque with the setting ring. The cordless screwdriver is fi tted with a mechanical torque selector.

The torque for a specifi c size of screw is selected with the set-collar (1). The correct torque depends on several factors:

• on the type and hardness of material in question
• on the type and length screws used
• on the requirements needing to be met by the screwed joint.
• The clutch disengages with a grating sound to indicate when the set torque is reached.

Selector switch for driving/drilling/impact drilling (Fig. 4/Item 12)

• For driving purposes, set the selector switch
  (12) to the „Screw“ position. The torque is adjusted via the torque setting (1) (see point 6.2).

• For drilling purposes, set the selector switch (12) to the „Bit“ position. The slip coupling is now off and the maximum torque is available regardless of the torque setting (1).

• For impact drilling purposes, set the selector switch (12) to the „Hammer“ position. The slip coupling is now off and the maximum torque is available regardless of the torque setting (1).

• Important! Change the torque setting (1) and the selector switch for driving/drilling/impact drilling (12) only when the equipment is at a standstill.

•  Forward/Reverse switch (Fig. 5 /Item 3) With the slide switch above the On/Off switch you can select the direction of rotation of the battery-powered drill/screwdriver and secure it against being switched on accidentally. You can choose between clockwise and anticlockwise rotation. To avoid causing damage to the gearing it is advisable to change the direction of rotation only when the tool is at a standstill. The On/Off switch is blocked when the slide switch is in centre position.

• On/Off switch (Fig. 5 /Item 4)

• Infinitely variable speed control is possible with the On/Off switch. The further you press the switch, the higher the speed of the battery-powered drill/screwdriver.

Changing over from 1st gear to 2nd gear (Fig. 4 /Item 7)

• You can work at a higher or lower speed depending on the position of the selector switch. To avoid damaging the gear unit you should only change over gears when the tool has stopped.
• Battery capacity indicator (Fig. 6 – Item 2) Press the battery capacity indicator switch (a). The battery capacity indicator (2) shows the charge status of the battery using 3 LEDs.
• All 3 LEDs are lit:
  • The battery is fully charged.
• 2 or 1 LED(s) are lit:
  • The battery has an adequate remaining charge.
• 1 LED fl ashes:
  • The battery is empty, recharge the battery.
• All LEDs blink:
• The battery temperature is too low. Remove the battery from the equipment, keep it at room temperature for one day. If the fault reoccurs, this means that the rechargeable battery has undergone exhaustive discharge and is defective. Remove the battery from the equipment. Never use or charge a defective battery.
• LED lamp (Fig. 6 /Item 10)
  The LED lamp (10) can be used in poor lighting conditions to illuminate the area where you want to drill or screw. The LED lamp (10) will be lit automatically as soon as you press the ON/OFF switch (4).

Changing the tool (Fig. 7)
Important. Set the changeover switch (3) to its centre position whenever you carry out any work (for example changing the tool, maintenance work, etc.) on the cordless screwdriver.

• The cordless screwdriver is fitted with a quick-action chuck (9) with an automatic spindle stop.
• Open the chuck (9). The chuck opening (a) must be large enough to hold the tool (drill bit or screwdriver bit).
• Select the suitable tool. Push the tool as far as possible into the chuck opening (a).
• Tighten the chuck (9) and then check that the tool is secure.

Screwdriving
We recommend using self-centering screws (e.g. recessed head screws) designed for reliable working. Be sure to use a bit that matches the screw in shape and size. Set the torque, as described elsewhere in these operating instructions, to suit the size of screw.

Mounting the additional handle (Fig. 8 /Item 11)

• The additional handle (11) enables you to achieve better stability while using the equipment.
• Do not use the equipment without the additional handle.
• The additional handle (11) can be screw-fitted in two positions (A, B). It is suitable therefore for right-handed and left-handed users.

 Cleaning, maintenance and ordering of spare parts

Danger!
Always pull out the battery pack before starting any cleaning work.
Cleaning

• Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure.

• We recommend that you clean the device immediately each time you have finished using it.

• Clean the equipment regularly with a moist cloth and some soft soap. Do not use  cleaning agents or solvents; these could attack the plastic parts of the equipment. Ensure that no water can seep into the device. The ingress of water into an electric tool increases the risk of an electric shock.

• Maintenance
  There are no parts inside the equipment which require additional maintenance.

• Ordering spare parts and accessories Please provide the following information when ordering spare parts:

  • Type of unit
  • Article number of the unit
  • ID number of the unit
  • Spare part number of the required spare part For our latest prices and information please go to www.Einhell-Service.com

Tip! For good results we recommend high-quality accessories from ! www.kwb.euwelcome@kwb.eu

Disposal and recycling
The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. Never place defective equipment in your household refuse. The equipment should be taken to a suitable collection center for proper disposal. If you do not know the whereabouts of such a collection point, you should ask in your local council offices.

Storage

Store the equipment and accessories out of children’s reach in a dark and dry place at above freezing temperature. The ideal storage temperature is between 5 and 30 °C. Store the electric tool in its original packaging.

Charger indicator

• Ready for use
  • The charger is connected to the mains and is ready for use; there is no battery pack in the charger

On| Off|

• Charging
• The charger is charging the battery pack in quick charge mode. The charging times are shown directly on the charger.
• Important! The actual charging times may vary slightly from the stated charging times depending on the existing battery charge.

Off| On|

• The battery is charged and ready for use. (READY TO GO)
• The unit then changes over to gentle charging mode until the battery is fully charged.
• To do this, leave the rechargeable battery on the charger for approx. 15 minutes longer.
• Action:
• Take the battery pack out of the charger. Disconnect the charger from the mains supply.

Flashing| Off| Adapted charging

• The charger is in gentle charging mode.
• For safety reasons the charging is performed less quickly and takes more time. The reasons can be:
  •  The rechargeable battery has not been used for a very long time.
  • The battery temperature is outside the ideal range.
• Action:
• Wait for the charging to be completed; you can still continue to charge the battery pack.

Flashing| Flashing|

• Fault
  • Charging is no longer possible. The battery pack is defective.
• Action:
  • Never charge a defective battery pack. Take the battery pack out of the charger.

On| On|

• Temperature fault

  • The battery pack is too hot (e.g. due to direct sunshine) or too cold (below 0° C).

• Action:
  

  • Remove the battery pack and keep it at room temperature (approx. 20° C) for one day .

For EU countries only

• Never place any electric power tools in your household refuse.
• To comply with European Directive 2012/19/EU concerning old electric and electronic equipment and its implementation in national laws, old electric power tools have to be separated from other waste and disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot.
• Recycling alternative to the return request:
• As an alternative to returning the equipment to the manufacturer, the owner of the electrical equipment must make sure that the equipment is properly disposed of if he no longer wants to keep the equipment. The old equipment can be returned to a suitable collection point that will dispose of the equipment in accordance with the national recycling and waste disposal regulations. This does not apply to any accessories or aids without electrical components supplied with the old equipment.
• Please note that batteries and lamps (e.g. light bulbs) must be removed from the tool before it is disposed of.
• The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of the
• Einhell Germany AG.
• Subject to technical changes.
• This consignment contains lithiumion batteries.
• In accordance with special provision 188 this consignment is not subject to the ADR regulations. Handle with care. Danger of ignition in case of damage to the consignment package. If the consignment package is damaged: Check and if necessary repackage. For further information contact: 0049 1807 10 20 20 66 (fixed network 14 ct/min, mobile phone max. 42 ct/min) Outside Germany charges will apply instead for a regular call to a landline number in Germany.

Service information

• We have competent service partners in all countries named on the guarantee certificate whose contact details can also be found on the guarantee certificate. These partners will help you with all service requests such as repairs, spare and wearing part orders or the purchase of consumables.
• Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required for use as consumables.

Not necessarily included in the scope of delivery!
In the eff ect of defects or faults, please register the problem on the internet at www.Einhell-Service.com. Please ensure that you provide a precise description of the problem and answer the following questions in all cases:

• Did the equipment work at all or was it defective from the beginning?
• Did you notice anything (symptom or defect) prior to the failure?
• What malfunction does the equipment have in your opinion (main symptom)?Describe this malfunction.

Warranty certificate

Dear Customer,
All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that this equipment develops a fault, please contact our service department at the address shown on this guarantee card. You can also contact us by telephone using the service number shown. Please note the following terms under which guarantee claims can be made:

1. These guarantee terms apply solely to consumers, i.e. natural persons, who do not want to use this product in connection with either their commercial or other self-employed activities. These guarantee terms regulate additional guarantee services which the undermentioned manufacturer promises to buyers of its new products in addition to their statutory rights of guarantee. Your statutory rights of guarantee are not affected by this guarantee. Our guarantee is free of charge to you.
2. The guarantee services cover only defects due to material or manufacturing faults on the new product which you have bought in the European Union from the undermentioned manufacturer and are limited to either the rectifi cation of said defects or the replacement of the product, whichever we prefer. Please note that only equipment under the brand name “Professional” has been designed for use in commercial, trade or professional applications. For all other products the guarantee is invalidated if the equipment is used within the guarantee period in commercial, trade or industrial applications or for other equivalent activities.
3. Our guarantee does not cover:
   • Damage to the equipment caused by failure to comply with the installation/assembly instructions or by unprofessional installation; damage caused by failure to comply with the operating instructions (e.g. connection to the wrong mains voltage or current type); damage caused by failure to comply with the maintenance and safety regulations; damage caused by exposing the equipment to abnormal environmental conditions; damage resulting from poor care and maintenance.
   • Damage to the equipment caused by misuse or incorrect applications (e.g. overloading the equipment or using nonapproved attachments or accessories); damage caused by foreign bodies (e.g. sand,  tones, dust, ….) getting inside the equipment. Damage in transit; damage caused by force or external influences (e.g. by dropping the equipment).
   • Damage to the equipment or parts of the equipment which is owed to use related, normal or otherwise natural wear. For example, batteries and battery packs are manufactured with a cycle limit for design-related reasons. Wear is negatively influenced in particular by load demands and charging speeds as well as exposure to heat, cold, vibration and impact.
4. The guarantee is valid for a period of 2 years starting from the purchase date of the equipment. Guarantee claims must be submitted before the end of the guarantee period and within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the equipment even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fitted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or for any replacement parts fitted. This also applies if on-site service is used.
5. To assert your guarantee claim, register the defective equipment at: www.Einhell-Service.com. You will need to provide proof of purchase of the new item of equipment. Equipment returned without such proof or without a rating plate are excluded from the guarantee services because of the lack of traceability. If the defect is covered by our guarantee, then either the item in question will be repaired immediately and returned to you or we will send you a new replacement.
6. If you have taken the equipment with you to a different EU country than where you bought it, we will arrange for a local service partner to provide the guarantee services. If you take the equipment outside the EU, the guarantee will not apply.
   • Of course, we are also happy to offer a chargeable repair service for any defects which are not covered or no longer covered by the scope of this guarantee. To take advantage of this service, please send the equipment to our service address. We draw attention to the restrictions of this guarantee concerning wear parts, consumables and missing parts as presented in the service information included in this operating manual.

Warrantor/ Service:
Einhell UK Ltd, Unit 10, 1st Floor, Champion‘s Business Park, Arrowe Brook Road, Upton, Wirral, CH49 0AB

Declaration of conformity: We declare conformity in accordance with the EU directive and standards for article

• First CE: 2023
• Art.-No.: 45.143.05 I.-No.: 21013 Subject to change without notice
• Archive-File/Record: NAPR029360
• Documents registrar:
• Cordless Hammer Drill/Screwdriver

Declaration of conformity

We, Einhell UK Ltd
Champions Business Park, First Floor Unit 10, Arrowe Brook Rd, Upton, Wirral CH49 0AB, United Kingdom declare the conformity to UK standards and legislation was assessed for:

Cordless Impact Drill TP-CD 18/80 Li-i BL (Einhell)
Article Number: 45.143.05 I.-No.: 21013 Subject to change without notice
Archive-File/Record: NAPR029360
Documents registrar: Christoph Egginger Wiesenweg 22, 94405 Landau/Isar, Germany

References

• Einhell Service
• service.com is for sale | www.brandforce.com
• VICE - VICE is the definitive guide to enlightening information.
• Einhell Service
• Herramientas de alta calidad para aficionados al bricolaje y la jardinería | Einhell.es
• Strumenti di alta qualità per gli amanti del Fai da Te e del giardinaggio | Einhell.it
• kwb Germany GmbH

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>