Epic Birdies 29 Inch Large 5 in 1 Tall Garden Bed Instruction Manual

: June 22, 2024
: EPIC

Table of Contents

Epic Birdies 29 Inch Large 5 in 1 Tall Garden Bed
Product Usage Instructions
IMPORTANT INFORMATION
Included components
Equipment needed
Instructions
FAQs
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Epic Birdies 29 Inch Large 5 in 1 Tall Garden Bed

Epic-Birdies-29-Inch-Large-5-in-1-Tall-Garden-Bed-PRO

Specifications:

Dimensions: Vary based on configuration chosen
Material: Aluzinc galvanized steel
Components: Bolts x124, Nuts x124, 8-hole channels x4, Straight sheets x6, Corner sheets x4, Wire bracing kit x4 of each section, Safety edge x1
Tools Required: Phillips screwdriver or cordless drill (Impact driver, Phillips bit, 8mm socket wrench, Bubble level – optional)

Product Usage Instructions

Preparation:
Make sure you have all the included components and necessary tools ready before starting the assembly process.

Assemble Side Panels:
Begin by assembling all side panels and installing bracing channels as indicated. Attach corners to the side panels ensuring proper overlap.

Select Wire Bracing:
Select wire bracing sections based on your chosen width configuration.

Brace Installation:
Slide each brace end from the top down over the channel. Affix the remaining bolts above each channel.

Final Assembly:
Separate panels for your chosen configuration lay them out, and affix the lowest bolts. Attach all nuts loosely and then tighten using a screwdriver or cordless drill.

Safety Edge Installation:
Remove protective plastic, push the safety edge over the rolled steel edge, and ensure it starts and finishes on a straight section of steel.

FAQs:

Does your Birdies bed have scratches from shipping?
Note that the bed is made of Aluzinc steel and is highly durable. Contact customer service for a can of exterior paint if needed.
Were your Birdie’s bed corners slightly bent during shipping?
You can easily bend the panels back into place using a cloth for protection. Refer to the provided YouTube video for assistance on re-adjusting the bent panels.

IMPORTANT INFORMATION

Read before beginning.

Note corners are sharp and could cause injury. Wear protective gloves when unpacking and handling these items; sensible shoes are also recommended. Until the clip-on safety edge is fitted all necessary precautions need to be taken to avoid injury.
Attach all nuts and bolts loosely, then use a cordless drill to tighten. Failure to tighten each nut and bolt to its maximum may result in failure.
Wear gloves to prevent injury when assembling the wire brace.
Place the bottom edge of the raised bed on a 1 inch layer of gravel/stone or free-draining sand. This allows for excellent drainage and also protects the bottom edge of the steel.
If filling the beds mechanically, fill the bottom 1/3 of the bed slowly. Do not climb into the bed while filling as this puts unnecessary pressure onto the bed.
When filling the bed avoid dumping onto the wire bracing.
Birdies beds are designed to handle the weight of organic-based soils from landscape suppliers only.
It is suitable to use the Hugelkultur method in the Birdies beds. Visit Epic Gardening on YouTube for more information.

Included components

Equipment needed

Phillips screwdriver or cordless drill

Optional:
- Impact driver
- Phillips bit
- 8mm socket wrench
- Bubble level
Recommended:
- Protective gloves
- Close-toed shoes

Configurations

Possible configurations:
Due to the manufacturing process bed sizing may vary +/- 2 inches.

$Epic-Birdies-29-Inch-Large-5-in-1-Tall-Garden-Bed- $2$$

Instructions

$Epic-Birdies-29-Inch-Large-5-in-1-Tall-Garden-Bed- $3$$

IMPORTANT: Ensure the safety edge starts and finishes on a straight section of steel, preventing detachment.

Scan the QR code for more details, tips, and solutions. Or, contact our customer service at: customerservice@epicgardening.com

FAQs

Does your Birdies bed have scratches from shipping?
Note that the paint isn’t actually the protective part of the bed. The bed itself is made of Aluzinc, one of the most durable galvanized steels out there. You won’t deal with any rust at all, even with the scrapes. Please contact customer service to have a can of exterior paint sent to you. It is an exact match for the coat that is already on the bed.
Were your Birdies bed corners slightly bent during shipping?
The panels can be easily bent back into place. Use a cloth to protect the metal when you re-adjust the bed and return it to its original state. After you’re done, it will be like new, especially when two beds are screwed together. Make sure to put the bent panel under the nonbent side. Ideally, placing bent panels on the bottom ensures any remaining imperfections aren’t visible. Check out this helpful YouTube video (growepic.co/bentpanels)).
Are you missing any hardware?
No problem at all! Just contact customer service and they will send the hardware to you right away.
Do I need a Bracing Kit?
Only our medium and large beds require a bracing kit which will be included in the box. If you need one (or more) for peace of mind or because you’re combining beds, you can purchase more from our store. Check out the following link for more information (growepic.co/bracinginfo).
Can I combine beds?
Yes! You can combine two beds together. We always recommend installing bracing bars when combining beds to prevent bowing due to soil pressure. For detailed instructions, visit (growepic.co/bracinginfo).
Can I place my Birdies Beds on a slope?
Indeed! Build a terraced slope with retaining walls, which looks quite nice but takes some effort. If you have a shallow slope and want to nestle your bed into it, refer to our YouTube video (growepic.co/slopeplacement) for bracing instructions.
How do I fill my Birdies bed?
Most models of Birdies beds can be configured to many different dimensions due to their panel construction. This causes the soil requirements to change based on the dimensions you choose. But not to worry! To make this simpler for you, we’ve created a chart for each model showcasing the dimensions and the required soil in both cubic feet and cubic yards. For taller models we recommend watching our YouTube video (growepic.co/filltallbeds) to save 60%+ on your soil costs.
What surface can I place my Birdies bed on?
Place your Birdies raised beds on any surface, from bare dirt to concrete. Here are our recommendations for each type of surface. Scan the QR code for instructions on various surfaces. This video also has details (growepic.co/bedsurfaces).

Certificate of Authenticity
Originally designed and made in Australia by Birdies Garden Products Produced in a factory powered by clean energy, that offers fair wages, prioritizes low waste production and steel recycling. Officially sold by Epic Gardening, the authorized distributor of Birdies Garden Products in North America.

CONTACT US: customerservice@epicgardening.com

Dear gardener,
It’s my pleasure to introduce you to our flagship product, the Birdies Raised Bed. Each raised bed is meticulously manufactured in Australia, in a solar powered, family-owned factory. As the original inventor of the metal raised bed, Birdies Beds are built by gardeners, for gardeners, and are designed to last 20+ years. They offer superior resistance to extreme weather conditions and dramatically better rust and corrosion prevention compared to standard metal beds. Setting up your garden isn’t just a purchase—it’s the start of a life-long relationship. We’re here for you, not only with best-in-class products to help you garden, but an entire ecosystem of
educational content on gardening, which you can find at www.epicgardening.com. If you have any product issues or feedback, email our dedicated customer support team at customerservice@epicgardening.com and we’ll get back to you as soon as possible. Thank you for choosing us and being a vital part of our simple, but audacious mission: to teach the world to grow.
Keep on growing,