EPIC OFFICE ET223T Apollo II Electric Corner Workstation Installation Guide

**EPIC OFFICE ET223T Apollo II Electric Corner Workstation Installation Guide

**

Apollo Corner Frame Setup Instructions

Technical data

Accessory list

Attention: The drawings below are only for reference which might be slightly different from the actual object. Any tools missing or installation problems, please contact customer service.

Component list

~~ No.~~

| ~~ Part| ~~ Qty| ~~ No.| ~~ Part|

~~ Qty~~

---|---|---|---|---|---
1|

Pedestal

| 3|

2

|

Lifting Column

|

3

No.|

Part

| Qty| No.|

Part

| Qty
0|
Supporting Beam| 2| ®|

Side Bracket

| 3
No.|

Part

| Qty| No.|

Part

| Qty
a|

Left Connecting Plate

| 1| ®|

Right Connecting Plate

| 1
No.|

Part

| Qty| No.|

Part

| Qty
|

Control Box

| 1| ®|

Handset

| 1
No.|

Part

| Qty| No.| Part| Qty
H|

Handset Screw

| 2| 0|

Switch Cord

| 1
No.|

Part

| Qty| |
8|

Power Plug

|

Note: There are three angles of installation for this type of desk, 90°, 120°, 180°
STEP : 1
Install left and right connecting plates

Connect the two supporting beams (3) to the left and right connecting plates (5) (6) with screws (C) and (E) respectively. There are three angles to choose , and finally tighten them with an allen key (I)

STEP 2
Install Columns

Connect the lifting columns (2) to the supporting beams (3) with screws (D), the middle column (2) to the left and right connecting plates (5) (6), and use an allen key (I) to tighten the screws; the installation methods of 90° and 180° placements are the same as 120°.
STEP 3-1
                     Install Pedestals

Assemble the feet and the lifting column (2) together, use a allen key (I) to tighten the screws(c).

STEP 3-2

Assemble the feet and the lifting column (2) together, use the allen key (I) to tighten the screws(C).
STEP 4
Install Side Brackets

Assemble te feet and the lifting column (2) together, use the allen key (I) to tighten the screws(C).
STEP 5
                                 Wire all Cables to Control Box
The wiring of 90°&180° placement are the same as 120° placement.

The cable tie (H) can be glued on the tabletop, and can also be screwed on the tabletop with screws (G).
STEP 6-1
                Install Tabletop and Handset

Install the control box(7) on the table board with screws(F), install the handset(8) with                                                    screws(9), use a pistol drill to tighten.
STEP 6-2
Install the control box(7) on the table board with screws(F), install the handset(8) with screws(9), use a pistol drill to tighten
STEP 6-3
Install the control box(7) on the table board with screws(F), install the handset(8) with screws(9), use a pistol drill to tighten.

Common fault treatment

The following tips will help you detected and eliminate the common fault and error. If the fault you met is not listed below, please contact with your supplier. Only the manufacturer and professionals are capable for investigating and correcting those fault and error.

loading: 150kg;
Automatically Self-Reset| Check if overloaded, max loading: 150kg;
Overload Operation| Restart after suspend for 18mins while connecting with power;
Can’t reach the min or max height| Press “M”and “3” together for 3 seconds or more, after hearing beep for twice, it will reset.

Attention

1. Power supply: AC200V-240V, 50/60Hz
2. Service Environment: 0-40℃
3. Unplug the power plug before cleaning, wipe the dust on surface with slight wet dishcloth when cleaning, be careful not to let the drops into the internal parts, not loose the connector.
4. The electric box contains electronic components, metals, plastics, wires etc., so dispose of it in accordance with each country’s environmental legislation, not the general household waste.
5. Check carefully to ensure correct and complete assembly before using.
6. Be familiar with all functions and program settings of the product before first use.
7. Children are forbidden to play on the product because of unforeseen action when playing, so any dangerous consequences caused by this improper action will not be on manufacturers.
8. Slight noise caused by the V-ribbed belt or brake system due to structure will not have any effect on the use of the equipment.
9. Corrosive or abrasive materials are forbidden to clean the equipment. Must ensure that the cleaner used will not pollute the environment.
10. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.
11. Cleaning and user maintenance shall not be made by children without supervision.
12. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly qualified person in order to avoid a hazard.
13. Please make sure there is no hazard sources in your operating environment. e.g., do not litter the tools around. Always be careful to treat the packaging materials in order to avoid any possible danger, e.g. plastic bag may lead to choking hazard to children.
14. Keep the original package of the equipment if necessary in case of the future use in transportation

Waste dispose
This marking indicates that this product should not be disposed with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>