SEALEY WCR02 Motorcycle Roll In Wheel Clamp Bolt Down Instruction Manual
- June 21, 2024
- SEALEY
Table of Contents
MOTORCYCLE ROLL-IN WHEEL CLAMP –
BOLT DOWN
MODEL NO: WCR02
WCR02 Motorcycle Roll In Wheel Clamp Bolt Down
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR
THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE
FOR FUTURE USE.
| 
| 
| 
---|---|---|---
Refer to instructions| Wear protectivegloves| Wear safety footwear| Wear
protective clothing
SAFETY
WARNING! Before use, ensure that there is nothing attached to the
motorcycle, that will foul on the clamp.
✔ Maintain the clamp in good condition (use an authorised service agent).
✔ Replace or repair damaged parts. Use genuine parts only. Unauthorised parts
may be dangerous and will invalidate the warranty.
✔ Locate the clamp in a suitable area. Keep area clean and tidy and free from
unrelated materials and ensure that there is adequate lighting.
Also ensure that the floor/ground is level and strong enough (preferably
concrete) to take the weight of the clamp and the motorcycle.
DO NOT mount the clamp on tarmacadam, as the surface may be unstable.
✔ Ensure that the clamps are free from oil and grease before positioning a
motorcycle in the clamp.
✔ Keep the clamp clean for the best and safest performance.
✔ Maintain correct balance and footing whilst positioning the motorcycle in
the clamp.
✔ Ensure that the floor is not slippery and wear non-slip shoes.
✔ Ensure that the motorcycle is adequately secured to the clamp if to be used
for transportation purposes.
✔ Keep children and unauthorised persons away from the work area.
DO NOT use the clamp for a purpose it is not designed to perform.
DO NOT operate the clamp if it is damaged.
DO NOT use the clamp when you are tired or under the influence of alcohol,
drugs or intoxicating medication.
DO NOT allow untrained persons to use the clamp.
DO NOT make any modifications to the clamp.
✔ Before removing a motorcycle from the clamp, ensure that there are no
obstructions or persons in the path of the motorcycle.
WARNING: The warnings, cautions and instructions in this manual cannot
cover all possible conditions and situations that may occur.
✔ It must be understood that common sense and caution are factors which cannot
be built into this product, but must be applied by the operator.
INTRODUCTION
Increases the stability of the motorcycle by clamping the bottom and front of the tyre. Features a pivot clamp which locks the front wheel securely by the motorcycle weight. Suitable for fitting on trailers, in vans or to motorcycle lifts (Requires suitable fixings). Fully adjustable to fit wheels Ø15”-21”(380-535mm). Minimum/Maximum tyre width: 50-130mm. Please note: Motorcycle must also be secured using tie-down straps. Fittings not included.
SPECIFICATION
Model No.:………………………………………………………..WCR02
Applications:
MC365, MC365A, MC401, MC401A, MC454, MC455, MCW360, MT400, MT700
ASSEMBLY
4.1. Bolt tyre stop in place (fig.1) using supplied fixings.
INSTALLATION
5.1.Identify the mounting holes in the base.
5.2. PERMANENT INSTALLATION.
5.2.1. Choose the installation site carefully so that there is good access to
both insert and extract the motorcycle from the clamp..
5.2.2. Ensure that the motorcycle and clamp DO NOT become a hazard.
5.2.3. Use anchor bolt fixings (not supplied) to secure the chock to a solid
concrete surface.
5.3. INSTALLATION FOR TRANSPORTATION.
5.3.1. When used for the transportation of motorcycles, the clamp must be
firmly bolted to the floor of the vehicle using suitable fixings.
5.3.2.Check the underside of the floor panel before drilling any holes. Make
sure that you DO NOT strike any important vehicle parts.
OPERATION
6.1. ADJUSTING THE CLAMP (FIG.1)
6.1.1. The pivot clamp has 10 locking positions. To adjust the clamp, extract
the ‘R’ clip and withdraw the pin. Move the pivot clamp to the desired
position, insert the pin and retain with the ‘R’ clip.
6.1.2. To obtain the optimum fit for differing sizes of motorcycle wheel,
adjust the position of the pivot clamp and then test as necessary.
6.2. POSITIONING MOTORCYCLE IN THE CLAMP
6.2.1. With the pivot clamp in the open position, align the motorcycle with
the clamp.
6.2.2. Push the motorcycle firmly into the clamp so that the tyre runs through
the tapered part of the pivot clamp.
6.2.3. As the weight of the wheel passes over the pivot clamp, it will cause
the clamp to flip over. The front of the tyre will be supported by
the tyre stop and the rear of the tyre by the pivot clamp.
6.2.4. Check that the motorcycle is stable within the clamp before leaving it.
If the wheel is loose, or too high in the clamp, extract the motorcycle from
the clamp and adjust the positions of the clamp until the optimum fit is
achieved.
6.3. REMOVING MOTORCYCLE FROM THE CHOCK.
6.3.1. More effort will be required to remove the motorcycle from the clamp.
Ensure that the space into which the motorcycle will move is free from
obstructions and people.
6.3.2. Take a firm stance and hold the motorcycle handlebar grips.
6.3.3. Pull back the motorcycle with sufficient force to overcome the hold of
the pivot clamp and release the motorcycle from the clamp.
MAINTENANCE
7.1. Keep the chock clean and wipe off any oil or grease.
7.2. Before each use check all parts. If any part of the chock is damaged or
defective, remove the chock from service and take the necessary action to
remedy the problem.
Parts support is available for this product. Please email sales@sealey.co.uk or telephone 01284 757500
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk.
IP32 7AR
01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk
© Jack Sealey Limited
Original Language Version
WCR02 Issue 1 07/09/20
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>