AM Alphamount APFS01 Floor TV Stand Instruction Manual

INSTRUCTION MANUAL
Rev02
APFS01
Floor TV Stand

APFS01 Floor TV Stand

AMZLAB GmbH
Laubenhof 23,45326 Essen
info@amz-lab.de
THEMIS AR support itd.
5 Great Portland St, London, United Kingdom.
info@amz-ab.de
Manufacturer: BESTQI INNOVATION (HONG KONG) TECHNOLOGY CO., LIMITED
Address: FLAT/RM 185 G/F HANG WAI IND CENTRE 6 KIN TAI ST TUEN MUN NT
support@alphamount.com

Before getting started, let’s make sure this stand is compatible.

1 Is the VESA pattern of your TV 50 x 50mm (2 x 2″)
to 200 x 200mm (7.9x 7.9|
---|---
2 Does your TV (including accessories) weigh less than 44 Ibs
(20kg) ?|
3 Tools Needed
(NOT Included)| Phillips Screwdriver
4 Important Safety Information| NOTE
● Please carefully read all instructions before attempting installation. If you DO NOT understand the instructions or have any questions or concerns, please call technical support or email customer service.
● Not all hardware included in this package will be used.
CAUTION
●  Avoid the risk of personal injury and property damage!
● DO NOT use this product for any purpose that is NOT explicitly specified in this manual. DO NOT exceed weight capacity. We are NOT liable for damage or injury caused by improper mounting,
incorrect assembly or inappropriate use.
● Before starting assembly, verify all parts are included and undamaged. DO NOT use damaged or defective parts. If you require replacement parts, please call technical support or email customer service.
WARNING
● This package contains small parts that may pose a choking hazard.
ATIP-OVER WARNING
Serious o fatal crushing injuries can occur from a tip-over accident.
To help prevent a tip-over accident:
● Never allow children to climb, stand, hang, or play on any part of the TV or TV stand.
● Use tip-over restraints (not included) or anchors (not included) to attach the TV stand to the wall
● Use of tip-over restraints may only reduce, but not eliminate risk of a tip- over accident.

Contents

Step 1 at Fits Your VESA Hole Pattern

The extender brackets should connect to the faceplate as demonstrated on the upper left. Do not fully tighten the bolts [G1] until Step 2 is finished.

Step 2 Attach the Faceplate with Extender Brackets to TV.

2-1 Select TV Bolts Hand thread bolts into the threaded inserts on the back of your TV to determine which bolt (M4, M6 or M8) to use. A minimum of 4-5 turns into the threading is required. Do not turn past the bottom of the hole.
2-2 Spacer and Bolt Configurations ![AM Alphamount APFS01 Floor TV Stand

• Figure 10](https://manuals.plus/wp-content/uploads/2024/06/AM-Alphamount- APFS01-Floor-TV-Stand-Figure-10.jpg)Flat Back TV (See Option A)

Curved TV (See Option B)
Bump (See Option C)
Cables (See Option D)
Recessed Holes (See Option E)
2-3 Attach the Faceplate with Extender Brackets to Your TV Option A Option A: For Flat Back TVs
Add spacers if needed to fit the bolt length and TV back.

Option B Option B: For Curved TVs
spacers must be tall enough so that the curved back of the TV does not interfere with the mounting plate.
Option C Option C: For TVs with a Bump
The faceplate must be flush on the bump and leveled by spacers on the gap.
Option D Option D: For TVs with Protruding Cables
Use spacers to create extra space between the TV and faceplate.
Option E Option E: For TVs with Recessed Holes
Spacers need to fill in the recessed holes on the back of the TV, while keeping the faceplate as close to the TV as possible.
When you finish securing the TV bolts into the TV, please remember to tighten the bolts [G1].

Step 3 Install the Base

Turn the feet [05] into the side base bracket [04]. Tighten the nut to fix the feet.
Note: Try to keep the feet on the same level.Attach the middle base bracket [03] to the lower pole [06] with the drop-shaped hole facing the front. Connect the base assemblies together.

Step 4 Install the Middle Pole

Attach the middle pole [07] with the drop-shaped hole facing the front.

Step 5 Connect the Upper Pole to the Middle Pole

The pole hes siaht height options. Choose the best height position for your TV before moving on to attach your TV to the pole. ![AM Alphamount APFS01 Floor TV Stand

• Figure 23](https://manuals.plus/wp-content/uploads/2024/06/AM-Alphamount- APFS01-Floor-TV-Stand-Figure-23.jpg)Insert the upper pole [08] and align it with the screw holes. Fix the nuts [M] with the wrench [G4], then tighten the bolts [I] to secure the upper pole [08].

Step 6 Secure the TV to the Upper Pole

Slightly tilt the connector for easier installation of the nut [M]. Slightly loosen the pre-assembled upper nut [S], then attach the TV. Secure the TV by tightening the nut [M] and the upper nut [S].

Step 7 Adjust the Tilt Angle of the TV

You can directly tilt your TV to your desired angle. If it is difficult to tilt the TV, slightly loosen  the tilt bolts [T], and then adjust your TV. To lock the tilt angle, fix the nuts with the wrench [G4] and retighten the bolts [T].

Step 8 Level the TV

Slightly loosen the nut [M]. Level your TV, then retighten the nut [M] to hold the TV in place. If the stand is not level on the floor, you can adjust the feet by turning the pre-assembled nuts on the feet for stability.

support@alphamount.com
860-00304-00 Rev02

Documents / Resources

| AM Alphamount APFS01 Floor TV Stand [pdf] Instruction Manual
860-00304-00, APFS01-E-Manual-XS, APFS01 Floor TV Stand, APFS01, Floor TV Stand, TV Stand, Stand
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>