KICHLER 52693BK Alvaro 8 Light 46 Inch Wide Taper Candle Style Chandelier Instruction Manual

: June 19, 2024
: KICHLER

Table of Contents

KICHLER 52693BK Alvaro 8 Light 46 Inch Wide Taper Candle Style Chandelier
FIXTURE DIAGRAM
PARTS LIST
CAUTIONS
INSTALLATION INSTRUCTIONS
Specifications:
Frequently Asked Questions (FAQ)
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

KICHLER 52693BK Alvaro 8 Light 46 Inch Wide Taper Candle Style Chandelier

INSTRUCTION MANUAL

FIXTURE DIAGRAM

PARTS LIST

[A] Outlet Box (Not Supplied)
[B] Strap Mounting Screw (2)
[C] Mounting Strap
[D] Mounting Screw (2)
[E] Canopy
[F] Lock Washer (2)
[G] Knob (2)
[H] Swivel (Attached to Canopy)
[I] Stems (2-12”, 2-6” with Short Threaded Tubes [J] installed)
[J] Short Threaded Tubes
[K] Main Body
[L] 20-1/2” Stem (with Short Threaded Tube [J] installed)

CAUTIONS

CAUTION – RISK OF SHOCK:

Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation.

WARNING:

1. This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended. Failure to adhere to these codes and instructions may result in serious injury and/or property damage and will void the warranty.

CLEANING:

Always be certain that electric current is turned off before cleaning.
Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.

INSTALLATION INSTRUCTIONS

NOTE: Thread locking compound must be applied to threads as noted with (4) symbol to prevent accidental rotation of fixture during cleaning, relamping, etc.

1. Screw 20-1/2” stem[L] into coupling on main body[K] using short threaded tube[J].

NOTE: The 20-1/2” stem must be used when mounting the fixture, and the 20-1/2” stem must be the first stem installed to the fixture as shown.

2. Pass fixture wires from 20-1/2” stem through desired number of short threaded tubes[J] and stems[I]. Screw stems together using short threaded tubes.
Screw first stem into end of 20-1/2” stem.
3. Pass fixture wire from last stem through end of swivel[H] and into canopy[E]. Thread the end of swivel into end of last stem. Note direction of swivel in accordance with ceiling.
4. Cut fixture wires a MINIMUM of 6 inches from the top edge of canopy.
5. Find the appropriate threaded holes on mounting strap[C] that align with hole distance in canopy. Assemble mounting screws[D] into threaded holes starting from the outlet box side.
6. Attach mounting strap to outlet box[A] using the supplied strap mounting screws[B]. Mounting strap can be adjusted to suit position of fixture.

7. Grounding instructions: (See Illus. a or b).
a. On fixtures where mounting strap is provided with a hole and two raised dimples, wrap ground wire from outlet box around green ground screw, and thread into hole.
b. On fixtures where a cupped washer is provided, attach ground wire from outlet box under cupped washer and green ground screw, and thread into mounting strap.

If fixture is provided with ground wire, connect fixture ground wire to outlet box ground wire with wire connector after following the above steps. Never connect ground wire to black or white power supply wires.

OUTLETBOX

8. Make wire connections. Reference chart below for correct connections and wire accordingly.

Connect Black or Red Supply Wire to:	Connect White Supply Wire to:
Black	White
*Parallel cord (round & smooth)	*Parallel cord (square & ridged)
Clear, Brown, Gold or Black without Tracer	Clear, Brown, Gold or Black with

Tracer
Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor

*Note: When parallel wire (SPT 1 & SPT 2) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (See illus.)

9. Raise canopy to ceiling, carefully passing mounting screws through mounting screw holes in canopy.

NOTE: Be certain wires do not get pinched between mounting strap and canopy or canopy and ceiling.

10. While holding canopy in place, use lock washers[F] and knobs[G] to secure canopy. Tighten to secure.
11. Insert recommended bulbs. (Not supplied).

We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST