Muxlab SE-001022-A 2 Channel XLR Wall Plate User Manual

: June 15, 2024
: MuxLab

Table of Contents

Muxlab SE-001022-A 2 Channel XLR Wall Plate
Product Usage Instructions
Safety Precautions
Introduction
Specifications
Installation
Operation and Control Functions
Application Diagram
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Muxlab SE-001022-A 2 Channel XLR Wall Plate

Specification

XLR Input : Balanced 20K Ohm
XLR Output : Balanced 100 Ohm
Dante interface : RJ45 interface, with PoE
Frequency response: 20Hz-20kHz
Sampling rate : 48kHz
Floor noise : -90dB
Channel Isolation : 100dB @ 1kHz
Form Factor : 2 Gang US
Power consumption : 2W
THD + N : Not specified
Operating temperature : Not specified
Dimensions (LxWxH): Not specified
Net Weight : Not specified
Warranty: Not specified
Order Information : Not specified

Product Usage Instructions

Safety Precautions
To ensure optimal performance and safety, please read the user manual carefully before using the Dante 2-Channel XLR Wall-Plate. Keep the manual for future reference.

Introduction
The Dante 2-Channel XLR Wall-Plate (Model 500558) allows non-Dante compatible analog audio equipment to connect with Dante compatible professional audio gear. It transmits full-range balanced two-channel analog audio signals over XLR to Dante equipment via the network. The unit is PoE powered and fits standard double gang US wall boxes.

Features

Enables connection between non-Dante analog audio equipment and Dante professional gear.
Transmits full-range balanced two-channel analog audio signals.
PoE powered.
Compatible with standard double gang US wall boxes.

Package Contents

One (1) Dante 2-channel XLR Wall-Plate
One (1) Standard type 120 wall box
One (1) Screwdriver
One (1) User manual (available via download)

FAQ

Q: What should I do if any accessories are missing from the package?
- A: If any accessories are missing, please contact the supplier from whom you purchased the unit for assistance.

Dante 2-Channel XLR Wall-Plate

User Manual

500558

© MuxLab Inc. 2024

94-001022-A/SE-001022-A

Safety Precautions

To ensure the best performance from the product, please read all instructions carefully before using the device. Save this manual for future reference.

Follow basic safety precautions to reduce the risk of fire, electrical shock, and injury.
Do not dismantle the housing or modify the module. It may result in electrical shock or burns.
Do not open or remove the housing of the device as you may be exposed to dangerous voltage or other hazards.
To prevent fire or shock hazard, do not expose the unit to rain, moisture and do not install this product near water. Keep the product away from liquids.
Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on the housing, unplug the module immediately.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
Using supplies or parts not meeting the product specifications may cause damage, deterioration or malfunction.
Refer all servicing to qualified service personnel.
Install the device in a place with adequate ventilation to avoid damage caused by overheat.
Unplug the power when left unused for a long period of time.
Information on disposal of devices: do not burn or mix with general household waste, please treat them as normal electrical waste.

Copyright Notice
All contents in this manual are copyrighted, and cannot be cloned, copied, or translated without the express permission of MuxLab Inc. Product specifications and information in this document are for reference only, and the content may be updated from time to time without prior notice.

Introduction

The Dante 2-Channel XLR Wall-Plate (Model 500558) permits non-Dante compatible analog audio equipment to interface with Dante compatible professional audio equipment. The unit allows the transmission of full-range (20Hz to 20KHz) balanced two channel analog audio signals on XLR over the network to Dante equipment. It is powered using the PoE from any PoE network switch. The Dante 2 channel XLR Wall-Plate is designed to be compatible with standard double gang US wall boxes.

Features

Interface analog audio equipment to Dante audio equipment
Supports balanced 2ch XLR analog audio input and 2ch XLR analog output. Audio sampling rate supports 48kHz (24bit)
Analog input with phantom power supply switch and gain manual adjustment knob. Power supply and audio transmission integrated in one cable
Designed to be compatible with standard double gang US electrical wall boxes. Shows the connection status through LED indicator light
Supports AES67 RTP audio transport
Supports PoE (IEEE802.3af)

Package Contents

One (1) Dante 2-channel XLR Wall-Plate
One (1) Standard type 120 wall box
One (1) Screwdriver
One (1) User manual (available via download)

Notes Confirm that the product and accessories are all included. If not, please contact the supplier from which you purchased the unit.supplier from which you purchased the unit.

Specifications

Specification

Installation

Dimensions

Dante 2-Channel XLR Wall-Plate
Suggestion: We recommend that you use the standard type 120 wall box we provide for your installation.

Insert the wall box into the wall, then use the screwdriver to remove the two screws in the middle of the panel, and take the down panel.
Connect the Ethernet cable, insert the main unit into the wall box and screw.
Place the cover panel and tighten the screws.

Operation and Control Functions

Power on the unit, the PWR indicator indicates the power supply status.
Download Dante Controller routing control software for input and output channel routing configuration. Other management software that supports Dante matrix mixing can also be configured.
The front face of the panel is shown below.
The phantom switch uses a hidden self locking button switch. When the switch is pressed, the button lights up, the Phantom power is turned on, otherwise the light goes out, and the Phantom power is closed.
The gain adjustment knob is hidden in the adjustment hole, and the input gain value of the corresponding channel is adjusted with a screwdriver. The gain range: 0~20dB.