OLIGHT Prowess EDC Flashlight User Manual

: June 18, 2024
: OLIGHT

Table of Contents

IN THE BOX
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Prowess EDC Flashlight
User Manual Prowess
A versatile EDC flashlight with dual-direction illumination.

IN THE BOX

Table 1:
Flashlight

Figure 1
Remove the insulating film

Note:

If you have an MCC charging cable and the detachable base is not available, you can use the MCC charging cable for charging.
The MCC is not included in the package. If necessary, please purchase it from Olight Store.
When using the MCC3 charging cable, the charging time is approximately 4.5 hours.

Figure 14
How to take the holster out of the fixing bracket

Multi-language dictionary, see Table 3;

Product specifications, see Table 1 and Table 2;
Operating instructions as below:
2.1 Remove the insulating film before first use, see Figure 1;
2.2 Charge, see Figure 2;
2.3 ON/OFF, see Figure 3;
Single press the switch quickly to turn on the light. When turned on, the flashlight will light up at the memorized brightness level. (Moonlight, Low, Medium, and High modes will be memorized when turned off. Turbo mode will be memorized as High mode; High mode output will last for 10 minutes before switching to Medium mode; Strobe mode will not be memorized.) Single press the switch again to turn off the light. The reverse light retains brightness memory for 1 minute after turning off and switches to the lowest output upon restart.
2.4 Lockout/Unlock, see Figure 4;
When the flashlight is off, press and hold the switch (for about 2 seconds) to access lockout mode (the flashlight will enter Moonlight briefly and then switch off to signal lockout mode activation). In lockout mode, if you operate the
switch for a non-unlock purpose, the indicator at the center of the switch will briefly light up red to signal that the light is still in lockout mode. To unlock it, please press and hold the switch for about one second until the Moonlight is on.
2.5 Moonlight, see Figure 5;
When the flashlight is off, press and hold the switch for over one second to access the Moonlight mode. If the light was turned off in Moonlight mode, simply press the switch.
2.6 Turbo, see Figure 6;
Forward light: Double press the switch quickly to activate Turbo mode, and double press again to return to the memorized brightness level. If the battery level is low, it returns to a lower output.
Reverse light: When the current brightness is ≥70%, double press the switch quickly to set the flashlight output to the lowest brightness. When the current brightness is <70%, double press the switch quickly to set it to the highest available brightness.
2.7 Choose between forward light and reverse light, see Figure 7;
Move the toggle switch upward for the forward light, and downward for the reverse light.
Forward light operation
3.1 Strobe, see Figure 8;
Press the switch 3 times or more to activate Strobe mode. To quit this mode, single press or press and hold the switch.
3.2 Change brightness level, see Figure 9;
When the light is on, press and hold the switch to adjust brightness. The flashlight will cycle through Low, Medium, and High modes, starting from the current brightness level. Release the button to select the desired brightness level. (Note: Moonlight and Turbo modes are not included in this cycle.)
Change the brightness level of the reverse light, see Figure 10;
When the light is on, press and hold the switch once to smoothly increase the brightness, and release to select the brightness level. To decrease the brightness level, press and hold again to smoothly decrease the brightness from the current brightness level. When the brightness level reaches its limits at the brightest or lowest setting, the light will flash twice to indicate that it has reached the highest or lowest level.
Battery level indicator, see Figure 11-1 & 11-2;
Detachable base application, see Figure 12;
How to use the fixing bracket, see Figure 13；
Begin by using tools to punch holes in the wall or wooden board, then insert the screw anchors. Next, remove the 3M adhesive sticker on the back of the fixing bracket and align it with the hole on the wall. Finally, secure the bracket
in place by screwing in the screws.(Note: Please stick the 3M adhesive sticker on a flat and smooth wall or car panel)
How to take the holster out of the fixing bracket, see Figure 14;
Press the holster against the fixing bracket, then pull it up and out of the fixing bracket.

Table 3
Multi-language dictionary

Moonlight Low Medium High Turbo Press Double press Press and hold Triple press
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
WEEE Disposal and Recycling Information
All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, to protect human health and the environment, you should dispose of your waste equipment at a designated collection point for the recycling of WEEE, appointed by the government or local authorities. Proper disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.

ISED Notice
This device complies with Industry Canada’s licence-exempt ICES
standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-005.
The light source of this luminaire is not replaceable:
when the light source reaches its end of life the whole luminaire shall be replaced.

EU Declaration of Conformity
Hereby Dongguan Olight E-Commerce Technology Co.,LTD declares that the equipment[Prowess] is in compliance with Directive 2014/30/EU and RoHS Directive 2011/65/EU & (EU) 2015/863. The full text of the EU declarant of conformity is available at the following internet address: https://www.olight.com/download

WARRANTY
We are proud to offer a lifetime warranty in Australia, China, France, Germany, and the USA. We are also working hard to expand coverage to more countries, where we provide a 2 or 5-year warranty. The warranty covers defects in material and workmanship under normal use, excluding loss, theft, deliberate damage, or cosmetic damage. For complete warranty information, please visit Olight.com or your local Olight official website.

Australia Customer Support
contact@olightstore.com.au
Austria Customer Support
kontakt@olightstore.at
Canada Customer Support
cs@olightstore.ca
China Customer Support
WeChat: Olight’s
France Customer Support
cs@olightstore.fr
Germany Customer Support
kontakt@olightstore.de
Italy Customer Support
contatto@olightstore.it
Japan Customer Support
cs@olightstore.jp
Korea Customer Support
olightkorea@olight.com
Spain Customer Support
contacto@olightstore.es
Thailand Customer Support
cs@olightstore.co.th
UK Customer Support
contact@olightstore.uk
USA Customer Support
cs@olightstore.com
For other countries and regions, please contact
Global Customer Support
contact@olight.com

Dongguan Olight E-Commerce Technology Co., Ltd.
4th Floor, Building 4, Kegu Industrial Park, No. 6 Zhongnan Road,
Chang’an Town, Dongguan City, Guangdong, China.
Made in China