Wuhan ZG32 Vision Enhancement Imager User Guide
- June 15, 2024
- Wuhan
Table of Contents
Wuhan ZG32 Vision Enhancement Imager
Thank you for purchasing this product. Please read this Guide first and keep it properly for future reference. We hope this product will meet your expectations.
Appearance (P1~P3)
| No. | Components | Functions |
|---|---|---|
| 1 | Lens cover | Protect the lens |
| 2 | Laser ranging | Used to measure the distance to the target. |
3
| ****
Left focus knob
| Rotate toward the eyepiece to zoom in
Rotate toward the objective lens to zoom out
4
| ****
Ranging button
| Short press: enable the ranging/single ranging
Long press: turn off the ranging/switch
the ranging mode
5
| ****
Menu Button
| Short press: bring up the function menu/confirm to save the settings Long press: bring up the setup menu/
exit the current menu without saving
6
| ****
Up Button
| Short press: Quickly switch between pseudo colors/switch between the menu options
Long press: exit the shortcut of the pseudo color menu/switch between the menu
options
7
| ****
Down Button
| Short press: take photos/switch between the menu options
Long press: record/switch between the
menu options
| No. | Components | Functions |
|---|
8
| ****
Power Button
| Short press: shutter compensation/ wake-up/exit menu
Long press: power on/off
9| MIC| Sound-recording port
10| Adjustment ring| Rotate to fix the daylight scope
11| Battery Compartment| Space for installing batteries
12| Type-C Port| Connect the PC and the external screen via type-C cable
13
| ****
Right focus knob
| Rotate toward the eyepiece to zoom out
Rotate toward the objective lens to zoom in
14| Adapter ring| Connect the device and the daylight scope
Battery installation (P2)
- Press the battery compartment cover buckle and pull out the battery compartment cover.
- Insert 2 batteries according to the positive and negative indications.
- Push on the battery compartment cover.
Data transmission (P2)
- Start the device to ensure it is in a power-on state.
- The device is connected to the PC through a USB-TypeC cable and “ALLOW” is selected on the device end to enter the mass storage mode.
- Access the data stored in the device from the PC.
Connection to mobile APP (P4)
- Start the device to ensure it is in a power-on state.
- Turn on the WiFi hotspot on the device.
- Search the WiFi hotspot name of the device through the mobile phone and connect.
- Open the TargetIR APP on the mobile phone to get a real-time image of the device. Then you can control and access the device.
Detailed operation
Scan the QR code for more methods of use.
FCC WARNING
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. The rating information is located at the bottom of the unit.
FCC RF Exposure Statement
The exposure standard for wireless devices employs a unit of measurement known
as the Specific Absorption Rate(SAR). The SAR limit set by the FCC is 1.6
W/kg. The highest SAR level measured for this device is less than the SAR
limit, so this device meets the FCC Requirement. This equipment may generate
or use radio frequency energy. Changes or modifications to this equipment may
cause harmful interference unless the modifications are expressly approved in
the instruction manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is made.
Special statement: the version of the guide will be updated after the technical improvement of the product.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>