Wuhan S600 Laser Rangefinders User Guide

Wuhan S600 Laser Rangefinders

FCC WARNING

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Important Notes
This Guide is a general guide for a series of products, which means that the specific model you receive may differ from the pictures in this Guide. Please refer to the actual product you receive. This Guide is organized for the convenience of users to use and understand our products. We will do our best to ensure the accuracy of the contents of this Guide. However, we still cannot guarantee the completeness of the contents thereof. As our products are subject to continuous upgrading, we reserve the right to modify this Guide from time to time without prior notice.

Introduction to Product Parts

1. Power on/off button
2. Ranging button

Precautions

Danger

1. Please charge the battery with the method described in this Guide and follow the charging procedure and precautions. Improper battery charging will cause heating, damage and even physical injury;
2. Do not try to open or disassemble the battery at any time. Once the battery leaks and the spill enters the human eye, wash the eyes with clean water immediately and take medical care.

Warning

1. When using the device, please try to keep it stable and avoid violent shaking;
2. Do not use or store the instrument in an environment that exceeds the allowable working temperature or storage temperature of the device;
3. Do not knock, throw or vibrate instruments and accessories to avoid damage;
4. Do not disassemble the machine by yourself, which may cause device damage and loss of warranty rights;
5. Do not use soluble or similar liquids on device and cables, which may cause damage to the device;
6. Please do not use the device in an environment that exceeds the operating temperature of the device, which may cause damage to the device;
7. Do not put the battery in a high-temperature environment or close to high-temperature objects;
8. Do not short-circuit the positive and negative poles of the battery;
9. Do not put the battery in a wet environment or water.

Caution

1. When this device is not used, please put the device and all accessories in a special packing box;

Storage and transportation

1. The storage environment of packaged products is -30℃~60℃, the relative humidity is not more than 95%, without condensation and corrosive gas, and is well ventilated and clean indoor;
2. Please take it out and charge it every 3 months.

Transportation

The laser rangefinder shall be protected from rain, water, inversion, violent vibration and impact during transportation, and shall be handled with care. Throwing is not allowed.

Quickstart Instructions

the device
Power on| Move down| Power off and turn off the power of the rangefinder
Ranging button| Ranging on| Short press| Refresh the distance
Long press| Switch between single/continuous

ranging mode

Ranging off| /| /

[Button description]
Move up to turn on the laser ranging and Bluetooth and automatically connect with the Bluetooth of the device. After connecting with the Bluetooth of the device, the rangefinder enters single ranging mode by default.

Power off
Move down to turn off the power of the rangefinder.

Ranging button

Ranging
Long press the Ranging button to switch the ranging mode between single ranging and continuous ranging modes. In the case of single ranging, short press the Ranging button to immediately refresh the current distance value. In the case of continuous ranging, the distance value is refreshed automatically every second.

Common Troubleshooting Guide

1. The rangefinder fails to connect with the Bluetooth of the device.

Solution

1. Restart the rangefinder or replace the battery, and the Bluetooth connection is successful when the Bluetooth icon on the device stops flashing;
2. Make sure that the ranging function of the device is turned on or turn on the ranging function of the device again;
3. Move the rangefinder close to the device so that the rangefinder and the device are within the range of connection;
4. Turn off the ranging function of other devices to make sure that the rangefinder is not connected to other devices.
5. No distance value is displayed on the device

Solution

1. Make sure that the target is within the range range of the rangefinder (5m~600m). The rangefinder cannot measure the distance less than 5m and greater than 600m.
2. Make sure that no other objects are obstructing the sensor of the laser rangefinder.
3. The distance value on the device is not refreshed
4. Short press the Ranging button to immediately refresh the distance value or long-press the Ranging button to switch to the continuous ranging mode.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>