tuya SMKG-1KNL-W Wi-Fi Smart Circuit Breaker Instruction Manual
- June 13, 2024
- Tuya
Table of Contents
Wi-Fi Smart
Circuit Breaker
Instruction Manual
Main Function
Main Data Parameter
Protocol: Wi (Default)
Rated Operating Voltage Range: 90V-240V
‘Control Type: Remote Control, Manual
Poles Description: 1P+N (N Pole Pass-through)
Customization: Lora / SigMesh / RS485 / RJ4S
Model selection: Non-metering Type
Metering Type (1~63A current adjustable)
Indicator Description
Non-metering Type.
- The LED indicator shows a blue light. indicating that the device s in an on state.
- The LED indicator shows a ight out, indicating that the device s ina o state.
- The LED indicator shows blue flashing, indicating that the device Is i pairing mode
Metering Type
- The LED indicator shows a blue light, indicating that the device has been connected 1o the network.
- The LED indicator shows blue lashing. indicating that the device s in pairing mode.
- The LED indicator shows a light up, indicating that the device Sinan offline state
- The button indicator shows light up, indicating tha the device s in an on state.
- The button Indicator shows a ight ot indicating that the device is ina of state.
Live View (Metering Type Only)
Can monitor the current, voltage, and power of the load equipment in real
time, and can also record the power consumption of the year, month, day, hour,
and different time periods, helping users to check the power consumption of
load
equipment more clearly. Setting the switch status of the equipment in
different scenarios, and remotely monitor the real-time situation of the load
electrical appliances.
Configuration Steps
First Step: Connect the wires from the upper of the Wi-Fi Din Rail Switch, connect the live wire to the L pole and the neutral wire to the Noel, please make sure that the wiring is correct and the WiFi signal is strong.
Second Step:
Download, register and log in to the “Smart Life” or “Tuya Smart” App.
Connect your phone to 2.4GHz WiFi and turn on Bluetooth.
Ensure that the device is in pairing mode(LED indicator is blinking).
If the wifi indicator is not blinking, please reset the device: long press the
power button for 5 seconds, the wifi indicator blinks. Third Step:
Click “Add Device” and the device will be automatically searched for on the
“Add Device” page. Then click “Add”. Fourth Step:
Enter your WiFi account and password, and click ‘Next’.
Wait patiently, the device is connecting to the network.
Fifth Step:
Click ‘Done’ and the device has been successfully added.
Sixth Step:
After successful connection, the LED indicator light will change from
flashing blue to stopping flashing.
Installation And Wiring Diagram
This product does not have isolating function and short circuit protection
function, and requires a circuit breaker to be configured at the upper part
for use.
The wiring is shown in the figure.
Download APP
https://a.smart321.com/tuyasmartlifeiot
Scan the QR cade below to watch the tutorial.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
esidential installation. This equipment generates, uses and can tadiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly
approved by the party.
Responsible for compliance could void the user’s authority to operate this
equipment. (Example- use only shielded interface cables when connecting to
computer or peripheral devices).
This equipment complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
The equipment complies with FCC Radiation exposure limits set forth for
uncontrolled enviroment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>