PHILIPS MG5930-15 All in One Trimmer User Manual

All-in-one
trimmer

MG5930/15

MG5930-15 All in One Trimmer

Important safety information

Read this important information carefully before you use the appliance and its accessories and save it for future reference. The accessories supplied may vary for different products.

Warning
– To charge the product, only use a certified safety extra low voltage (SELV) supply unit with output rating 5 V, ≥ 1 A. For safe charging in a moist environment (e.g. in a bathroom), only use an IPX4 (splash-proof) supply unit. A suitable supply unit (e.g. Philips HQ87) is available via www.philips.com/support. If you need support finding the correct USB supply unit, contact the Consumer Care Center in your country (see the international warranty leaflet for contact details). Using a non-certified supply unit may cause hazards or serious injuries.
– Keep the USB cable and the USB supply unit dry (Fig. 2).
– This appliance is waterproof (Fig. 3). It is suitable for use in the bath or shower and for cleaning under the tap. For safety reasons, the appliance can therefore only be used without cord.
– This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
– Do not modify the supply unit.
– Do not use the supply unit in or near wall sockets that contain an electric air freshener to prevent irreparable damage to the supply unit.
– Do not use a damaged appliance. Replace damaged parts with new Philips parts.
– Because of hygiene, only one person should use the appliance.
– Unplug the appliance before cleaning it with water.
– Only use cold or lukewarm water to clean the appliance.
– Never use compressed air, scouring pads, abrasive cleaning agents or aggressive liquids to clean the appliance.
– Only use original Philips accessories or consumables.
– Charge, use and store the product at a temperature between 5 °C and 35 °C.
– Keep product and batteries away from fire and do not expose them to direct sunlight or high temperatures.
– If the product becomes abnormally hot or smelly, changes color or if charging takes longer than usual, stop using and charging the product and contact Philips.
– Do not place products and their batteries in microwave ovens or on induction cookers.
– Do not open, modify, pierce, damage or dismantle the product or battery to prevent batteries from heating up or releasing toxic or hazardous substances. Do not short-circuit, overcharge or reverse charge batteries.
– If batteries are damaged or leaking, avoid contact with the skin or eyes. If this occurs, immediately rinse well with water and seek medical care.

Electromagnetic fields (EMF)

This Philips appliance complies with all applicable standards and regulations regarding exposure to electromagnetic fields.

Introduction

Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome.
You can find the model number on the back of your product.
The full model number (e.g. MG1234/56) is located on the bottom of the packaging, your receipt or order confirmation.

Features (Fig. 1)

1. Nose and ear hair trimmer

2. Skin protector

3. Body groomer

4. Full-size hair trimmer

5. On/off button

6. Battery status indicator

7. Socket for small plug

8. USB cable
   Note: A suitable power source (e.g. Philips HQ87) is available via www.philips.com/support.

9. Adjustable beard and hair comb 3 mm – 7 mm

10. Stubble comb 1 mm

11. Stubble comb 2 mm

12. Hair comb 9 mm

13. Hair comb 12 mm

14. Hair comb 16 mm

15. Body comb 3 mm
    Not shown: cleaning brush and pouch

Charging

– Charging or using the appliance at temperatures below 5 °C or higher than 35 °C adversely affects the lifespan of the battery.
– If the appliance is subjected to a major change in temperature, pressure or humidity, let the product acclimatize for 30 minutes before use.
Charge the appliance before first use and when the battery status indicator shows that the battery is almost empty. When the appliance has charged for 60 minutes, it has a cordless operating time of 120 minutes.

Warning: Keep the USB cable and the USB power source dry (Fig. 2).

1. Make sure that the appliance is switched off.
2. Insert the small plug of the USB cable into the socket in the bottom of the appliance (Fig. 5).
3. Insert the USB plug into the USB power source (not included) (Fig. 6).
4. Insert the USB power source into the power outlet (Fig. 7).
5. After charging, remove the USB power source from the power outlet and pull the small plug out of the appliance.

Quick charge
After approx. 5 minutes of charging, the appliance contains enough power for one cordless trimming session.

Battery status indications

Note: Approx. 30 minutes after the battery is fully charged, the battery status indicator switches off automatically.

Using the appliance

Trimming tips
– When trimming for the first time, start by using the comb with the maximum trimming length setting to familiarize yourself with the appliance.
– Since all hairs do not grow in the same direction, you may want to try different trimming directions (i.e. upwards, downwards, or across). Practice is best for optimum results.
– Always make smooth and gentle movements and be sure the surface of the comb always stays in contact with your skin.
– For best results, use the appliance on clean, dry hair, as wet hair tends to stick to the body.
– When too many hairs have accumulated on the appliance, remove the hairs before and/or during use, for best trimming results.

Detaching and attaching cutting elements

1. To detach a cutting element, place your finger near the teeth of the cutting element and push gently upwards until the cutting element is released from the handle (Fig. 8).
2. To attach a cutting element, insert the plastic notch at the back of the cutting element into the guiding slot in the handle and gently press the teeth of the cutting element downwards until they click into place (Fig. 9).

Attaching and detaching combs

1. To attach any type of comb onto a cutting element, slide the front part of the comb onto the teeth and press the notch at the back of the comb downwards until it clicks into place (Fig. 10).
2. To detach any type of comb from the cutting element, carefully push its back part off the appliance and then slide it off the cutting element (Fig. 11).

Detaching the nose and ear hair trimmer

1. Place your finger on the recess at the back of the attachment and push the attachment off the handle (Fig. 12). Use your other hand to prevent the attachment from dropping on the floor.

Comb colours
The combs provided with the appliance have different colors depending on their intended use. Select the type of comb suitable for the part of the body that you want to trim.

Switching the appliance on and off
To switch the appliance on or off, press the on/off button once.
Attachments for use on beard
Always comb your beard or moustache with a fine comb before you start trimming.
Full-size hair trimmer
Use the full-size hair trimmer without a comb to trim hair close to the skin (to a length of approx. 0.5 mm) or to create clean lines around your beard, neck and sideburns.

1. To trim hair close to the skin, place the flat side of the cutting element against your skin and make strokes against the direction of hair growth (Fig. 13).
2. For contouring, hold the cutting element perpendicular to the skin and move it upwards or downwards with gentle pressure.

Attach a black beard comb to the full-size hair trimmer to trim your beard and mustache evenly to the desired length. The appliance comes with 2 black beard combs.
The numbers on the combs relate to the number of millimeters of hair length that will remain after trimming.

1. Attach a beard comb to the full-size hair trimmer.
2. To trim in the most effective way, move the comb against the direction of hair growth. Make sure that the surface of the comb always stays in contact with the skin.

Attachments for use on beard and head Adjustable beard and hair comb
Use the black adjustable beard and hair comb to trim your beard or scalp hair evenly to the desired length ranging from 3 mm to 7 mm. The numbers on the comb relate to the number of millimeters of hair length that will remain after trimming.

1. Attach the adjustable beard and hair comb to the full-size hair trimmer (see ‘Attaching and detaching combs’).
2. Use the slide switch on the comb to adjust the length (Fig. 14).
3. To trim in the most effective way, move the comb against the direction of hair growth. Make sure that the surface of the comb always stays in contact with the skin.

Attachments for use on head
Always comb your hair before you start trimming.
For best results, use the appliance on clean, dry hair.
Attach a black hair comb to the full-size trimmer to trim your scalp hair evenly to the desired length. The appliance comes with 3 black hair combs. The numbers on the combs relate to the number of millimeters of hair length that will remain after trimming.

1. Attach a hair comb to the full-size hair trimmer (see ‘Attaching and detaching combs’).
2. Move the trimmer slowly over the crown from different directions to achieve an even result. Make sure that the surface of the comb always stays in contact with the skin.
3. Always move the trimmer against the direction of hair growth (Fig. 15). Press lightly.
4. Make overlapping passes over the head to ensure that all hair that should be cut has been cut.
5. Gently shake the hairs off the appliance in between strokes to prevent hairs from collecting between the cutting element and the comb.

Attachments for use on body
Always use a body comb when trimming sensitive areas.
Body combs
Attach a light gray body comb to the full-size hair trimmer to trim hairs below the neckline. The appliance comes with 1 body comb. Use the body comb to trim your body hair to the length of 3 mm.

1. Attach the body comb to the full-size hair trimmer (see ‘Attaching and detaching combs’).
2. To trim in the most effective way, stretch the skin with your free hand and move the comb against the direction of hair growth (Fig. 16). Make sure that the surface of the comb always stays in contact with the skin.

Body groomer
Use the body groomer to shave hair below the neckline such as your underarms and chest.
Only use the body groomer with the skin protector.

1. Attach the body groomer to the appliance (see ‘Detaching and attaching cutting elements’).
2. Attach the skin protector to the body groomer (Fig. 17).
3. To shave in the most effective way, stretch the skin with your free hand and move the groomer against the direction of hair growth (Fig. 18). Make sure the surface of the groomer always stays in full contact with the skin.

Precision attachments for use on face Nose and ear hair trimmer
Use the nose and ear hair trimmer to trim your nose and/or ear hair.
– Make sure nasal passages are clean. Make sure outer ear channels are clean and free from wax.
– Do not insert the cutting element too deep into your nostrils or ear channels (max. 5 mm).
– When trimming both nose and ear hair, make firm, rotary movements to ensure that the cutting element reaches all the hairs.
– Clean the nose and ear hair trimmer after each use.

Note: The nose and ear hair trimmer is not designed to clean-shave your nostrils or ear channels, but to cut the hairs to a shorter length. Nose and ear hairs have important protective functions and should not be fully removed.

Trimming nose hair

1. Gently insert the cutting element into one of the nostrils. Move the tip in and out of the nostril in a firm, rotary motion to cut the hairs to a shorter length (Fig. 19).

Trimming ear hair

1. Slowly move the cutting element along the outer ear to trim hairs that stick out beyond the rim.
2. Gently insert the cutting element into the outer ear channel. Move the tip in and out of the outer ear channel in a firm, rotary motion to cut the hairs to a shorter length (Fig. 19).

Cleaning

– Clean the appliance after each use (see ‘Cleaning’).
– Switch off the appliance before removing or attaching attachments and before cleaning.
– Never use compressed air, scouring pads, abrasive cleaning agents or aggressive liquids such as gasoline or acetone to clean the appliance.
– Caution: Never dry the trimmer teeth with a towel or tissue, as this may damage the trimmer teeth.

After every use: cleaning under the tap

1. Make sure that the appliance is switched off and that the USB power source has been removed from the power outlet and from the appliance.
2. Remove any comb (see ‘Attaching and detaching combs’) and cutting element (see ‘Detaching and attaching cutting elements’) from the appliance.
3. Rinse the hair chamber under running tap water (Fig. 20).
4. Clean the cutting element and comb under running tap water.
5. Carefully shake off excess water and let all parts airdry completely.

Thorough cleaning

1. Make sure that the appliance is switched off and that the USB power source has been removed from the power outlet and from the appliance.
2. Clean the handle under the tap or wipe the handle clean with a dry or moist cloth.
3. Remove any comb (see ‘Attaching and detaching combs’) or cutting element (see ‘Detaching and attaching cutting elements’) from the appliance.
4. Remove any hairs that have accumulated in the hair chamber with the cleaning brush supplied.
5. Remove any hairs that have accumulated in the cutting elements and/or combs with the cleaning brush supplied.
6. Rinse the cutting elements and combs under running tap water.
7. Carefully shake off excess water and let all parts airdry completely.

Cleaning the nose and ear hair trimmer
Clean the nose and ear hair trimmer immediately after use and when a lot of hair or dirt has accumulated on the cutting element.

1. Rinse the nose and ear hair trimmer head under running tap water (Fig. 21).

2. Switch on the appliance and rinse the cutting element once more to remove any remaining hairs. Then switch off the appliance again.
   If a lot of hair or dirt accumulates on the cutting element, this can hinder or decrease the performance of the nose and ear hair trimmer. For a thorough clean, detach the nose and ear hair trimmer head from the appliance and immerse it in a bowl with warm water for a few minutes to soak and soften the debris. Reattach the nose and ear trimmer head and switch on the appliance to rinse off stubborn hair/debris.

3. Carefully shake off excess water and let all parts airdry completely.

Cleaning the body groomer

1. Remove the skin protector by pulling it upwards off the groomer.
2. Clean the skin protector and body groomer under running tap water (Fig. 22).
3. Carefully shake off excess water and let both parts air-dry completely.
4. Reattach the skin protector onto the body groomer (Fig. 17).

Storage
Note: Do not place or store the appliance where it can fall or be pulled into a tub or sink, water or other liquid while plugged in.
– Make sure that the appliance is switched off and that the USB power source has been removed from the power outlet and from the appliance.
– Do not wrap the USB cable around the appliance when storing.
– Store the appliance, the USB power source and all the accessories in the pouch supplied. Place the pouch in a safe, dry location, where it will not be crushed, banged, or subject to damage.
– Make sure that the appliance and the accessories are dry before you store them in the pouch.

Support
For all product support such as frequently asked questions, please visit www.philips.com/support. Cutting units are not covered by the terms of the international warranty because they are subject to wear.
Ordering accessories
To buy accessories or spare parts, visit www.philips.com/parts-and- accessories or go to your Philips dealer. You can also contact the Philips Consumer Care Center in your country (see the international warranty leaflet for contact details).

Recycling
– This symbol means that electrical products and batteries shall not be disposed of with normal household waste (Fig. 4).
– Follow your country’s rules for the separate collection of electrical products and batteries.

Removal of built-in rechargeable battery
The built-in rechargeable battery must only be removed by a qualified professional when the appliance is discarded. Before removing the battery, make sure that the appliance is disconnected from the wall socket and that the battery is completely empty.

Take any necessary safety precautions when you handle tools to open the appliance and when you dispose of the rechargeable battery.
When you handle batteries, make sure that your hands, the product and the batteries are dry.
To avoid accidental short-circuiting of batteries after removal, do not let battery terminals come into contact with metal objects (e.g. coins, hairpins, rings). Do not wrap batteries in aluminum foil. Tape battery terminals or put batteries in a plastic bag before you discard them.

1. Remove the cutting element (Fig. 8).
2. Unscrew the screws at the bottom and at the top of the handle (Fig. 23), and remove the top ring (Fig. 24).
3. Remove the bottom cap of the handle together with the motor unit and the power supply unit with the rechargeable battery (Fig. 25).
4. Unsnap the bottom cap (Fig. 26).
5. Separate the supply unit from the motor unit (Fig. 27). Unsnap the battery frame from the power supply unit with the rechargeable battery (Fig. 28). You can now dispose of and/or replace the rechargeable battery.

References

• Philips Customer Service Support - Home | Philips
• Product registration | Philips

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>