JMTek Industries BTE400 Bluetooth Earbuds Instruction Manual
- June 9, 2024
- Jmtek Industries
Table of Contents
- JMTek Industries BTE400 Bluetooth Earbuds Instruction Manual
- Product diagram
- Headset Configuration
- Packing list
- Charging bin configuration parameters
- Wearing a way
- Mode of operation
- Pairs of ears connected
- Binaural touch operation
- FCC Warning
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
JMTek Industries BTE400 Bluetooth Earbuds Instruction Manual
FCC ID: 2APU5-BTE400
Product parameters are laboratory test data, the specific data is subject to the use of data
Product diagram
Headset Configuration
- Product model: BTE400
- Version: 5.3
- Running time: about 5 hours
- Call time: approximately 5 hours
- Operation mode: touch operation
- Charging time: about 1 hour
- Effective distance: >10 m
- Horn: copper ring 13mm
Packing list
- charging box *1
- Left and right earphones *1
- Product Manual *1
- Charging cable *l
Charging bin configuration parameters
- Material: ABS
- Charging time: about 1 hours
Wearing a way
Open the cover of the charging bin, take out the earphone of the right ear, gently put the speaker end of the earphone into the ear canal of the right ear, and then gently sway the earphone not to shake.
Mode of operation
-
The boot
(1) Open the charging compartment cover, take out the earphones, automatically turn on, earphones red and blue lights flashing
(2) When the headset is off, touch the touch pad of the headset for 3 seconds to start the headset -
To turn it off
(1) Put the earphon e back into the charging bin and close the cover . The earphone will be turned off and charged
(2)When the headset is on, touch the touch pad of the headset for 4 seconds to turn it off
Pairs of ears connected
- 0pen the cover of the charging compartment, take out the earphone and start it automatically. The earphone breathing light flashes,and enter the automatic team formation state. one of the earphone lights is off, indicating that the team formation is successful
- Open the device wireless list and search for “BTE400”
- Click“BTE400”to connect.If the connection fails put the earphone back into the charging bin and cover it,and then repeat the above steps
- When both ears leave the normal connection distance with the device at the same time, the headset will enter the wireless headset connection state. If the connection is not successful within 5 minutes,the headset will automatically shut down.
After the device is connected for the first time, the headset will automatically connect to the last pair device when it is restarted next time
Binaural touch operation
Earphone charging: Put the earphone into the charging box to automatically charge, close charging cover, the red LEDs will be illuminated, red LEDs will turn off when fully charged.
Charging box low power: The single digit of the digital tube flashes.
Charging box charging: The single digit of the digital tube flashes, and it stops when it is fully charged and 100 is displayed in digital tube.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>