HECATE G2BT Low Latency Bluetooth Gaming Headset User Manual
- June 3, 2024
- HECATE
Table of Contents
HECATE G2BT Low Latency Bluetooth Gaming Headset
Product Description
- LED indicator
- Multi-function “G” button
- Volume up button
- Volume down button
- Charging port
- Microphone
Product Accessories
Note:
Images are for illustrative purposes only and may differ from the actual
product.
Power ON/OFF
Charging
Pairing
- For initial use, press and hold the multi-function “G” button for 5s, the headphone will enter Bluetooth pairing state. LED will blink red and blue alternately.
- For subsequent use, power on and press and hold the multi-function “G” button for 3s to enter Bluetooth pairing state.
Resetting
Press and hold the multi-function “G” and volume up “+” button simultaneously for 5s to reset.
Controls
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment could be installed and operated with minimum distance 0 cm between the radiator and your body. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. IC statement:CAN
ICES-003(B)/NMB-003(B).
Declaration for EU Frequency Band: 2.402GHz – 2.480GHz RF Power Output: 13 dBm
(EIRP) There is no restriction of use. Input: 5V=500mA
Model: EDF700033
FCC ID: Z9G-EDF196
IC: 10004A-EDF196
Edifier International Limited
P.O. Box 6264
General Post Office
Hong Kong
www.edifier.com
© 2022 Edifier International Limited. All rights reserved.
Printed in China
www.hecategaming.com
Designed by DONGGUAN EDIFIER ESPORTS TECHNOLOGY CO.,LTD.
NOTICE:
For the need of technical improvement and system upgrade, information
contained herein may be subject to change from time to time without
prior notice.
Products of EDIFIER will be customized for different applications.
Pictures and illustrations shown on this manual may be slightly different from
actual product.
If any difference is found, the actual product prevails.
Hereby, Edifier International Limited declares that the radio equipment type
EDF700033 is in compliance with Directive 2014/53/EU. The full text of the EU
declaration of conformity is available at the following internet address:
https://www.edifier.com/int/eu-doc.html
FCC Regulatory Compliance
Warning: changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Compliance
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
ISED Regulatory compliance
This device contains license exempt transmitters that comply with Innovation,
Science and Economic Development Canada’s license exempt RSS(s). Operation is
subject to the following two conditions:
This device may not cause interference.
This device must accept any interference, including interference that may
cause undesired operation of the device.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>